NBB Controls + Components GmbH Flexibly designed complete solutions Radio Control Systems – Cable Control Systems – Infrared Control Systems Operating instructions USA/Canada PocketEvo Transmitter Receiver
NBB Controls + Components GmbH 2
Contents General information .................................................................... 4 Transmitter PocketEvo ® ..............................................................
NBB Controls + Components GmbH General information Standard scope of delivery – Transmitter including carrying system – Receiver with integrated mounting holes – Integrated connection cable or adapter cable for receiver The order confirmation and/or delivery note is binding for the actual scope of delivery. Safety information Even if you have already operated radio control systems, always read these operating instructions before commissioning.
Warranty NBB grants a functional warranty of 12 months from the date of sale on all NBB radio control systems (transmitter, receiver, charger). Working hours and material costs are included in the warranty. Shipping costs shall be at the expense of the buyer. Worn parts, relays, rechargeable batteries and batteries are excluded from the warranty.
NBB Controls + Components GmbH Transmitter PocketEvo ® Variations PocketEvo® minor PocketEvo® media PocketEvo® magna PocketEvo® minor-LCD PocketEvo® media-LCD PocketEvo® magna-LCD Type of Push button Proportional (optional 1-, 2- or 3-steps) 6 Edition 06/17
Commissioning > Operating voltage 2.4 V / 3,0 V L oosen the retaining screw of the battery compartment on the back site of the transmitter and remove the cover. Insert 2 fully charged AA 1.2 V NiMH batteries (or 1.5 V batteries) in the battery compartment, close cover and tighten retaining screw. Charge the rechargeable battery c ompletely before initial use. 1. Loosen the retaining screw 2.
NBB Controls + Components GmbH Transmitter PocketEvo ® Operation of the system > Switching the transmitter on and off CDC-key (Customer Data Collection) – The transmitter can only be started with the CDC-key inserted. – If the CDC-key is not present, the display changesbetween “no” and “tA”. – CDC-key contains customer-specific parameters. Design with emergency stop – Unlock the emergency stop pushbutton by turning clockwise to switch on the transmitter. – The transmitter vibrates shortly.
> Channel number During operation the set channel can be displayed by pressing the “Frequency switching” key. For transmitters without an LED display, the information is displayed in the monochrome. Please refer to the technical documents for the exact position of the “On/Horn” and “Frequency switching” buttons. > Battery life warnings The quick blinking of the letters “Lo” in the display shows the end of the battery capacity. From this time the operation of the transmitter is approx.
NBB Controls + Components GmbH Transmitter PocketEvo ® SMP-Technologie – Surface Mounted Push buttons > Changing the Surface Mounted Push buttons – – – – Switch off the transmitter and remove the battery. Unscrew the threaded sleeve with the supplied special key and pull it outwards. Remove the SMP-button from the top. Insert the new SMP-button. Place the threaded sleeve over the SMP push button again and screw it tight. Start teach mode after changing the SMP-buttons (see below).
> Surface Mounted Push buttons teach mode activation with pushbutton and display To activate teach mode, the transmitter must be switched off. 1. Press and hold the “Frequency switching” key. 2. Switch the transmitter on. 3. The letters “tt” appear in the monochrome after 2 seconds. 4. Release the “Frequency switching” key. 5. Push the button all the way down as quickly as possible. If the corresponding push button number appears in the display, the push button can be released again.
NBB Controls + Components GmbH Transmitter PocketEvo ® Meaning error identification 12 LED Figure Reason Solution Error 0 “Er” and “00” No Calibration in Transmitter calibrate Transmitter Error 1 “Er” and “01” Button 1 not present / exchanged / defect / pressed by Power on Install Button / teach Transmitter / get new Button / free Button by Power on Error 2 “Er” and “02” Button 2 not present / exchanged / defect / pressed by Power on Install Button / teach Transmitter / get new Button / fre
Meaning warning identification LED Figure Reason Solution Warning 1 “01” flash Button 1 is near failure status contact NBB Service Warning 2 “02” flash Button 2 is near failure status contact NBB Service Warning 3 “03” flash Button 3 is near failure status contact NBB Service Warning 4 “04” flash Button 4 is near failure status contact NBB Service Warning 5 “05” flash Button 5 is near failure status contact NBB Service Warning 6 “06” flash Button 6 is near failure status contact NB
NBB Controls, Inc. 5909 School Avenue Henrico, Virginia (VA) 23228 Phone: 800 706-4489 (only USA) Phone: +1 804 262-4846 Fax: +1 804 262-0596 sales@nbbcontrols.com www.nbbcontrols.com Headquarter NBB Controls + Components GmbH Otto-Hahn-Straße 3 – 5 75248 Ölbronn-Dürrn GERMANY Fon: +49 7237 999-0 Fax: +49 7237 999-199 sales@nbb.de www.nbbcontrols.de Edition 07/17 · We reserve the right to alter specifications without notice.
