WISMO Quik Q2400 series Q2406 and Q2426 Product Specification Reference: WM_PRJ_Q2400_PTS_002 Revision: 004 Date: March 5, 2004 confidential © Page : 1 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Document Information Revision 001 Date 24 Oct 02 History of the evolution Creation (Preliminary version) 002 24 Jan. 03 003 004 14 Apr 03 March 5, 2004 Remove “Preliminary” status. Modification in applicable products list: • Add Q2406D and Q2426D products and Q2406E and Q2426E products • Remove Q2406C and Q2426C products Update sensitivity value for GSM850 and EGSM900 RF bands. Update mechanical drawing.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Contents Document Information...................................................................................................................................................................... 2 Contents.............................................................................................................................................................................................. 3 Caution 6 Trademarks...................................................
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.11 Activity status indication ......................................................................................................... 23 2.12 Analog to Digital Converter (ADC) ......................................................................................... 24 2.13 Audio interface 25 2.13.1 Microphone inputs ........................................................................................................ 25 2.13.1.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 General ................................................................................................................. 52 4.3.1.1 4.3.1.2 Exposure to RF energy......................................................................................... 52 4.3.1.3 Efficient terminal operation ................................................................................... 52 4.3.1.4 Antenna care and replacement .......................................................
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Caution Information furnished herein by Wavecom are accurate and reliable. However no responsibility is assumed for its use. Please read carefully the safety precautions for a terminal based on WISMO Quik Q2400 Series. General information about Wavecom and its range of products is available at the following internet address: http://www.wavecom.com Trademarks Some mentioned products are registered trademarks of their respective companies.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Overview This document defines and specifies the WISMO QUIK Q24x6 Series, available under two GSM/GPRS Class 10 dual-band versions: • Q2406A: E-GSM/GPRS 900/1800 MHz version with 16 Mbits of Flash memory and 2 Mbits of SRAM (16/2). • Q2406B: E-GSM/GPRS 900/1800 MHz version with 32 Mbits of Flash memory and 4 Mbits of SRAM (32/4). • Q2406D: E-GSM/GPRS 900/1800 MHz version with 64 Mbits of Flash memory and 8 Mbits of SRAM (64/8).
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Reference documents [1] WISMO Quik Q2400 Series Customer Design Guidelines WM_PRJ_Q2400_PTS_005 [2] WISMO Quik Q2400 Series Manufacturing Guide WM_PRJ_Q2400_PTS_006 [3] AT Commands Interface Guide WM_ASW_OAT_UGD_004 [4] Wavecom Acceptance and Verification Plan WAVE Plan, Release 1.4 [5] Q2406 or Q2426 delta with the Q2403 WM_PRJ_Q2400_PTS_004 confidential © Page : 8 / 63 This document is the sole and exclusive property of WAVECOM.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 1 General description 1.1 General information WISMO Quik Q24x6 sub-series is a range of self-contained E-GSM/GSM-GPRS 900/1800 or 850/1900 dual-band modules including the following features: • • • • • • • • • • • • 58.4 x 32.2 x 3.9 mm. 2 Watts E-GSM 900/GSM 850 radio section running under 3.6 Volts. 1 Watt GSM1800/1900 radio section running under 3.6 Volts. Digital section running under 2.8 Volts.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 1.2 Functional description Po w er S u p p ly G E N E R A L P U R P O S E C O N N E C T O R RF In t er f ac e RF I/O Co n t r o ller B at t er y M an ag em en t A /D Co n v er t er SIM S u p p ly SIM Co n t r o ller RF CPU FLA S H M em o r y M an ag em en t U n it SRA M C O N N E C T I O N F U N C T I O N S R.T .
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 1.2.1 RF functionalities The Radio Frequency (RF) functionalities comply with the Phase II E-GSM 900/DCS 1800 and GSM 850/PCS 1900 recommendation. The frequencies are: Q2406 • Rx (E-GSM 900): 925 to 960 MHz. • Rx (DCS 1800): 1805 to 1880 MHz. • Tx (E-GSM 900): 880 to 915 MHz. • Tx (DCS 1800): 1710 to 1785 MHz. Q2426 • Rx (GSM 850): 869 to 894 MHz. • Rx (PCS 1900): 1930 to 1990 MHz. • Tx (GSM 850): 824 to 849 MHz. • Tx (PCS 1900): 1850 to 1910 MHz.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 1.3 Firmware WISMO Quik Q24x6 sub-series is designed to be integrated into various types of applications such as handsets or vertical applications (telemetry, multimedia,…). For vertical applications, the firmware offers a set of AT commands to control the module (for further information, refer to document [3]).
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2 Interfaces Note: Some of the WISMO interface signals are multiplexed in order to limit number of pins but this architecture implies some limitation. For example, in case of using SPI bus, 2-wire bus cannot be used. Warning: All external signals must be inactive when the WISMO module is OFF to avoid any damage when starting and allow WISMO module to start correctly. 2.1 General Purpose Connector (GPC) A 60-pin connector, with 0.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.2 Power supply 2.2.1 General description The power supply is one of the key issues in the design of a GSM terminal. Due to the bursted emission in GSM / GPRS, the power supply must be able to deliver high current peaks in a short time. During these peaks the ripple (Uripp) on the supply voltage must not exceed the limits specified in table “Power Supply Voltage” hereafter. In communication mode, a GSM/GPRS class 2 terminal emits 577 µs radio bursts every 4.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Power Supply Voltage VBATT VMIN VNOM VMAX Ripple max (Uripp) 3.3 V (*) 3.6 V 4.5 V (**) 50 mVpp for freq<200 kHz 500 µVpp for freq>200 kHz VDD 3.1 V 4.5 V 100 mVpp (*): This value has to be guaranteed during the burst (with 2.0 A Peak in GSM or GPRS mode). (**): max operating Voltage Stationary Wave Ratio (VSWR) 2:1.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Power consumption in E-GSM/GPRS 900 MHz and GSM/GPRS 850 MHz mode class 10 VBATT+VDD Conditions INOM IMAX During TX bursts @Pcl5 1.60 A peak 1.8 A peak During RX bursts 110 mA peak 115 mA peak Average 1Rx/1Tx @Pcl5 250 mA 300 mA Average 1Rx/1Tx @Pcl8 190 mA 200 mA Average GPRS Cl 10 (3Rx/2Tx) @Pcl5 400 mA 510 mA Average GPRS Cl 10 (3Rx/2Tx) @Pcl8 260 mA 300 mA Average Idle mode 3 mA 7 mA Power Control Level: Pcl5=2 W typ.; Pcl8=0.5 W typ.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.3 Electrical information for digital I/O All digital I/O comply with 3 Volts CMOS. Operating conditions Parameter I/O type Min Max VIL CMOS -0.5 V 0.8 V VIH CMOS 2.1 V 3.0 V VOL 1X 0.2 V IOL = -1 mA 2X 0.2 V IOL = -2 mA 3X 0.2 V IOL = -3 mA VOH Condition 1X 2.6 V IOH = 1 mA 2X 2.6 V IOH = 2 mA 3X 2.6 V IOH = 3 mA confidential © Page : 17 / 63 This document is the sole and exclusive property of WAVECOM.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.4 LCD interface The WISMO Quik Q24x6 sub-series can be connected to a LCD module driver through either a SPI bus or a two-wire interface. 2.4.1 SPI bus The SPI bus includes a CLK signal (SPI_CLK), an I/O signal (SPI_IO) and an EN signal (SPI_EN) complying with SPI bus standard.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.6 Keyboard interface Warning: This interface is not FULLY available with AT commands: An AT command allows to get the input key code (see AT+CMER command description). This code has then to be processed by the application. This interface provides 10 connections: • 5 rows (ROW0 to ROW4), • 5 columns (COL0 to COL4). The scanning is a digital one, and the debouncing is done in the WISMO module. No discrete components like R, C (Resistor, Capacitor) are needed.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.7 Main serial link (UART1) A flexible 6-wire serial interface is available complying with V24 protocol signaling but not with V28 (electrical interface) due to a 2.8 Volts interface. The signals are: • TX data (CT103/TX), • RX data (CT104/RX), • Request To Send (CT105/RTS), • Clear To Send (CT106/CTS), • Data Terminal Ready (CT108-2/DTR), • Data Set Ready (CT107/DSR).
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Warning: The auxiliary serial link (UART2) is not available on Q24x6D and Q24x6E products (version with 64 Mbits of Flash memory). Pin description Signal Pin I/O I/O type Description Multiplexed with number CT103 / TXD2 18 I 3X Receive serial data GPI CT104 / RXD2 20 O CMOS Transmit serial data GPO2 CT106 / CTS2 24 I CMOS Clear To Send GPIO0 CT105 / RTS2 35 O 2X Request To Send GPIO5 2.9 SIM interface 2.9.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Electrical Characteristics Parameter Conditions SIM_DATA VIH IIH = ± 20 µA SIM_DATA VIL IIL = 1 mA SIM_RST, Source current = 20 µA SIM_DATA Min Typ Max 0.7xSIM_VCC Unit V 0.3xSIM_VCC SIM_VCC – 0.1V V V SIM_CLK VOH SIM_RST, SIM_DATA Sink current = -200 µA 0.1 V 2.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.10 General Purpose Input/Output The WISMO Quik Q24x6 sub-series provides: • 6 General Purpose I/O, • 4 General Purpose Outputs, • 1 General Purpose Input. They are used to control any external device such as a LCD or a Keyboard backlight.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 LED status WISMO Quik Q24x6 sub-series status OFF Module in download mode or module OFF ON Permanent Module switched ON, not registered on the network Slow flash Module switched ON, registered on the network LED ON for 200 ms, OFF for 2 s Quick flash Module switched ON, registered on the network, LED ON for 200 ms, OFF communication in progress for 600 ms Signal Pin number I/O I/O type FLASH LED 52 I/O CMOS / 2X Description General Purpose I/O 2.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.13 Audio interface Two different microphone inputs and two different speaker outputs are supported. The WISMO Quik Q24x6 sub-series also includes an echo cancellation feature which allows handsfree function. In some case, ESD protection must be added on the audio interface lines. 2.13.1 Microphone inputs The MIC2 inputs already include the biasing for an electret microphone allowing an easy connection to a handset.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Microphone gain vs Max input voltage (using controller 1*) Transmit Gain (dB) Max Vin (mVrms) +30 43.80 +33 31.01 +36 21.95 +39 15.54 +42 11 +45 7.79 +48 5.51 +51 3.9 (*) for more details, refer to AT commands documentation [3] Microphone gain vs Max input voltage (using controller 2*) Transmit Gain (dB) Max Vin (mVrms) - 6.5 3031 -6.0 2861 … … 0.0 1434 … … +9.5 480 +10.0 454 + 30.3 43.80 + 30.8 41.36 … … + 50.8 4.14 + 51.3 3.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.13.1.2 Main Microphone Inputs (MIC2) The MIC2 inputs are differential ones. They already include the convenient biasing for an electret microphone (0.5 mA and 2 Volts). This electret microphone can be directly connected on these inputs. The impedance of the microphone 2 has to be around 2 kΩ. These inputs are the standard ones for an handset design while MIC1 inputs can be connected to an external headset or a hands-free kit.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.13.2 Speaker outputs 2.13.2.1 Common speaker outputs characteristics The connection can be differential or single-ended but using a differential connection to reject common mode noise and TDMA noise is strongly recommended. Morover in single-ended mode, ½ of the power is lost. When using a single-ended connection, be sure to have a very good ground plane, a very good filtering as well as shielding in order to avoid any disturbance on the audio path.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.13.2.2 Speaker 2 Outputs Pin description 2.13.2.3 Signal Pin # I/O I/O type Description SPK2P 45 O Analog Speaker 2 positive output SPK2N 47 O Analog Speaker 2 negative output Speaker 1 Outputs Pin description 2.13.3 Signal Pin # I/O I/O type Description SPK1P 41 O Analog Speaker 1 positive output SPK1N 43 O Analog Speaker 1 negative output Buzzer Output The buzzer output (BUZ) is a digital one.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.14 Battery charging interface 2.14.1 Hardware description The WISMO module supports one battery charging circuit for Li-Ion batteries. This circuit uses an interface which consists of a current source inputs (CHG_IN) where the constant current has to flow in order to charge the battery. This current value depends on the battery capacity. It is recommended to provide a current equal to the value of the capacity plus 50 mA.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Electrical Characteristics Parameter Min BAT_TEMP resolution CHG_IN Current BAT_TEMP Input signal range Ksps/s 4.7 5.1* Unit bits 90.3 BAT_TEMP Input Impedance ( C ) CHG_IN Voltage (for I=Imax) Typ 10 BAT_TEMP sampling rate BAT_TEMP Input Impedance ( R ) Max kΩ 100 nF 5.5 V 800 mA 2.8 Vpp * To be parametrized as per battery manufacturer 2.14.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.15 ON / ~OFF 2.15.1 General description This input is used to switch ON or OFF the WISMO module. A high level signal has to be provided on the pin ON/~OFF to switch ON the module. The level of the voltage of this signal has to be maintained between 2.4 V and VDD during a minimum of 1 s. This signal can be left at high level until switch OFF. To be able to switch OFF the module, the pin ON/~OFF has to be released.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.15.2 2.15.2.1 Operating sequences Power ON Once the module is supplied by the power source, the application must set the ON/~OFF signal to high to start the module power ON sequence. The ON/~OFF signal must be held for 1 s minimum. After this time, an internal mechanism keeps it on hold. During the power ON sequence, an internal reset is automatically performed by the module for 240 ms (typical). During this phase, any external reset should be avoided.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.15.2.2 Power OFF To properly power OFF the module, the application must set the ON/~OFF signal to low and then send the AT+CPOF command to de-register from the network and switch off the module. Once the « OK » response is issued by the module, the power supply can be switched off.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.17 Reset signal (~RST) 2.17.1 General description This signal is used to force a reset procedure by providing low level during at least 500 µs. This signal has to be considered as an emergency reset only. A reset procedure is automatically driven by an internal hardware during the power-up sequence. This signal can also be used to provide a reset to an external device. It then behaves as an output. If no external reset is necessary this input can be left open.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.17.2 Reset sequence To activate the « emergency » reset sequence, the ~RST signal has to be set to low for 500 µs minimum. As soon as the reset is complete, the AT interface answers « OK » to the application. For this, the application has to send AT↵. If the application manages hardware flow control, the AT command can be sent during the initialisation phase. Another solution is to use the AT+WIND command to get an unsollicited status from the module.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.19 VCC output This output can be used to power some external functions. VCC has to be used as a digital power supply. This power supply is available when the module is ON. Pin description Signal Pin number I/O I/O type Description VCC 40 O Supply Digital supply Operating conditions Parameter Condition Min Max Unit Output voltage I = 10 mA 2.74 2.86 V 10 mA Output Current 2.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2.21.1 RF connections 2.21.1.1 General There are two possible ways to connect an antenna to the module: • The antenna can be directly connected to the module on the "Antenna pad" by using a spring contact. • The antenna can be connected to the module through a coaxial cable. The coaxial cable is connected to both the "Round pad" and the "Ground pad".
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 ZA M a t c h in g c irc u it ZL = 5 0 Oh m Rec eiv er + W ISM O m o d u le Figure 7: Matching circuit The matching circuit is composed by four elements implemented (see figure above) on the module connecting the "Antenna pad" to the "Round pad" (access to the receiver and the transmitter). The four elements of the matching circuit are not yet defined, and depend on each antenna and mechanical integration.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 A n t en n a p a d GN D CM 3 CM 2 ZL = 5 0 Ω CM 1 GN D CM 4 Ro u n d p a d GN D Figure 9: Electrical diagram for the WISMO Quik Q24x6 sub-series 2.21.2 RF performances RF performances are compliant with the ETSI recommendation GSM 05.05.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Q2406 Characteristic Q2426 E-GSM 900 DCS 1800 GSM 850 PCS 1900 Frequency TX 880 to 915 MHz 1710 to 1785 MHz 824 to 849 MHz 1850 to 1910 MHz Frequency RX 925 to 960 MHz 1805 to 1880 MHz 869 to 894 MHz 1930 to 1990 MHz Impedance VSWR Typical gain 50 Ohms Rx max 1.5 :1 Tx max 1.5 :1 radiated 0 dBi in one direction at least confidential © Page : 41 / 63 This document is the sole and exclusive property of WAVECOM.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 3 Technical specifications 3.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Pin # 19 20 Name ROW3 I/O I/O I/O type CMOS/1X Description Keyboard Row Comment GPO2 or O 1X or CMOS General Purpose Output or Aux.serial Link (UART2) Multiplexed CT104/RXD2 * 21 ROW4 I/O CMOS/1X Keyboard Row 22 GPO1 O 3X General Purpose Output 23 COL0 I/O CMOS/1X Keyboard Column GPIO0 or I/O CMOS/2X or CMOS General Purpose I/O or Aux.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Pin # Name I/O I/O type Description (UART1) Comment used 40 VCC O Supply 2.8 V digital supply output 10 mA max.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 2 1 59 60 Figure 10: WISMO Quik Q24x6 sub-series pin position (bottom view) confidential © Page : 45 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 3.2 Environmental Specifications Conditions Temperature range Operating / Full GSM specifications compliant -20 °C to +55 °C Storage -30 °C to +85 °C ENVIRONMENTAL CLASSES TYPE OF TEST STANDARDS STORAGE Class 1.2 TRANSPORTATION Class 2.3 Cold IEC 68-2.1 Ab test -25° C 72 h -40° C 72 h -20° C (GSM900) -10° C (GSM1800/1900) 16 h 16h Dry heat IEC 68-2.2 Bb test +70° C 72 h +70° C 72 h +55° C 16 h Change of temperature IEC 68-2.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 3.3 Mechanical specifications 3.3.1 Physical characteristics The WISMO Quik Q24x6 Series module has a complete self-contained shield. • Dimensions : 58.4 x 32.2 x 3.9 mm external dimensions (except shielding pins) • Weight : <11 g 3.3.2 Mechanical drawings The next page gives the mechanical specifications of WISMO Quik Q24x6 sub-series. confidential © Page : 47 / 63 This document is the sole and exclusive property of WAVECOM.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Insert here mechanical drawing confidential © Page : 48 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 4 Appendix 4.1 Wavecom acceptance test The WISMO Quik Q24x6 sub-series complies with Wavecom standard acceptance test plan (Refer to document [4]). 4.2 GSM Standard and Recommendations The WISMO Quik Q24x6 sub-series is compliant with the following GSM ETSI, 3GPP, GCF and NAPRD03 recommendations for Phase II. Specification Reference Title 3GPP TS 45.005 v5.5.0 (2002-08) Technical Specification Group GSM/EDGE.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Specification Reference Title 8.1.1 Release 1999) 3GPP TS 04.06 V8.2.1 (2002-05) Technical Specification Group GSM/EDGE Radio Access Network; Mobile Station - Base Station System (MS - BSS) interface; Data Link (DL) layer specification (Release 1999) 3GPP TS 04.08 V7.18.0 (2002-09) Technical Specification Group Core Network; Digital cellular telecommunications system (Phase 2+); Mobile radio interface layer 3 specification (Release 1998) 3GPP TS 04.10 V7.1.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 Specification Reference Title Network (PLMN) and the Integrated Services Digital Network (ISDN) or Public Switched Telephone Network (PSTN) (GSM 09.07 version 8.0.0 Release 1999) 3GPP TS 51.010-1 v5.0.0 (2002- Technical Specification Group GSM/EDGE ; Radio Access Network ;Digital cellular telecommunications system (Phase 09) 2+);Mobile Station (MS) conformance specification; Part 1: Conformance specification (Release 5) 3GPP TS 51.011 V5.0.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 4.3 Safety recommendations (for information only) IMPORTANT FOR THE EFFICIENT AND SAFE OPERATION OF YOUR GSM APPLICATION BASED ON WISMO Quik Q24x6 Series PLEASE READ THIS INFORMATION CAREFULLY 4.3.1 RF safety 4.3.1.1 General Your GSM terminal3 is based on the GSM standard for cellular technology. The GSM standard is spread all over the world. It covers Europe, Asia and some parts of America and Africa. This is the most used telecommunication standard.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 a gain of 3 dBi for mobile operation and 7 dBi for fixed operation. Users and OEM integrators must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM must also be provided with labelling instructions. This device contains 900 MHz GSM functions that are not operational in U.S. Territories. This filing is only applicable for GSM 850 MHz and 1900 MHz PCS operations.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 4.3.2.5 Aircraft Turn your terminal OFF before boarding any aircraft. Use it on the ground only with crew permission. Do not use it in the air. To prevent possible interference with aircraft systems, Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your terminal while the aircraft is on the ground. To prevent interference with cellular systems, local RF regulations prohibit using your modem while airborne.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 evaluations of the relevant scientific literature. The design of your Module complies with the FCC guidelines and applicable WARNING: Unauthorized antennas, modifications, or attachments could impair call quality, damage the Module, or result in violation of FCC regulations. Do not use the Module with a damaged antenna. Please contact your local authorized dealer for antenna replacement. Important! Read these safety guidelines prior to using your Module.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 strength to use the Module. Emergency calls may not be possible on all wireless Module networks or when certain network services and/or Module features are in use. Check with your local service provider(s). 4.3.3.6 Service Safety Information Only qualified service personnel are authorized to repair your digital wireless Module and equipment. Use only approved accessories. Contact you sales representative authorized service centers.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 4.4 General Purpose Connector data sheet The next 6 pages are the KYOCERA/ELCO data sheets for the GPC (also available from http://www.avxcorp.com . confidential © Page : 57 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 AVX 1/6 confidential © Page : 58 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 AVX 2/6 confidential © Page : 59 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 AVX 3/6 confidential © Page : 60 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 AVX 4/6 confidential © Page : 61 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 AVX 5/6 confidential © Page : 62 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
WM_PRJ_Q2400_PTS_002 - 004 March 5, 2004 AVX 6/6 confidential © Page : 63 / 63 This document is the sole and exclusive property of WAVECOM. Not to be distributed or divulged without prior written agreement. Ce document est la propriété exclusive de WAVECOM. Il ne peut être communiqué ou divulgué à des tiers sans son autorisation préalable.
