l pr ov a ap al in -F ra ft D Link-5 VHF User Guide ENGLISH lowrance.
l pr ov a All rights reserved. in al ap Copyright © 2012 Navico D ra ft -F Lowrance® is a registered trademark of Navico No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Lowrance Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Lowrance Electronics may find it necessary to change or end our policies, regulations, and special offers at any time.
l pr ov a Section 1 - General Information........................................................................6 D ra ft -F in al ap 1-1 Features..................................................................................................................................................6 1-2 Customizing your Lowrance VHF Radio......................................................................................7 1-3 How to Display and Navigate Menus.............................................
l pr ov a Section 4 - DSC Setup Menu (DSC SETUP).........................................................22 D ra ft -F in al ap 4-1 DSC Setup - Menu Options........................................................................................................... 22 4-2 Enter or View Your USER MMSI (USER MMSI)......................................................................... 22 4-2-1 Enter your MMSI...............................................................................................
l pr ov a Section 6 - Distress Calls...................................................................................40 D ra ft -F in al ap 6-1 Sending a Distress Call................................................................................................................... 40 6-2 Receiving a Distress Call (DISTRESS!)........................................................................................ 41 6-3 Distress Acknowledgement (DISTRESS ACK) or Relay ..............................
l pr ov a ap Section 1 - General Information in al 1-1 Features D ra ft -F Congratulations on your purchase of this Lowrance Link-5 marine band VHF radio.
l pr ov a ap 1-2 Customizing your Lowrance VHF Radio -F in al You can customize the radio to suit your individual preferences. Some preferences can be set directly through the keys as explained in this Section. Other preferences are set up through the built-in menus and these are explained in the other Sections.
l pr ov a in TX al Symbol ap This simulation shows the locations of all the following information symbols: Transmitting. Transmission power. High (HI) 25W or Low (LO) 1W. WX Weather channel. WX ALT Weather Alert. Alarm beeps will sound (US models only). -F HI LO ra ft D Meaning BUSY Receiver busy with an incoming signal. PRI Priority channel is selected. D Duplex operation. Otherwise, blank for Simplex operation. LOCAL Local calling is selected. Otherwise, blank for distance calling.
l pr ov a 1-6 Basic Operation and Key Functions D ra ft -F in al ap All possible keys and their functions are listed here. Note that some of the keys may not be available depending on your Lowrance VHF radio model. 6 Key handset mic Link-5 base station radio Key Function VOL/PWR Volume and Power. Turn clockwise to power on. Continue to turn until a comfortable volume is reached. VOL/PWR will also adjust the settings of an external speaker, if connected. SQL Squelch or Threshold Level.
l pr ov a ap al D ra ft -F in H/L For all other models: The Wx key can be programmed to a weather channel of your choice. Select a channel you wish to use as your weather channel, then press and hold the Wx key for a few seconds. The radio will beep to confirm your choice. You now have quick access to your favourite channel by pressing the Wx key. Transmission Power. (Located on the handset mic). High (HI) 25W or Low (LO) 1W.
l pr ov a Press EXIT to cancel scan mode and return to normal operation. -F in al SELECT ap PUSH TO D ra ft EXIT CALL Enter (ENT). Use ENT when navigating menus, to confirm entries and edits. Escape (ESC). Use EXIT when navigating menus, to clear incorrect entries, to exit from a menu without saving changes, and to back up to the previous screen. DSC Call Menu. Press to enter the DSC Call Menu and make DSC calls. See Section 6. MENU Radio and DSC Setup Menu.
l pr ov a ap Section 2 - The Radio Menu (MENU) in al 2-1 Radio Menu Options (Menu) -F The following options are available through MENU key: Maintain your buddy list. See Section 2-2. LOCAL/DIST Set radio sensitivity. See Section 2-3. BACKLIGHT Set backlight level. See Section 2-4. CONTRAST Set contrast level. See Section 2-4.
l pr ov a ap 2-2 Maintain Your Buddy List (BUDDY LIST) D ra ft -F in al MENU SELECT ►BUDDY LIST LOCAL/DIST BACKLIGHT ▼ Use the Buddy List to store the names and associated MMSI’s of 20 favourite people. Names are stored in the order of entry, with the most recent entry shown first. The following sections show how to add, edit, and delete entries on your BUDDY LIST. Section 5 explains how to call a buddy.
l pr ov a ap 2-2-3 Delete an Entry D ra ft -F in al BUDDY LIST ►MANUAL NEW ALEX TOM TOM EDIT ►DELETE BUDDY LIST MANUAL NEW ALEX ►TOM DELETE BUDDY TOM ►YES NO 1. Select BUDDY LIST. Press ENT to display the list of entries. 2. Scroll down (if required) to the entry you want to delete and press ENT. 3. Select DELETE then select YES. 4. The entry is deleted immediately and the buddy list is displayed again.
l pr ov a ap 2-4-1 Set the Backlighting Level 1. Select BACKLIGHT. 2. Select a comfortable backlight level using + or - to change the setting. 3. Press ENT to enable the setting and return to the menu. D ra ft -F in al BACKLIGHT ▀ ▀ ▀ ▀ LO HI PRESS ENT Note: The DISTRESS key backlighting cannot be switched off. 2.4.2 Set the Contrast Level CONTRAST ▀ ▀ ▀ ▀ LO HI PRESS ENT 1. Select CONTRAST. 2. Select a comfortable contrast level using + or - to change the setting. 3.
l pr ov a 2-5-2 Local Time (TIME OFFSET) al ap The local time can be set by entering the time offset between UTC and local time as follows. SETTING ►TIME OFFSET TIME FORMAT TIME DISPL▼ D ra ft -F in GPS/DATA MANUAL ►SETTING TIME OFFSET ►+01:30 02:30PM LOC 1. Select GPS/DATA, then SETTING. 2. Select TIME OFFSET to enter the difference between UTC and local time. Half hour increments can be used with a maximum offset of ±13 hours. In this example, a difference of +1.
l pr ov a Select GPS/DATA, then SETTING. 2. Select TIME FORMAT. 3. Select 12 Hr or 24 Hr as desired. In this example, 12 hour format has been selected and so the LCD shows the AM or PM suffix. -F in al ap 1. D ra ft 2-5-4 Time Display Options (TIME DISPLAY) If you have entered the time manually as described in the previous sections, the time is always shown on the screen with the prefix M.
l pr ov a 2-5-7 GPS Alert Options (ALERT) -F in al ap The GPS alert is usually set to ON (on) so that if the GPS navigation receiver is disconnected, the alarm sounds. D ra ft SETTING LL DISPLY ▲ COG/SOG ►GPS ALERT GPS ALERT ON ►OFF 1. Select GPS/DATA, then SETTING. 2. Select GPS ALERT. 3. Select ON (on) or OFF (off ) as desired. 2-6 GPS Simulator (SIMULATOR) The GPS Simulator is set to OFF whenever the radio is switched ON, or whenever real GPS data is available through the COM port.
l pr ov a ap Section 3 - Radio Setup Menu (RADIO SETUP) in al 3-1 Radio Setup Menu (RADIO SETUP) D ra ft -F The following options are available through MENU key: Channel band. UIC * See Section 3-2. CH NAME Edit or delete channel names. See Section 3-3. RING VOLUME KEY BEEP Set the volume level of the incoming call notification beeps. See section 3-4. Set the volume level of the beeps. See section 3-4. INT SPEAKER Switch ON/OFF (on/off ) the radio’s internal speakers. See section 3-5.
l pr ov a 3-3 Channel Names (CH NAME) -F in al ap The channel charts are listed in Appendix C with their default name tags. CH NAME gives you the option to edit or delete the channel name tags displayed on the screen. D ra ft RADIO SETUP ►CH NAME RING VOLUME KEY BEEP ▼ EDIT CH NAME TELEPHONE CH NAME TELEPHONE 01 TELEPHONE ►EDIT DELETE EDIT CH NAME PHONE1 ►YES NO 1. Select RADIO SETUP, then CH NAME. 2.
l pr ov a 1. INT SPEAKER ►ON OFF -F in al ap RADIO SETUP RING VOLUM▲ KEY BEEP ►INT SPEAKE▼ 2. Select RADIO SETUP, then INT SPEAKER. Select ON (on) or OFF (off ) then press ENT to enable the setting and return to the menu. D ra ft 3-6 Set the Priority Channel (WATCH MODE) For EU models, watch mode is similar to a dual watch, scanning between the priority channel CH16 and the working channel.
l pr ov a ap Section 4 - DSC Setup Menu (DSC SETUP) in al WARNING D ra ft -F A valid USER MMSI must be entered into this radio before these DSC functions can be used. See below for instructions on how to Enter Your USER MMSI (USER MMSI). 4-1 DSC Setup - Menu Options The following options are available through MENU key: Enter or view your user MMSI. See section 4-2. USER MMSI (If you do not have a user MMSI, see Appendix D.) Enter or change the name and/or details of a group.
l pr ov a Select DSC SETUP, then USER MMSI. 2. If this is the first time that you are entering your user MMSI, a dashed line appears. ap 1. -F in al Enter your user MMSI along the dashed line using the rotary knob as described in Section 1-4. Press ENT to confirm each correct entry and to move to the next digit. If you make an error, press - until < appears, then press ENT to backup and correct the entry. Press ENT to store your user MMSI. 4.
l pr ov a ap 4-3-2 Edit Group Name Details FISHER1 ►EDIT DELETE EDIT NAME FISHER1 EDIT MMSI 012345678 ra ft -F in al GROUP SETUP MANUAL NEW ►FISHER1 FRIENDS1 FISHER2 012345678 ►STORE CANCEL Select DSC SETUP, then GROUP SETUP. The existing group names are displayed. Press + or - to scroll to the incorrect entry then press ENT. 2. Press ENT to edit. The group name details are displayed, with the cursor at the first character of the name. 3.
l pr ov a 4-5 ATIS MMSI & ATIS Functionality al ap EU models ONLY D ra ft -F in ATIS is only available in certain EU models. You must enter your ATIS MMSI to access ATIS functionality. ATSI must be used if you are navigating inland waterways within Europe. An ATIS MMSI is different to your DSC MMSI. ATIS sends a digital message each time that you release the PTT key. Inland waterways rules require 1 W Tx power on Channels 06, 08, 10, 11, 12, 13, 14, 15, 17, 71, 72, 74 and 77.
l pr ov a 4-5-3 Enable ATIS Functionality (ATIS FUNC) ap ATIS functionality can only be activated if an ATIS MMSI has been entered. See 4-5-1. DSC SETUP INDIV REPL▲ ATIS MMSI ►ATIS FUNC ▼ D ra ft -F in al ATIS FUNC ►ON OFF DSC IS ON 1. Select DSC SETUP, then ATIS FUNC. ATIS Note: It is not possible to have both ATIS ON (on) and DSC ON (on) simultaneously. If you want to activate ATIS, you must first switch DSC off. A note on the LCD will remind you if DSC is already ON.
l pr ov a LL REPLY MANUAL ►AUTO OFF -F in al ap DSC SETUP INDIV REPL▲ DSC FUNC ►LL REPLY ▼ Select DSC SETUP, then LL REPLY. ra ft 1. D 2. Select your response and press ENT to confirm and return to the menu. 4-8 Automatic Channel switching (AUTO SWITCH) When a DSC call is received, it may include a request to change to a specific channel for subsequent communications.
l pr ov a ap 4-9 DSC Test Reply (TEST REPLY) in al You can respond to incoming DSC TEST calls with an automatic response or with a manual response. manual responce is required, press ENT to confirm or press EXIT to cancel. AUTO automatically replies after a 10 second delay with an ACK to any incoming DSC TEST call.
l pr ov a WARNING in al ap Section 5 - Sending and Receiving DSC Calls D ra ft -F A valid USER MMSI must be entered into this radio before these DSC functions can be used. See 4-2 Enter Your USER MMSI (USER MMSI). 5-1 What is DSC? DSC (Digital Selective Calling) is a semi-automated method of establishing VHF, MF, and HF radio calls.
l pr ov a -F in al ap DSC CALL INDIVIDUAL ►LAST CALL GROUP ▼ Note that only three DSC call types can be shown at any one time on the screen. Press + or - to scroll up and down the DSC call types until the cursor is positioned at the desired option. Then press ENT.
l pr ov a ap 5-2-2 Retrying a Routine Call 1. If there is no reply to your call after 30 seconds (UNABLE TO ACKNOWLEDGE) the radio asks if you want to retry the call (SEND AGAIN?). 2. Select YES and press ENT to retry the call. D ra ft -F in al 123456789 SEND AGAIN? ►YES NO The radio will repeat this cycle twice. If the call still cannot be placed, the radio returns to normal operation.
l pr ov a ap 5-2-4 Recall the Most Recent Incoming Call (LAST CALL) BOBBY D INDIVIDUAL ROUTINE 10:22 UTC BOBBY D INDIVIDUAL ROUTINE ►SET CHANNEL BOBBY D INDIVIDUAL ROUTINE ►SEND? D ra ft -F in al DSC CALL INDIVIDUAL ►LAST CALL GROUP ▼ This facility is useful and used frequently. 1. Press CALL to enter DSC mode. LAST CALL is automatically selected. Press ENT to display the contact details of the most recent incoming call. 2. Press ENT to recall the caller.
l pr ov a The radio then asks for confirmation of the ALL SHIPS call. Press ENT to send the call. Continue as explained in Section 5-2-1. ap 4. in al 5-2-7 Call using the Call Log (CALL LOG) D ra ft -F DSC CALL GROUP ▲ ALL SHIPS ►CALL LOG ▼ 01 BOBBY D INDIVIDUAL ROUTINE 10:45 UTC BOBBY D ►CALL BACK DELETE BOBBY D INDIVIDUAL ROUTINE ►SET CHANNEL The Call Log contains the contact details for the 20 most recent incoming calls, so that you call any of them again quickly.
l pr ov a ap 5-2-9 Call using the Sent Call Log (SENT CALL) ▲ ▼ 01 BOBBY D INDIVIDUAL ROUTINE 10:12 UTC CALL BACK ►DELETE SAVE MMSI DELETE BOBBY D ►YES NO D ra ft -F in al DSC CALL CALL LOG DIST LOG ►SENT LOG The Call Log contains the contact details for the 20 most recent sent calls, so that you review details of the call. 1. Press CALL to enter DSC mode, then select SENT LOG. Scroll down to the desired sent call details. 2.
l pr ov a 5-2-11 Make a DSC test call (DSC TEST) in al ap You can test your radio’s DSC operation by sending a DSC TEST CALL to a Buddy or other station equipped with a DSC radio. D ra ft -F Note: You should not use a routine DSC call to test your radio and you should minimize the use of the safety channel for test purposes. 5-2-11-1 Send a DSC TEST call 1. Select DSC CALL then DSC TEST. 2.
l pr ov a CALL FROM 123456789 AUTO ACK ▲▼ 00:02 123456789 AUTO ACK IN 10S ▲▼ 00:03 -F in al ap TEST CALL FROM 123456789 ▼ 00:01 D ra ft Note: These additional information screens are available by rotating the CH knob. 4. AUTO ACK IN 10S 10:12 UTC ▲▼ 00:04 IN 10S 10:12 UTC ENT–> ACK ▲▼ 00:05 10:12 UTC ENT–> ACK KEY->SILENCE ▲▼ 00:06 If TEST REPLY is set to MANUAL, a manual responce is required, press ENT to confirm or press EXIT to cancel.
l pr ov a 5-3-1 Receiving an All Ships Call (ALL SHIPS) When you receive notification of an ALL SHIP call, press any key to cancel the alert. The priority level and the user MMSI are displayed on the screen. If the radio recognises the user MMSI as one of your buddies, the buddy’s name is displayed in place of the user MMSI. -F in al ap 1. D ra ft 2. Press ENT to switch to the designated channel immediately or press EXIT to return to the current working channel.
l pr ov a SAFETY FROM TOM AUTO SW OFF ▲▼ 00:15 TOM AUTO SW OFF CH67 REQUEST ▲▼ 00:18 -F in al ap INDIVIDUAL SAFETY FROM TOM ▼ 00:12 D ra ft Note: These additional information screens are available by rotating the CH knob. 2. AUTO SW OFF CH67 REQUEST 10:12 UTC ▲▼ 00:20 CH67 REQUEST 10:12 UTC ENT–> OPTION ▲▼ 00:23 10:12 UTC ENT–> OPTION KEY->SILENCE ▲▼ 00:25 Press ENT for options on how you want to respond to the call.
l pr ov a ap However, If AUTO SWITCH =OFF, then AUTO SW OFF will be displayed and manual channel change is required: D ra ft -F in al GP 012345678 CALL FROM TOM ▼ 00:12 Note: These additional information screens are available by rotating the CH knob. 3.
l pr ov a ap Section 6 - Distress Calls in al WARNING ra ft -F A valid USER MMSI must be entered into this radio before these DSC functions can be used. See section 4-2 Enter Your USER MMSI (USER MMSI). D 6-1 Sending a Distress Call 1. Open the red cover labelled DISTRESS to expose the red Distress key. 2. TO SEND AN IMMEDIATE DISTRESS CALL (Undesignated): HOLD DOWN the DISTRESS key for about 3 seconds, until you see the distress call sending message (DISTRESS CALL SENDING) on the screen.
l pr ov a After the Distress Call is sent, the radio waits for an acknowledgment. 7. The Distress Call is automatically re-sent every 3.5 to 4.5 minutes until a distress acknowledgement is received or press ENT to select OPTIONS: in al ap 6. D ra ft -F DISTRES CALL SENT! WAIT.. ENT–> OPTION RESEND:03:30 OPTION ►RESEND PAUSE ▼ RESEND:03:20 OPTION PAUSE ▲ ►CANCEL RESEND:03:10 Options are: RESEND to resend the Distress call immediately. PAUSE to PAUSE the RESEND countdown timer.
l pr ov a 024’45.342W 10:12 UTC AUTO SWITCH ▲▼ 00:05 10:12 UTC AUTO SWITCH CH16 IN 10S ▲▼ 00:06 -F in al ap 82’50.178N 024’45.342W 10:12 UTC ▲▼ 00:04 D ra ft Note: These additional information screens are available by rotating the CH knob. 2.
l pr ov a 6-4 Acknowledgement of an Distress Relay Individual (INDIV DISTR) al ap US models ONLY -F in When an incoming Individual Distress Relay call is received, the alarm sounds and INDIV DISTR RELAY is displayed. Push +/- or 3CH or SCAN or H/L button or rotate the CH knob to stop the alarm 2. Push +/- button or rotate the CH knob to scroll any further information about the call 3. Press ENT to ACK the call. 4. Or press EXIT to return to standby. D ra ft 1.
l pr ov a ap Section 7 - Installation D ra ft -F in al This Lowrance radio is designed to generate a digital maritime distress call to facilitate search and rescue. To be effective as a safety device, this radio must be used only within the geographic range of a shore-based VHF marine Channel 70 distress and safety watch system. The geographic range may vary but under normal conditions is approximately 20 nautical miles. Installation Options There are two ways to install the radio.
l pr ov a ap Checklist in al The following items should be supplied in the box. Check before starting the installation and contact your dealer if an item is missing. -F Note: An antenna is not provided. Consult your Lowrance dealer for advice if necessary. Mounting gimbal for the VHF radio 2. GPS connection cable 3. Two mounting knobs 4. Microphone bulkhead mount 5. Four countersunk self-tapping screws for the mounting gimbal 6. Four flat screws for the mounting gimbal 7.
l pr ov a Gimbal Installation Hold the mounting gimbal at the chosen location and use a soft pencil to mark the screw hole positions onto the mounting surface. in al ap 1. If you can’t reach behind the mounting surface to attach the nuts, use the self-tapping screws instead of the flat screws shown in the picture. If you’re drilling into fibreglass, use a drill bit smaller than 3/16” (5mm) to drill the pilot holes. D ra ft -F 2.
l pr ov a that will be covered by the radio fascia after installation.) Drill the 4 mounting holes. Remove the installation template and slide the radio into the cavity. 4. Screw each M5x32 screw through the screw hole in the mounting bracket, then attach the stopper. If your bulkhead exceeds 0.51” (13 mm), the stopper can be discarded if necessary. -F in al ap 3. Tighten the M5x32 screws until the radio is held firmly against the rear of the bulkhead. D ra ft 5.
l pr ov a Fix the DSC label al ap CAUTION D ra ft -F in A DSC warning label is supplied with US versions of this radio. To comply with FCC regulations, this warning label must be affixed in a location that is clearly visible from the operating controls of this radio. Make sure that the chosen location is clean and dry before applying this label. Connect the Radio Cables The connectors are on the rear of the base unit, as follows: GPS/COM connector.
l pr ov a Wiring for GPS/COM connector D ra ft Wire Red Orange White Green Yellow Black Blue Grey ap al -F in Pin 1 2 3 4 5 6 7 8 Function Notes No connection (Not used) OUT (+) Program/clone IN (-) IN (+) OUT (-) (To No connection (Not used) No connection (Not used) ) (Not used) (From ) (From ) (Ground) 8 Grey 5 Yellow 2 Orange 4 Green 1 Bare wire 3 White 7 Blue 6 Black Set Up the Radio CAUTION You can’t make any DSC transmissions until you’ve obtained a user MMSI and entered it i
l pr ov a in al ap The Completed Installation D ra ft -F GPS product External speaker GPS / COM NMEA connection cable VHF Antenna External speaker cable Antenna cable Fuse on Red power cable Link-5 Base unit with speaker microphone 50 Lowrance | Link-5 VHF User Guide Black power cable 12 V DC Battery
l pr ov a ap Appendix A - Technical Specifications in al LOWRANCE Link-5 -F GENERAL D ra ft Power Supply: 13.6V DC. Current drain - Transmit 5 A at 25 W Tx / 1.5A at 1W Tx Receive Less than 250 mA in standby Usable channels: International, USA, Canada, Weather (country specific) Mode: 16K0G3E (FM) / 16K0G2B (DSC) PHYSICAL LCD display (viewing): 46 x 26 mm (1.8 x 1.
l Yes - 20 individual and 10 distress DSC mode: Class D (Global) with dual receiver (individual CH70) Standards: ITU-R M.493-12 (US models), EN 300-338-3 (EU models) -F pr ov a Yes Call logs: Yes in al ap Group Call: D ra ft Channel Naming: Tri watch: Yes Favourite channel scan: Yes All scan: Yes User programmable MMSI: Yes MMSI and NAME directory: Yes - 20 numbers & group TRANSMITTER Frequency: 156.025 - 157.
l pr ov a ap Appendix B - Troubleshooting The transceiver will not power up. al 1. -F in A fuse may have blown OR there is no voltage getting to the transceiver. D ra ft a. Check the power cable for cuts, breaks, or squashed sections. 2. b. After checking the wiring, replace the 7 Amp fuse (1 spare fuse is supplied). c. Check the battery voltage. This must be greater than 10.5 V. The transceiver blows the fuse when the power is switched on. The power wires may have been reversed. a.
l pr ov a ap Appendix C - US & ROW VHF Marine Channel Charts -F in al The following channel charts are provided for reference only and may not be correct for all regions. It is the operators responsibility to ensure correct channels and frequencies are used for local regulations. D ra ft C-1 International Channel Chart CH TX (MHz) RX (MHz) MODE TRAFFIC TYPE SHIP TO SHIP SHIP TO SHORE NAME TAG 01 156.050 160.650 D Public Correspondence No Yes TELEPHONE 02 156.100 160.
l pr ov a 156.125 160.725 D Port Operations No Yes 156.175 160.775 D Port Operations No Yes PORT OPS 64 156.225 160.825 D Public Correspondence No Yes TELEPHONE 156.275 160.875 D Port Operations No Yes PORT OPS 66 156.325 160.925 D Port Operations No Yes PORT OPS 67 156.375 156.375 S Commercial, bridge-to-bridge Yes No BRIDGE COM 68 156.425 156.425 S Inter-ship Yes No SHIP-SHIP 69 156.475 156.475 S Port Operations Yes Yes PORT OPS 70 156.
l pr ov a C-2 USA Channel Chart ap TRAFFIC TYPE SHIP TO SHIP TO SHIP SHORE NAME TAG 156.050 156.050 S Port Operations, Selected VTS Areas Yes Yes PORT OPS/VTS 03A 156.150 156.150 S US Government, Coast Guard Yes Yes UNAUTHORIZED 05A 156.250 S Port Operations, Selected VTS Areas Yes Yes PORT OPS/VTS 156.250 06 156.300 156.300 S Inter-ship Safety Yes No SAFETY 07A 156.350 156.350 S Commercial Yes Yes COMMERCIAL 08 156.400 156.
l pr ov a 156.425 69 156.475 S Boat Operations, Recreational Yes No SHIP - SHIP 156.475 S Boat Operations, Recreational Yes Yes 70 156.525 156.525 PLEASURE Digital Selective Calling - DSC ------ ------ 71 156.575 DSC 156.575 S Boat Operations, Recreational Yes Yes PLEASURE 72 73 156.625 156.675 156.625 S Boat Operations, Recreational Yes No SHIP - SHIP 156.675 S Port Operations Yes Yes 74 PORT OPS 156.725 156.725 S Port Operations Yes Yes PORT OPS 77 156.
l pr ov a 156.050 160.650 SHIP TO SHIP TO SHIP SHORE NAME TAG D Public Correspondence No Yes TELEPHONE 156.100 160.700 D Public Correspondence No Yes TELEPHONE 03 156.150 160.750 D Public Correspondence No Yes TELEPHONE 04A 156.200 156.200 S Canadian Coast Guard, SAR Yes Yes CANADIAN CG 05A 156.250 156.250 S Port Operations, VTS in Selected Areas Yes Yes PORT OPS/VTS 06 156.300 156.300 S Inter-ship Safety Yes No SAFETY 07A 156.350 156.
l pr ov a 156.125 156.125 S Canadian Coast Guard Yes Yes CANADIAN CG 64 156.225 160.825 D Public Correspondence, Duplex No Yes TELEPHONE 64A 156.225 156.225 S U.S. Government, Canadian Commercial Yes Fishing Yes UNAUTHORIZED PORT OPS 4 156.275 156.275 S Port Operations Yes Yes 66A 156.325 156.325 S Port Operations Yes Yes PORT OPS 67 156.375 156.375 S Commercial, SAR Yes No COMMERCIAL 68 156.425 156.
l 6 . pr ov a . The letter “A” illuminated by the channel number indicates the Canada channel is simplex. This same channel is always duplex when selecting International. There is no “A” reference for International channels. The letter “B” is only used for some Canadian “Receive only” channels. in al ap 5 D ra ft -F Channel 70 is designated for use exclusively for Digital Selective Calling (DSC), such as Distress, Safety, and Ship Calls. No voice communication is allowed on CH70.
l pr ov a ap Appendix D - EU VHF Marine Channel Charts -F in al The following channel charts are provided for reference only and may not be correct for all regions. It is the operators responsibility to ensure correct channels and frequencies are used for local regulations. For specific channel information for your country, please refer to local authorities. D ra ft D-1 EU International Channel Chart CH TX (MHz) RX (MHz) MODE TRAFFIC TYPE SHIP TO SHIP SHIP TO SHORE NAME TAG 01 156.
l pr ov a 156.125 160.725 D Public Correspondence, Port Op No Yes PHONE-PORTOP 156.175 160.775 D Public Correspondence, Port Op No Yes PHONE-PORTOP 64 156.225 160.825 D Public Correspondence, Port Op No Yes PHONE-PORTOP 156.275 160.875 D Public Correspondence, Port Op No Yes PHONE-PORTOP 66 156.325 160.925 D Public Correspondence, Port Op No Yes PHONE-PORTOP 67 156.375 156.375 S Commercial, bridge-to-bridge Yes No SHIP-SHIP 68 156.425 156.
l pr ov a ap D-2 Inland Waterways Country Specific table - ATIS ON SPECIFIC FOOTNOTES TRANSMITTING FREQUENCY (MHZ) D ra ft -F in CH al For specific channel information for your country, please refer to local authorities. SHIP SHIP-TO-SHIP SHIP-TO PORT NAUTICAL INFORMATION LAND 60 a) 156.025 160.625 x 01 a) 156.05 160.65 x 61 a) 156.075 160.675 x 02 a) 156.1 160.7 x 62 a) 156.125 160.725 x 03 a) 156.15 160.75 x 63 a) 156.175 160.775 x 04 a) 156.2 160.
l a) k) 156.875 156.875 156.9 161.5 x 156.925 161.525 x 156.95 161.55 x 156.975 161.575 x 20 157 161.6 x 80 157.025 161.625 x in 19 al 78 ap 18 a) ra ft -F 79 D pr ov a 77 x 21 a) 157.05 161.65 x 81 a) 157.075 161.675 x 157.1 161.7 x 22 82 l) m) 157.125 161.725 x 23 m) 157.15 161.75 x 83 a) m) 157.175 161.775 x 24 m) 157.2 161.8 x 84 m) 157.225 161.825 x 25 m) 157.25 161.85 x 85 a) m) 157.275 161.875 x 26 m) 157.3 161.
l pr ov a Explanation of specific footnotes in Country Specific table: In the countries mentioned under remark 2, it is strictly prohibited to use this channel. b. This channel is not allowed to be used between Rhine km 150 and km 350. c. In the Netherlands, this channel is used by for its on-scene communications during safety operations on the North Sea, IJsselmeer, Waddenzee, Ooster- and Westerschelde. -F in al ap a.
l pr ov a ap D-3 Special Channels 2 SEND (MHz) TRAFFIC TYPE SHIP TO SHIP SHIP TO SHORE NAME TAG 156.000 UK Coast Guard Users Yes Yes UK COAST GRD M1 157.425 157.850 UK Marina Channel M1 Yes Yes UK MARINA M2 161.425 161.425 UK Marina Channel M2 Yes Yes UK MARINA 31 157.550 162.150 INT’L, Duplex (Holland) No Yes NL MARINA 96H 162.425 162.425 INT’L (Belgium) No Yes BEL G MARINA L1 155.500 155.500 INT’L (Skandinavia) Yes No LEISURE 1 L2 155.525 155.
l pr ov a ap Appendix E - MMSI, FCC and License Information -F in al You must obtain a user MMSI (Marine Mobile Service Identity) and enter it into your radio before you can use the DSC functions. Contact the appropriate authorities in your country. If you are unsure who to contact, consult your Lowrance dealer. D ra ft The user MMSI is a unique nine digit number, similar to a personal telephone number. It is used on marine transceivers that are capable of using DSC (Digital Select Calling).
Printed in China 1177 al in -F pr ov a ap *988-10244-001* ra ft D l
