User Manual NCR Orderman Base Station4 Model 7777-RBS Version 01.04 NCR © 2015 All rights reserved.
NCR Orderman Base Station4 User Manual V01.04 General information © 2015 by Orderman GmbH Bachstrasse 59 5023 Salzburg – Austria www.orderman.com We accept no liability for errors or misprints. Copying, even excerpts hereof, is prohibited without the written consent of Orderman GmbH. User Manual NCR Orderman Base Station4 Model 7777-RBS Published February 2015 Version 01.04 Orderman accepts no responsibility for any damage or losses that arise from the use of this manual.
NCR Orderman Base Station4 User Manual V01.04 General information Contents 1 General information ......................................................................................................... 4 1.1 Warranty .............................................................................................................................................. 4 1.2 Labeling ................................................................................................................................
NCR Orderman Base Station4 1 User Manual V01.04 General information General information This manual is intended for use with the NCR Orderman Base Station4 (OBS) Model 7777-RBS. The “NCR Orderman Base Station4” is used for radio transmission, and forms the connecting link between the Orderman handheld radio units and the PC-based POS systems. In this manual, we refer to the “NCR Orderman Base Station4” as the "OBS". 1.
NCR Orderman Base Station4 1.2.2 User Manual V01.04 General information Serial number The serial number is used to uniquely identify the unit. The serial number is located on the model plate. Fig.
NCR Orderman Base Station4 User Manual V01.04 1.3 Safety notices 1.3.1 Explanation of symbols General information Icons and signal words indicate the degree of danger that will result, unless actions to reduce damage are taken. Caution Caution means that minor property damage can occur. Caution is highlighted by horizontal lines above and below the text. Warning Warning means that minor personal injury or serious damage to property can occur.
NCR Orderman Base Station4 User Manual V01.04 NCR Orderman Base Station4 (OMB4) 2 NCR Orderman Base Station4 (OMB4) 2.1 Overview Fig.
NCR Orderman Base Station4 2.2 User Manual V01.04 NCR Orderman Base Station4 (OMB4) Product description The NCR Orderman Base Station4 is specially designed to connect with an Orderman secure radio (OSR). The NCR Orderman Base Station4 can be installed in standing position, hanging from a wall or ceiling, or suspended in a false ceiling. 2.
NCR Orderman Base Station4 User Manual V01.04 Installation of the NCR Orderman Base Station4 3 Installation of the NCR Orderman Base Station4 3.1 Preparation 3.1.1 Installing the antenna The antenna is screwed into the housing with a right-hand thread. Turn the antenna in a clockwise direction (using finger force) into the housing until it hits the end stop. It is not necessary to use a tool. Fig. 4: Screwing in the antenna 3.1.
NCR Orderman Base Station4 3.1.3 User Manual V01.04 Installation of the NCR Orderman Base Station4 Removing/replacing the housing cover For connection, i.e. for installation, you must remove the housing cover. It is not necessary to remove the antenna. 3.1.3.1 Removing the housing cover Press on the housing cover with one hand on the opposite side of the cable outlet. Lift the housing cover with a finger at the cable outlet. Fig. 6: Removing the housing cover Cable outlet rderman 3.1.3.
NCR Orderman Base Station4 3.1.4 User Manual V01.04 Installation of the NCR Orderman Base Station4 Uninstalling/installing the mounting plate 3.1.4.1 Uninstalling the mounting plate To remove the mounting plate from the housing, release the two retaining clips by pressing them away from the housing. The mounting plate is released by pressing the retaining clips. Fig. 8: Removing the housing from the mounting plate Housing Retaining clips 3.1.4.
NCR Orderman Base Station4 3.2 User Manual V01.04 Installation of the NCR Orderman Base Station4 Setup The NCR Orderman Base Station4 is designed to be set up indoors. It can be positioned standing, on the wall, overhead (ceiling mount) or suspended in a false ceiling. For optimal radio performance, avoid installation close to metal objects.
NCR Orderman Base Station4 3.2.1 User Manual V01.04 Installation of the NCR Orderman Base Station4 Standing position Rubber nubs on the underside of the mounting plate increase the stability. Fig.
NCR Orderman Base Station4 3.2.2 User Manual V01.04 Installation of the NCR Orderman Base Station4 Wall/ceiling installation For wall/ceiling installation, the mounting plate has 2 mount holes. As the fastening means for concrete masonry Orderman recommends a 6 x 30 mm wall plug and a 4 x 35 mm universal screw with countersunk head. For other masonry, the proper plugs and screws must be used (screw with countersunk head, max. thread diameter of 4.5mm). Fig.
NCR Orderman Base Station4 User Manual V01.04 Installation of the NCR Orderman Base Station4 Note: For the wall and ceiling installation, the mounting surface must be absolutely level. For a wall mount, we recommend you install the mounting plate with the cable outlet point downward. The arrow in the mounting plate must point upward. Fig. 13: Wall installation Arrow (should point upward) 2 mounting holes Cable outlet Note: Turn the screws with care until countersunk.
NCR Orderman Base Station4 3.2.3 User Manual V01.04 Installation of the NCR Orderman Base Station4 Installation in a false ceiling For installation in a false ceiling, clips are provided to compensate for the wedge profile of the housing. The following steps must be followed: Press both distancing strips as shown in the figure until the clips click into place in the counter surface. Break or cut the two retaining clips from the mounting plate with a knife.
NCR Orderman Base Station4 3.3 User Manual V01.04 Installation of the NCR Orderman Base Station4 Cabling The NCR Orderman Base Station4 can only be connected with an Ethernet network. Two RJ45 ports are located on the top of the housing. The port labeled PoE can also be used for power supply via the network (accessory required). Note: If another Ethernet device is connected to the second Ethernet port (ETH), this device cannot be supplied with voltage via the network. Fig.
NCR Orderman Base Station4 User Manual V01.04 4 Operation 4.1 Operation with power supply unit Operation Note: Comply with the operating temperature range (ambient temperature) for the power supply unit. Use only the original power supply unit for the NCR Orderman Base Station4. 4.2 Operation with Power over Ethernet (network-powered) There are two options for using Power over Ethernet: 4.
NCR Orderman Base Station4 5 User Manual V01.04 Cleaning instructions Cleaning instructions Observe the following care tips: Wipe the surface with a damp, soft cloth. Do not use abrasive agents or cloths with a rough surface. Clean the ports: Never clean the sockets with compressed air or pointed objects! Note: Never use alcohol or corrosive liquids to clean the Orderman units.
NCR Orderman Base Station4 6 User Manual V01.04 Technical specifications Technical specifications Function Radio frequency 433 MHz, 915 MHz* Frequency band OBS version 433MHz = 433,150MHz – 434,650MHz OBS version 915MHz = 902,000MHz – 928,000MHz Transmitting power less than 1 mW ERP Power over Ethernet (PoE) IEEE 802.3at-2009 Type 1 (IEEE 802.
NCR Orderman Base Station4 User Manual V01.04 7 Troubleshooting 7.
NCR Orderman Base Station4 7.2 User Manual V01.04 Troubleshooting Factory reset on the OBS Action Press and hold Reset button for 20 seconds Time Status 2 seconds 5 seconds The status indicator lights up blue for 5 seconds 10 seconds The status indicator does not light up for 10 seconds 3 seconds The status indicator lights up white for 3 seconds This triggers the factory reset function.
NCR Orderman Base Station4 8 User Manual V01.04 Country list Country list The NCR Orderman Base Station4 is available in two different frequency versions. Note: Make sure that the right OBS version is installed (see table) to match the country selected. Country OBS Versions European Union 433MHz Switzerland 433MHz Turkey 433MHz Russia 433MHz USA 915MHz Canada 915MHz Note: Use of frequency bandwidths is regulated by federal laws and must be strictly observed.
NCR Orderman Base Station4 9 User Manual V01.
NCR Orderman Base Station4 10 User Manual V01.04 Glossary Glossary F Firmware As firmware refers to the operating software (Operating System) of the electronic devices. H Handheld A handheld in this manual refers to all the versions of Orderman handhelds. L LED (Light-Emitting Diode) LEDs convert electrical energy into very energy-efficient light. LEDs have a very long life. N NCR Orderman Base Station4 (OBS) The NCR Orderman Base Station4 enables users to connect Orderman handhelds to a host system.