R 333 Bayview Avenue Amityville, New York 11701 For Sales and Repairs, (800) 645-9445 For Technical Service, (800) 645-9440 or visit us at http://tech.napcosecurity.com/ (Note: Technical Service is for security professionals only) Publicly traded on NASDAQ Symbol: NSSC © NAPCO 2013 iBridge® Suite Quick Start Installing the IBR-ZREMOTE Z-Wave® Controller, ISEE-WAP Wireless Access Point and the IBR-ITAB Wireless Touchscreen Tablet WI1980B draft .
Overview of the NAPCO iBridge® IBR-ZREMOTE Z-Wave® Controller General Overview The iBridge® IBR-ZREMOTE is a Local and Remote Control Module and ZWave® Controller that allows control of security, video, locking, lighting and climate control from inside or outside your home. Z-Wave devices may be enrolled, removed and formed into a Z-Wave wireless home control network, and also integrated with Napco's iBridge suite of services that includes access to the iSee Video remote video Internet monitoring system.
Wave network previously started by a "primary" controller (from any manufacturer). Note: As the signal strength between the IBR-ZREMOTE controller and its devices is crucial, we recommend all devices be mounted in their final installed locations before they are included into the network. Ordering Information • IBR-ZREMOTE: Bus-Mount Module for remote control, up/download of security system, plus control of Z-Wave devices, lights, locks, thermostats, etc.
Installing the IBR-ZREMOTE Z-Wave® Controller, ISEE-WAP Wireless Access Point and the IBR-ITAB Wireless Touchscreen Tablet The iBridge Suite allows consumers to control their alarm system, Z-Wave devices and video cameras from wireless and wired Touch Screens, Android and Apple devices and from a PC web browser independently or all at the same time from inside the premises or out. This guide will walk you through the steps required to set up a typical system.
CLOSE-UP VIEW CUSTOMER'S BROADBAND CONNECTION (MODEM OR NETWORK) WAN (INTERNET) (CUSTOMER'S PC AND OTHER DEVICES) WAN 4 3 2 1 POWE RESET CUSTOMER'S ROUTER TYPICAL ROUTER REAR PORT ARRANGEMENT 12V/1A WAN 4 3 2 1 ISEE-WAP ISEE-WAP REAR PORTS (DO NOT USE WAN PORT) The system can be installed out of the box without any configuration changes. First ensure the alarm control panel is wired and working with a standard wired keypad as KP ADDR #1 before you continue.
2B. Remove power from the control panel, disconnect the battery wires and replace the EPROM with the new version. 2C. Power up the control panel and reconnect the battery wires. Enter Direct Address Program Mode and Cold Start the control panel (refer to the enclosed programming instructions WI2052 for the procedure). 2D. Download the saved control panel program configuration back into the control panel or create and download new control panel programming. 2E.
5B. The IBR-ZREMOTE keypad address and Keypad Type can be configured in one of three ways: • Use an IBR-ITAB • Use an app on your iPhone, iPad or Android device • Use a Napco GEM-RP1CAe2 or GEM-K1 keypad with a special programming cable USING THE IBR-ITAB If step 4 was completed properly, the IBR-ZREMOTE and ISEE-WAP should have obtained IP addresses and be ready for use.
Repeat the same steps in the section "USING THE IBR-ITAB" above. When finished, disconnect the cable and be sure to reinstall jumper J4. At this point you should have a functioning system and be able to arm and disarm the panel using the IBR-ITAB. The next step is to integrate video cameras (if applicable). STEP 6: ENROLL VIDEO CAMERAS (Optional) If you already have iSeeVideo cameras installed, then jump to the next paragraph "Discovering Cameras" below.
7C. Near the bottom of the screen, click Add / Replace New i/z Remote Device. In the popup that appears, type the unique MAC Address of the IBR-ZREMOTE printed on the label on the jack marked ETHERNET. Type the complete 12-digit code (do not enter dashes). MAC ADDRESS Keypad Selection Click the Keypad selection pull-down menu to select the keypad type of the installation. This should be the same keypad type installed in step 5.
step 7B above, and verify that the image shown at right appears. Verify the system can be armed and disarmed and that the cameras, if installed, are visible. The consumer can change the User Name and Password by accessing the web account. STEP 8 – SECURING THE SYSTEM Up to this point the iBridge system auto-configured using the default Wi-Fi settings.
The word "admin" is now placed in the Please enter password popup, as shown: Tap OK. The following warning popup appears: Tap Yes and the following User Settings menu appears: Tap Tablet, then tap Connection. The following Connection Settings appears: Change the SSID and Key. Tap (1) Change/Create CUSTOM IBRIDGE ISEE-WAP SSID and KEY. Note: The following only needs to be performed once to configure or change the ISEE-WAP. If enrolling a second IBR-ITAB, jump to the next step.
Tap Continue. In the Preferred Network dialog that appears (shown at right), type a new SSID name, ensure the default security protocol is WEP, then type a new secret Key (check Show Password to view the password text as you type). The Key MUST be one word (no spaces) 10 digits in length using only 0-9, A, B, C, D, E or F as digits. DO NOT use the same SSID name and secret Key as the customer's router. Again, do not use spaces! When finished, tap Save.
Configure the Wireless Cameras. Be sure all wireless cameras are powered, then tap (3) Configure Wireless Camera. A confirmation popup appears; tap Yes to proceed (or tap No to exit without saving changes). Wait while the IBR-ITAB searches for all cameras. When finished searching, the IBR-ITAB lists all the discovered cameras by IP address. Tap to select each camera one at a time and tap "Lock" to lock the camera. Exit when complete. Lock Down the ISEE-WAP.
Test the keypad. To ensure the IBR-ITAB is connected with the correct ISEE-WAP, press the Back/Power Button repeatedly until the Home Screen appears, then press the Security button. A screen with your arming choices appears: Arm the system by first pressing AWAY, then press the User Code in the keypad that appears. Ensure the keypad text on the IBR-ITAB matches the keypad text that appears on the standard wired keypad.
NOTES THE FOLLOWING STATEMENT IS REQUIRED BY THE FCC: This equipment generates and uses radio-frequency energy and, if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception.
NAPCO LIMITED WARRANTY NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in materials and workmanship for thirty-six months following the date of manufacture. NAPCO will, within said period, at its option, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
