Mobile Terminal EX User’s Guide Before using Mobile Terminal EX, read "Mobile Terminal EX User’s Guide” carefully to operate Mobile Terminal EX correctly. Keep the User’s Guide at hand for reference. Please help to recycle lithium-ion and nickel hydride batteries.
Introduction Congratulations on your purchase of Mobile Terminal EX. The User’s Guide describes the guide for handling Mobile Terminal EX and the notes on safe and correct use of Mobile Terminal EX. Read this manual thoroughly before using Mobile Terminal EX. Follow the relevant regulations of the local government for disposal of Mobile Terminal EX. Contact the local government for details.
Safety Precautions The following precautions describes items which should be obeyed for preventing people including users from suffering harms and assets from being lost and enabling users to use Mobile Terminal EX safely. Read the safety precautions thoroughly for safe and correct use of Mobile Terminal EX. Symbols and marks on safety are described below. The marks below indicate influences if the cautions are no kept.
WARNING Do not disassemble or alter the product. Failure to follow it may cause device fault, electric shock or fire to occur. Do not use the product in a place of direct sunlight for a long period, a place of much dust, a place of extremely high moisture, a place with use of water, or a place near a heat generator including hating equipment. Failure to follow it may cause device fault, electric shock or fire to occur.
WARNING Do not use any battery other than the BATTERY PACK (S1596-05/BAT-1004A) exclusively used for the product. Failure to follow it may cause the battery to explode, which would have people get burned or bring fire due to heating. Neither throw the BATTERY PACK, calendar battery and sub-battery used for the product in the fire nor heat, disassemble and short them. Failure to follow it may cause burn, explosion and/or fire to occur.
WARNING If liquid leakage or foreign odor occurs from the BATTERY PACK, move it away from fire immediately. Failure to follow it may cause the leaked electrolytic solution to catch fire, which would burst or set fire to the BATTERY PACK. If you get liquid leaked from the BATTERY PACK into your eyes, do not rub at your eyes but clean them with clean water such as running water. Then get medical attention of a doctor immediately. Leaving your eyes without medical attention may cause them to be troubled.
CAUTION Use the product on the following conditions. Failure to follow it may cause the product to be defected. Operating environment of Mobile Terminal EX Item Temperature Humidity Specification Operating: Non operating: Charging: Operating: Non operating: Charging: 5ºC - 35ºC –20ºC - 60ºC 5ºC - 35ºC 35% - 85%* 35% - 85%* 35% - 85%* * Non-condensing Do not place the product in an area where the temperature changes violently (e.g.
CAUTION Do not operate the product with wet hands. Failure to follow it may cause the product to be defected. Do not put objects on the touch panel for a long time. Failure to follow it may cause the touch panel to be defected. Always press a key on the touch panel or the keyboard with a finger for typing. Pressing a key with a hard and sharp object such as a ballpoint pen may cause the touch panel or keyboard to be defected.
CAUTION Neither put heavy objects on the power and connection cables and the AC adapter nor swathe them with clothes. Failure to follow it may cause electric shock or fire to occur. Neither connect nor disconnect the power cable with wet hands. Failure to follow it may cause device fault or electric shock to occur. Do not use the non-specified voltage. Supplying power of another voltage or frequency to the power cable may cause electric shock, smoking or fire to occur.
Notes on BATTERY PACK, sub-battery and calendar battery. BATTERY PACK contains Lithium-ion battery. Specification of BATTERY PACK Product name and part number: BATTERY PACK (S1596-05 / BAT-1004A) Lithium-ion battery: 7.4V, 2400mAh Characteristics of BATTERY PACK While the BATTERY PACK is charged or supplies power to Mobile Terminal EX, the BATTERY PACK may be heated. This is due to chemical reaction for generating electric energy in the BATTERY PACK but does not indicate the BATTERY PACK is defected.
FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Mobile Terminal EX Preparation 1. Check the items contained in the package you received. Make sure that the items listed in the table below are all contained in the package. If one or more item are missed or damaged, contact your sales agent. Product name Mobile Terminal EX BATTERY PACK ( S1596-05 / BAT-1004A) Sub battery Calendar battery SHOULDER BELT User’s Guide END USER LICENCE AGREEMENT OF MICROSOFT SOFTWARE END USER LICENCE AGREEMENT 2.
Mobile Terminal EX Part Names Liquid crystal display with touch panel Do not push the display firmly or with a sharp object such as a pen. It may damage the display. Volume dial IrDA Adjusts the volume. USB connector communication port DC-IN Battery charge LED Indicates the remaining battery charge in 3 levels. Wireless LAN wave status LED Keyboard Indicates the wireless LAN wave status in 3 levels. Power switch Turns ON/OFF the power.
Specification of Mobile Terminal EX The table below shows the specification of Mobile Terminal EX.
Indicators Item Power lamp Charge lamp Battery charge LEDs Wireless LAN wave status LEDs Power lamp (on rear face) Communication lamp Specification Power OFF (suspend state) Power ON (Remaining capacity of main battery enough) Power ON (Remaining capacity of main battery: 7% or less) Power ON (Remaining capacity of main battery: 3% or less) No charging Charging Charge completed Charge error Remaining battery quantity: 100% - 70% Remaining battery quantity: 69% - 40% Remaining battery quantity: 39% - 8%
Placing the BATTERY PACK 1. Move the safety lock to " 2. Align the grooves at both sides of the BATTERY PACK to the guides on the device body and push the BATTERY PACK. 3. Place the BATTERY PACK and move the safety lock to " ." " (Note: Power cannot be turned on if the safety lock is not in " .") Guide Groove (2) (3) (1) Removing the BATTERY PACK 1. Confirm that the power is turned off (the power lamp is OFF). 2. Move the safety lock to " 3.
Placing or Removing the Sub-battery and the Calendar Battery 1. Confirm that the power is turned off (the power lamp is OFF). 2. Open the sub-battery cover on the rear side of the device by using a coin or the like. 3. Now you can place or remove the sub-battery and/or the calendar battery. Calendar battery Sub-battery cover A coin or the like CAUTION Board side connector Sub-battery The sub-battery and the calendar battery are placed side by side.
Handling the Power Switch The power switch is used to turn on or off the power. A push-type switch is located at the position shown in the figure below. The power switch returns to the original position if you press the power switch and then release it. Pressing the power switch once causes the power to be turned off (suspend) if the power is ON or to be turned on if the power is OFF (resume).
Single Docking Station EX Single Docking Station EX Part Names The names and functions of Single Docking Station EX parts are described below. (1) Insertion port (2) Power lamp (3) Connecting detection lamp (9) Stand (4) Connection terminal (5) Power switch (7) USB connector (8) LAN port (6) AC adapter connector (1) Insertion port Insert Mobile Terminal EX into the port. CAUTION Do not insert any device other than Mobile Terminal EX into the port.
Specification of Single Docking Station EX The specification of Single Docking Station EX is described below. This can be reference for device installation. Outer dimension Weight LAN port USB port Miscellaneous 288×157×130 mm in normal use (288×157×240 mm in connection of Mobile Terminal EX) 288×157×138 mm in use of stand (288×160×245 mm in connection of Mobile Terminal EX) About 1.3 kg Excluding AC adapter 10BASE-T/100BASE-TX ×1 USB2.0 ×4 The bottom stand allows the station to be tilted in two levels.
Lamp Indication Power lamp Connecting detection lamp Power lamp status ON Color Green Blinking Red OFF OFF Status The power of Single Docking Station EX is ON. Connecting Mobile Terminal EX to Single Docking Station EX allows the USB and LAN ports on Single Docking Station EX to be used. In addition, the BATTERY PACK installed in Mobile Terminal EX can be charged. Any of the following states occurs: - Excess voltage is applied to the AC adapter. - Excess current is supplied to Mobile Terminal EX.
Charging the BATTERY PACK by Single Docking Station EX The following describes the procedure and notes on charging the BATTERY PACK installed in Mobile Terminal EX by Single Docking Station EX. 1. Connect the DC plug to the AC adapter connector. 2. Connect the power cable to the inlet of the AC adapter. 3. Insert the power plug of the power cable to an outlet. 4. If you set the power switch to ON, then the power lamp on Single Docking Station EX goes on. 5.
Notes (1) No part of this manual may be reproduced in any form without prior permission. (2) The contents of this manual are subject to change without prior notice. (3) We take all possible measures to create this manual. However, if you feel that any corrections or clarifications should be made to the contents of this manual, please contact your nearest sales representation office. (4) Despite (3) above, we are not responsible for any claims for losses and lost earnings caused by the use of the product.
For inquires, contact: 858-840276-001-A-1