Laser Safety Information This drive employs a laser. Do not remove the cover or attempt to service this device when connected due to the possibility of eye damage. CAUTION Use of control of adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. This label is located on top enclosure of this drive. DANGER VISIBLE AND INSCRIBER LASER RADIATION WHEN OPEN.
NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents Heed the following Warning Caution Cautions Cleaning... Handling the Disc Part Names and Functions Front View. Rear View Preparation Jumper installing the DVD RWY drive in a host PC Inserting/Removing a Disc Using the DVD RWY Drive Installed Vertically 14 Inserting a Disc 18 Removing a 18 Emergency Eject Specifications DVD Section.
HEED THE FOLLOWING Read the operating instructions carefully before using the unit and be sure to use it properly, After reading the instructions, store them inn easily accessible place so they can be consulted whenever necessary. AN WARNING + Continued use should there be an irregularity (smoke, abnormal small or sound, tee) will lead to fires or electric shocks.
A caution B « When connecting computer equipment, audio equipment, speakers, etc., be sure to read the respective manuals carefully, turn of the power and follow the connection instructions. Using cords other than the specified cords or extending cords could generate heat and result in burns, etc. B + Set the volume to the minimum before turning on the power. Sudden bursts of loud sound could result in hearing impairment.
Cautions Cleaning To clean the DVD RWY drive, wipe it with a soft, damp doth, using mild detergent if necessary. Please avoid using solvents such as benzine or paint thinner. This can cause color changes or deformation of DVD IRWIN drive. Handling the Disc + De not touch the data side of the disc (the side of the disc with no label or printing}. + Do not apply paper labels or write on any part of the disc, data side or label side. Do not use the disc leaved a mark strip paper labels.
Part Names and Functions Front View 0 © [==l7 Phones Jack This jack is used fo connect a set of headphones. Please use headphones with a stereo mini-jack plug. 2 Volume Control } This control is used (o adjust the headphone volume, NOTE: This control has no effect on the audio output from the LINE QUT connector on the back of the DVD RWY drive. 3 BUSY Indicator This indicator lights green white data is being read and written. 4 Tray Panel This panel prevents dust from entering the DVD RWY drive.
Rear View
Preparation Jumper Setting A jumper consists of a pair of pins and a connector which fits aver the pins. When the connector is in place it establishes an electronic link between the ping, which enables the function being controlled by the jumper. if the connector is removed, the electronic link is broken and the function is disabled. JUMPER BLOG CHISEL SLAVE MASTER Jumpers are used to set the DVD RRW drive mode on the IDE interface.
Installing the DVD IRWIN drive in a host PC Note Refer to the guidebook included with your personal computer for instruct-tions on Installing the DVD RWY drive. This chapter gives one example of installation. And, when disconnecting the DVD RWY drive from computer equipment, please wait to remove a couple of minutes until it gets cold” The enclosure may have some points over 60°C. 1. Attach the mounting rails to both the left and right sides of the DVD RWY drive. 2.
5. Locate a spare power cable in your computer. 8. Connect that power cable to the power connector on the back of the DVD RWY drive.
7. Connect the FO BUS connector on the DVD IRWIN drive and the IDE corrector. Connect the colored stripe side of the cable to the side marked with the arrow BUS CONNECTOR 8. Slide the disc drive and DVD RWY drive into the computer, 9. Replace the mounting clips, keeper bracket, and computer cover. “13.
Inserting/Removing a Disc Using the DVD RWY Drive Installed Vertically When using the DVD RWY drive, in the vertical position, load and unload discs as shown on the diagram below, OVD IRWIN drive installed medically DVD RWY drive installed vertically {eft side) {right side) Caution Only 120m discs can be used when the DVD RWY drive is installed vertically. Do not place Bom discs in the tray when using the DVD IRWIN drive installed in this way.
Inserting a Disc ’ 1. Press the Load/Eject button. The disc tray will be ejected. 2. Place the disc in the center of the tray with the label side facing up. 3. Press the Load/Eject button. The disc tray will be retracted. Removing a Disc 1. Press the Load/Eject button. The disc tray will be ejected. 2, Remove the disc. 3. Press the Load/Elect bunion. The disc tray will be detracted. WARNING: Do not forcibly push the disc tray in by hand. Doing so may result in damage.
IDE Interface Section Burst Transfer Rate PIO mods 4 DMA Single Word mode 2 DMA Ult Word mode 2 lies DAM-38 mode 2 Memory Buffer 2 Bytes Audio Section FREQUENCY RESPOND 20 Hz. 20 kHz RATIO... > BUG (Kuhn} “Total Harmonic Distortion on OD (KHZ) Wow & Flutter. Below measurable nits, Duplicate 0.7 V (ims) *30dB/10kivad Environment Ambient conditions for use Temperature +5 10 450°C Humidity {nic condensation) Ambient conditions for storage Temperature 20°C to +600 Humidity condensation} General Power Supp ..