User's Manual

ManualsBrandsNational Electronics & Watch ManualsElectronicsGPS Watch with 2.4G HRM; GPS Watch

National Electronics & Watch Co, Ltd.

BC10

M11-1908D GPS watch Instruction Manual

Ref: UI-11-1904-001

Introduction

Thank you for purchasing the GPS watch. This GPS watch is packed with personal Training

features like speed, trip time, laps, etc. GPS can display your current location in an electronic

map. Watch features include 12/24H Time format, Chronograph, World time, 5 daily Alarms, 6

Interval Timers, Run, Run Data, ALTI and HRM modes. This watch can communicate with a

PC to store and review your performance. This watch uses a rechargeable battery that can be

charged through USB port of your PC. It also uses HRM belt with 2.4 GHz technology to

monitor your heart rate for all your HR related information.

Caring for your GPS watch:

Clean your GPS watch and heart rate monitor with a dampened cloth preferably with mild

detergent solution. Wipe dry using a dry cloth. Do not use chemical cleaners and solvents that

may damage plastic components.

Do not store your GPS watch to prolonged exposure to extreme temperatures as this may

result to permanent damage to your unit.

About GPS:

Global Positioning System (GPS) is a satellite- based navigation system made up of a

network of 24 or more satellites. GPS works best in clear weather condition, anywhere in the

world, 24 hours a day. Tall buildings may interfere with GPS accuracy. When 3 satellite

signals are received, the watch will have 2D GPS fixed (Latitude and Longitude). When 4 or

more satellite signals are received, the watch will have 3D GPS Fixed.

Water immersion:

This GPS watch is designed to be water resistant up to 3 ATM. It can resist water pressure up

to 30 meters. After submersion to water, please make sure to wipe dry and air dry the unit

before using or charging.

Caution: This unit is not intended to be used while swimming. Prolonged water submersion

may cause electronic shorting in the unit which may cause minor skin burn or irritation.

Getting Started

Step 1) Know your watch:

Push button location:

Push button Function:

S1 – Start / Lap /

S3 – View / OK

S5 – Stop / Save /

S7 – Mode / Exit

S9 – GPS

S11 – Light

Note: Actual color of the watch and artwork may vary from style to style.

Summary of content (13 pages)

PAGE 1
National Electronics & Watch Co, Ltd. M11-1908D GPS watch Instruction Manual Ref: UI-11-1904-001 Getting Started Introduction Thank you for purchasing the GPS watch. This GPS watch is packed with personal Training features like speed, trip time, laps, etc. GPS can display your current location in an electronic map. Watch features include 12/24H Time format, Chronograph, World time, 5 daily Alarms, 6 Interval Timers, Run, Run Data, ALTI and HRM modes.
PAGE 2
National Electronics & Watch Co, Ltd. Step 2) Charging the Battery: When the battery level becomes very low, the watch will automatically turn OFF the display (blank-screen). Charge the unit for about 4.0 hours before first use. The length of time for a fully charged battery will last depending on the actual usage. It is recommended to regularly re-charge your battery every 1-2 months even if it is not used to maintain good battery condition. Step 3) Acquire Satellite signals: 2.
PAGE 3
National Electronics & Watch Co, Ltd. Step 4) Pair your Heart Rate monitor: Step 5) Go for a Run: The HRM belt is on standby and ready to send data to your watch. Wear the belt directly on your skin just below your breastplate. It should be snug enough to stay in place during your run. 5.1) Using Run mode: 4.1) Push one tab on the strap through the slot in the HRM transmitter. 4.2) Wet both electrodes with a damp cloth on the back of the HRM belt.
PAGE 4
National Electronics & Watch Co, Ltd. 5.4.2) Press S5 to stop after completing your run. 5.4.3) Press and hold S5 again to save your data. Step 6) Download your data to PC: The watch comes with PC software to make communication between your watch and PC easy and enjoyable. Please install the PC software to your PC using the installer provided. The watch is using a USB PC link cable to connect the watch to PC. Run the GPS PC software on your PC.
PAGE 5
National Electronics & Watch Co, Ltd. • Select GPS or MANUAL setting by pressing S1 or S5 and then press S3 to enter. GPS setting: ¾ Select TIME ZONE by pressing S1 or S5 and then press S3 to enter. There are 36 cities to select in this time zone setting. ¾ Select DST ON or OFF by pressing S1 or S5 and then press S3 to enter. ¾ Select 12H or 24H format setting by pressing S1 or S5. Press S3 to enter. ¾ Select M-D or D-M (Month/Day or Day/Month) format setting by pressing S1/S5.
PAGE 6
National Electronics & Watch Co, Ltd. View 4 Æ CHRONO/ Distance / Clock View 5 Æ CHRONO/ Distance / CHRONO View 6 Æ CHRONO/ Distance / Distance Also note that if the GPS is already ON when you enter the RUN mode, the watch will prompt “GPS GO, PACE and the CHRONO time blinks. The power level is displayed with an increment of 10%, from 10% to 100%. In Memory display, the watch will display the remaining hours available in Track memory. If the power level of the battery is low, the GPS cannot be turned on.
PAGE 7
National Electronics & Watch Co, Ltd. ALTIMETER mode: Press S7 from HRM mode to enter ALTI mode. The watch will display the following in succession: Æ SEARCH GPS Æ BATTERY level Æ DATA TRACK MEMORY Æ view 1 of ALTI mode. The power level is displayed with an increment of 10%, from 10% to 100%. In Memory display, the watch will display the remaining hours available in Track memory. If the power level of the battery is low, the GPS cannot be turned on. The watch will display BATT.
PAGE 8
National Electronics & Watch Co, Ltd. • Press S3 to set the Low/High limit of the zone. You can still manually change the value by pressing S1/ S5. • Press S3 to the Zone Alarm ON or OFF. Press S1 or S5 to change setting. • Press S7 to exit. Note: Alert sub-mode, press S3 to enter ALERT function. When alert is set to ON, there will be a beep sound during taking auto lap. When it is set to OFF, there is no beep sound.
PAGE 9
National Electronics & Watch Co, Ltd. Setting the HRM: Press S3 to enter. Press S1/S5 to select HRM zones. Then press S3 again to set Low and High limit of the zone. Press S1/S5 to manually change the value. Press S3 to confirm setting. Press S7 to exit setting. Note: User has also an option to ON or OFF the zone Alarm. HRM LINK: Press S3 to enter. The watch will auto link and will display the Heart rate. Press S7 to exit.
PAGE 10
National Electronics & Watch Co, Ltd.
PAGE 11
National Electronics & Watch Co, Ltd.
PAGE 12
National Electronics & Watch Co, Ltd. 5) Click on the Download Data tab. Data will be automatically downloaded to your PC. If there no proper contact between the USB clip and the watch, an error may occur and the software will prompt you to check the cable. Repeat the downloading after checking the cable. 6) After downloading the data, the software will prompt you to delete all data in the GPS watch. Default option is NO. WARNING! If you select yes, all data in the watch will be deleted.
PAGE 13
National Electronics & Watch Co, Ltd. FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.