3950 NW 120th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 ALLGIG-XG Video in Motion, CIM, Rev-Cam, Front-Cam, AV input, DVD video output For: Chrysler, Dodge, and Jeep with MYGIG radio NTV-KIT260 ALLGIG-XG-HS NTV-KIT272 ALLGIG-XG-FT JR, BM, DS 03/01/16 NTV-DOC078 rB7
JR, BM 03/01/16 NTV-DOC078 rB7 Overview Enables Video in Motion (VIM) for both internal DVD and VES Allows Navigation Entry in Motion Enables the “View Video” button on radios that have this button locked out With additional parts from NAV-TV, it will also: Enable Bluetooth and voice recognition on RER radios (ALLGIG MIC) Enable rear view camera input (AV harness & camera) Emulate VES to allow for additional external AV devices (AV harness & AVSW) Allow for the addition of an additional camer
JR, BM 03/01/16 NTV-DOC078 rB7 ALLGIG Operation Video in Motion/Navigation entry in motion: Video from internal DVD or any external video source, including factory VES, can be viewed while vehicle is in drive and moving. All functions of the navigation will be unlocked while in motion as well. There is no user interaction required to enable this feature. *RHB Radios only: Navigation-based speed indication will no longer be available while VIM is active.
JR, BM 03/01/16 NTV-DOC078 rB7 To view the video from this source, press the “VIEW VIDEO” button. Multiple AV sources: If more than 1 AV source is installed, only “VES AUX 1” and “VES AUX 2” should be programmed; turn off “VES DVD”. To properly select the AUX inputs, the AVSW will be required. (See below.) RER & REN radios require DVD Emulation to enable VES. RBZ/RHB radios: Rear DVD does not emulate, only AUX1 & AUX2.
JR, BM 03/01/16 NTV-DOC078 rB7 12v output when camera is forced: (Default ON) Will supply +12v on “OUTPUT 2” whenever camera is forced; this is used to power the front camera. Front view camera: (Default OFF) This feature will allow the unit to switch between a front view camera and rear view camera when forced camera is requested. ** uConnect/Voice Recognition: (Default OFF) Turns on the internal Bluetooth and voice recognition module.
JR, BM 03/01/16 NTV-DOC078 rB7 ALLGIG (camera/video input) Installation IF INSTALLING ONLY A SINGLE REAR CAMERA, PLUG THE CAMERA DIRECTLY INTO THE AV HARNESS. DO NOT PLUG INTO THE ALLGIG MODULE! The vehicle may already have a harness plugged into the AV plug. Connect the AV harness between the radio and factory harness. Multi Camera Installation: * To connect the rear view camera to the radio, the optional AV harness is required (NTVHAR120). 1.
JR, BM 03/01/16 NTV-DOC078 rB7 Single AV source: 1. Plug the external AV source into the “INPUT” RCA’s of the AV harness. 2. Connect the AV harness between the factory wiring harness (if equipped) and the radio. *Note- Only HS radios can emulate AUX 1 & AUX 2. Low Speed radios can only emulate AUX 1. Multiple AV Sources: (Only supported on High Speed radios) When installing multiple AV sources the optional AVSW is required to switch between the sources.
JR, BM 03/01/16 NTV-DOC078 rB7 ALLGIG XG Pinout Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Description 12v (+) Constant Power INPUT 1 (Disables VIM on RHB when 12v applied)* INPUT 2 (not used) INPUT 3 (Force REAR camera) RX (not used) Relay 1 (common) Video OUT to Radio RCA Common Shield CAN HI (Radio side) CAN HI (Car side) Ground (-) OUTPUT 1 (ACC Out @ 1amp) OUTPUT 2 (Forced Cam 12v out @ 1 amp) OUTPUT 3 (12v out when VES AUX2 is selected) TX (not used) Relay 1 (normally open) Video IN Relay 1