Consulting * Research * Training * Certification Testing Since 1981 Exhibit 9 Freedom II-D with a Research in Motion RIM802D Transmitter DataTAC Modem MIST Inc. FCC ID: O3JF2R802D1 User’s Manual June 2000 APREL Project No.
MIST Freedom II-D (DataTAC) User Manual 1
MIST Freedom II-D Copyright © 1999 MIST Inc. All Rights Reserved. MIST Part Number: DOC9-5.5 Manual Revision: 1.
FCC compliance statement (USA) This device complies with the requirements in Part 15 of the FCC Rules for a Class B digital device.
WARNING: To comply with FCC RF exposure requirements, this unit must be operated with a minimum separation distance of 40mm (1-5/8 inches) between its antenna and a person's body. The user's hand should not be placed directly next to the antenna or at locations on the unit where the antenna is connected, to ensure compliance with FCC RF exposure limits. Industry Canada Certification This device complies with Industry Canada RSS119.
Important safety information Remember to follow any special regulations governing the use of the MIST FREEDOM II-D and always switch it off in areas where radio devices are forbidden, or when it may cause interference or danger. Any safety laws and regulations pertaining to the use of cell phones and two-way radios will likely apply to your use of the POS. We encourage you to follow such laws and regulations at all times.
permitted. Use only those battery types specified in this User’s Guide. The use of any other may disable the POS and may be dangerous. Failure to observe all these instructions will void the Limited Warranty, and may lead to suspension or denial of services to the offender, or legal action, or both.
Table of Contents Introduction …………………………….…………………… 8 At a Glance …………………………………………………... 9 Know your POS Device ………………………………….. 11 Unpack your POS device package …………………..….. 12 Maintenance and Safety Information ………..………..… 13 Power Information …………………………………….……. 15 Connecting to the Serial Port …………………………….. 18 Operating the Integrated Printer...….…………………….. 19 Accessories ………………………………………………….
Introduction Thank you for purchasing MIST FREEDOM II-D. We are confident that the MIST FREEDOM II-D you purchased will meet your exacting world-class quality standards. MIST FREEDOM IID is a small, hand-held, wireless electronic transaction terminal that communicates with a remote host computer via the wireless network. MIST FREEDOM II allows several modem options for communicating to different network systems, such as CDPD, Mobitex, and DataTAC modem.
At a Glance Front View 9
At a Glance Bottom Back View 10
Know your POS Device Antenna: Extend for best performance. Paper Exit: Print Receipts. Paper Feed Button: Load a new paper roll or eject paper roll from the printer. LCD: Displays all the information and status of your device. Power Key: Turns the device ON and OFF. Menu Keys: Scroll through menu features. Function Keys: Fast selection of features in your device. Account Buttons: Choose the checking or saving account. Command Keys: Enter command to your device. Alphanumeric Keys: Enter number inputs.
Unpack your POS device package You should have the following items in your package: MIST If you want to purchase other accessories for your MIST FREEDOM II-M POS device, please visit our Web site 12
www.mistwireless.com, or contact your local sales representative. Maintenance and Safety Information Please avoid exposure to following environment * * * * * excessive heat, or direct sunlight (your device may be permanently damaged by extended exposure to direct sunlight.) excessive cold (please keep your device between 0°C and 40°C) excessive electrical noise (such as mobile phone, motors and modem.
Maintenance and Safety Information And please avoid the following actions. * * * * * Immersing the device in water. Opening the device or replace any component. (You will loose your software.) Using the device with a damaged antenna. (If your device has any problem, you must contact your local sales representative or technical support immediately.) Keep all flames, sparks, and lit smoking materials away from the battery.
Power Information Battery MIST FREEDOM II-D use NiMH 7.2V, 6AA Battery Pack. (Please use only batteries provided by MIST.) Battery Installation 1. Pull the battery door downward to open. 2. Insert the battery in the device. (Ensure the metal contacts touch) 3. Close the battery door.
Power Information Battery Maintenance - New battery’s full performance is achieved only after two or three complete charge and discharge cycles. - Keep the devices and batteries clean and dry. - Protect against a short circuit when the battery is not installed in the device. - If the device will not be used for and extended time, take the battery out of the device. - All rechargeable batteries have a limited life.
Power Information DC Adapter MIST FREEDOM II-D can also use 9V, 1A Output Unregulated DC Adapter. *Please use only adapters provided by MIST. Use of other power sources may result in damage to your unit. Using the DC Adapter and the Internal Charger Using the DC Adapter, you can plug your POS device directly into a power supply and charge attached batteries. If you turn off the device, the internal charger will charge the batteries automatically. If you turn on the device, charging will take more time.
Connection Connecting to the Serial Port Plug the Serial Cable into the Serial Port on the bottom of the device, and plug the other end of the Serial Cable into the peripheral in use. * When unplugging the Serial Port from the device, please press the Release Tabs to release the hooks.
Operating the Integrated Printer Integrated Thermal Printer MIST FREEDOM II-D integrates a thermal printer for the user to print receipt. 1. Press Paper Feed Button (on the top of the Display) to make the printer sensor standby 60 sec for paper insert. 2. Open the Paper Door at the back of the device.
Operating the Integrated Printer 3. Insert the paper in the gap of the paper entrance. 4. The sensor will feed the paper in the printer automatically. - Make sure that the paper is overted as shown above as the thermal paper will work only in one direction. (If you do not see any printing, the paper is in backwards, re-insert the other way around.) - Do not try to pull paper through the printer manually.
Accessories MIST Inc. provides a useful accessory for your MIST FREEDOM II-D. They can help you to improve the efficiency of your work. Vehicle Charger MIST Freedom II can be charged in vehicle with a Vehicle Charger.