User's Manual

ManualsBrandsNavico Auckland ManualsElectronicsHALO PULSE COMPRESSION MARINE RADAR

| 13

Hardware mounting | Halo pulse compression radar installation manual

Surface mount: Rear cable connection

6. Position the scanner carefully over the bolt holes so that they are aligned.

7. Place a  at washer and spring washer onto each bolt, as shown.

8. Insert bolts into the drilled holes and locate into the pedestals threaded mounting holes and

tighten securely.

 Note: The torque settings for the mounting bolts are XX Nm – XX Nm (8.9 lb ft – 13.3 lb ft)

9. Connect the 14 pin end of the interconnection cable. Take care to align the connector correctly

to avoid bending the pins. Secure the locking collar by rotating clockwise until it clicks

Draft_08_April_2015

Summary of content (10 pages)

PAGE 1
Surface mount: Rear cable connection 6. 7. 8. Position the scanner carefully over the bolt holes so that they are aligned. Place a flat washer and spring washer onto each bolt, as shown. Insert bolts into the drilled holes and locate into the pedestals threaded mounting holes and tighten securely.  Note: The torque settings for the mounting bolts are XX Nm – XX Nm (8.9 lb ft – 13.3 lb ft) f ra D 20 il_ pr _A 08 t_ 9. Connect the 14 pin end of the interconnection cable.
PAGE 2
Pole or tower mount: Discreet cable connection 1. 2. The interconnection cable can be optionally connected discreetly underneath the pedestal by moving the 14 pin connector at the rear of the pedestal to a bracket underneath the pedestal. Remove the retaining nut and pull back the connector and fly lead. Fit the supplied blanking plug where the connector used to be.  Note: The blanking plug is attached the bracket underneath the pedestal. 3.
PAGE 3
Fitting the antenna to the pedestal 1. Remove the protective cap from the pedestal and the protective label on the antenna that protects the wave guide.  Note: The protection label and waveguide cover is in place to prevent contaminants from entering the waveguide. These covers MUST BE REMOVED IMMEDIATELY PRIOR TO INSTALLING THE ANTENNA TO THE PEDESTAL.  Note: An antenna Sealing Ring is located under this label in the antenna waveguide chamber.
PAGE 4
Wiring 5 ! Warning: SAFETY SWITCH. The pedestal unit has a safety switch, which removes power from the radar and disables the antenna rotating during maintenance and service. Make sure switch is set to off before commencing installation and back to ON after completion 1. 2. 3. 4. All wiring connections are made inside the RI-12 interface box.
PAGE 5
RI-12 connections D 6 12 3 4 7 8 5 9 10 f ra t_ Name Description 1 2 FUSE Power control: REMOTE 25 Amp blade fuse Remote power control activation jumper. Move to REMOTE position so radar power state is controlled by a multifunction display or switch (see “Remote power control” on page 22) Radar will turn on when power is applied to the main power connector. Remote power wire on AUX IN port is ignored Phoenix connector: Provides 36 V DC up to the pedestal and power for the park brake.
PAGE 6
LED Indicator lights LED Power Color Green steady Comms Status Green flashing Green steady Indication Power is applied and the radar is turned on (by either remote power on or power control jumper set to Auto).
PAGE 7
PinWire color out Scanner connector 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Cable connector Diameter = 23 mm Black Red Yellow Drain N/A Blue White / Blue White / Brown Brown White / Green N/A White / Orange Green Orange Pedestal power DC (-) Pedestal power DC (+) Tinned wire N/A RJ45 Pin 4 RJ45 Pin 5 RJ45 Pin 7 RJ45 Pin 8 RJ45 Pin 3 N/A RJ45 Pin 1 RJ45 Pin 6 RJ45 Pin 2 D RJ45 Connector pinout P1 f ra P8 _A 08 t_ Pin Color 1 2 3 4 White/Orange Orange White/Green Blue 5 6 7 8 White/Blue Green Whit
PAGE 8
Connecting power 1. 2. 3. 4. 5. Strip away approximately 10 mm (0.4” ) of the insulation at the end of each core of the power cable Unscrew the retention screw from the positive input connector (identified by the + sign) on the radar processor Insert the bare end of the positive wire into the positive power cable input connector to make a connection Tighten the holding screw to hold the positive wire in place.
PAGE 9
Grounding requirements The RI-12 has a chassis ground terminal on the underside of the case. The chassis ground is DC isolated from power (–ve) to eliminate the risk of galvanic corrosion.
PAGE 10
Remote power control Remote power control is a feature that allows the power state of the radar to be controlled either from a switch or when a compatible multifunction display is powered on or off.  Note: The power control jumper must be moved from AUTO to REMOTE for the radar to use the remote power on function.