BHM 11/21/17 NTV-DOC242 3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com AUDI DYNAMIC-INT NTV-KIT700 Overview The AUDI-DYN INT Kit interfaces a backup camera (with dynamic guidelines) and one additional video input (front cam, etc) to the factory media screen in select Audi vehicles with the Concert media system (MMi controls on vertical radio face, not console).
BHM 11/21/17 NTV-DOC242 Interface Connectors Power/CAN OUOUT Not Used OUOUT LVDS-OUT LVDS-IN HDMI Cable from HD-LINK RGB IN Not Used Dip Switches Dip Switch Settings Dip SW: UP DOWN 1 Skips RGB Enables RGB 2 Skips V1 Enables V1 3 Skips V2 Enables V2 4 RVC OFF 5 N.C. 6 N.C. 7 N.C. 8 N.C. RVC ON N.C. N.C. N.C N.C.
BHM 11/21/17 NTV-DOC242 AUDI-DYN-INT Installation ATTENTION INSTALLER: All connections (including CAN) must be made BEFORE connecting the power harness to this unit for proper startup operation. 1. Remove the factory screen. This requires removing the plastic screen bezel and then (4x) Torx T20 screws. Disconnect the 10-pin harness from the screen and set the screen aside. 2. Remove the factory radio (CD player). Disconnect all harnesses and set the radio aside. 3.
BHM 11/21/17 NTV-DOC242 7. Grab the provided Power/CAN Harness from the AUDI-DYNINT kit.
BHM 11/21/17 NTV-DOC242 8. Install your reverse camera and run signal, power and ground wires up front to the AUDI interface from step 7. 9. Power your camera with an ACC source or the purple 12v reverse output wire (500 mA MAX). Find a solid ground (-) for the camera as well. NOTE: if using KIT381 (AUDI handle cam), cut off the connector and use black wire for ground and red for power. 10. Connect the signal for your camera to the yellow RCA among the Power/CAN Harness labeled ‘CAMERA’. 11.
BHM 11/21/17 NTV-DOC242 Installation Diagram ACC 12v (+) Optional camera input trigger (selectable via OSD menu) *This module only integrates video input, not audio. Audio is only pass through (to outputs) if supplied. Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase.
BHM 11/21/17 NTV-DOC242 Menu Adjustments Before you start: 1. The IR-Eye must be connected, the AV toggle switch must be connected (main harness) 2. Make sure the car’s ignition is on and radio is on 3. You must be in Reverse Camera mode OR AUX Video mode. • Reverse Camera Mode adjusts Reverse Camera Settings • AUX Video Mode adjusts AUX Video Settings 4. Press the OK BUTTON 4 times (while in reverse OR AUX VID mode: press momentary button), then press POWER. 5.
BHM 11/21/17 NTV-DOC242 Adding HD-LINK Adapter (HDMI Input) Follow the instructions below when adding the HDMI adapter (HD-LINK) to enable HDMI input to the OEM screen: 1. Put dip switch #1 in the DOWN position. 2. Activate the ‘NAV INPUT’ by pressing the provided push button (must be connected to module). 3. Once ‘NAV INPUT’ shows on the screen, on the remote press the OK BUTTON 4 times, then press POWER. 4. Navigate to the ‘NAVI’ section. a. Select ‘HDMI-SEL’ b. Choose ‘HD95E’ c.
BHM 11/21/17 NTV-DOC242 AUDI DYN-INT Operation • Once all connections have been properly made, placing the vehicle in reverse will • • show the connected rear camera image with Dynamic Guidelines which correspond with the steering wheel geometry. If a front camera was added and Automatic front-camera switching was turned on, whenever the vehicle leaves reverse (after showing reverse image once) the connected front camera will display for the user-set amount of time (5, 7, 9 or 11 seconds).
BHM 11/21/17 NTV-DOC242 FAQs Q. The unit will not power on, I have no indication of proper operation. A. This module will not power on properly or display anything (reverse image or AUX video IN) until CAN is properly connected. Q. All I see on the display is a black screen (no factory image pass-through). A. Verify the video cables (IN/OUT) are connected at the proper location (at the screen). B. Verify the video cables are seated all the way. C. Verify the Dip Switches are set correctly. Q.
