Smart Contact Sensor FOR WL-ZSPDBPW-MT-01 User Manual ©Nanjing IOT Sensor Technology Co., Ltd. Publication Number: 2015-0407.
Federal Communications Commission (FCC) Compliance Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Federal Communications Commission (FCC) Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
Welcome to use Smart Contact Sensor User Manual ● is the registered trademark of Nanjing IOT Sensor Technology Co., Ltd. All the other trademarks and registered trademarks mentioned in this manual are trademarks or registered trademarks of their respective owners. ●Please read this manual carefully for the proper use of this product. ●Smart Contact Sensor (hereinafter referred to as “this product”) are smart home audio and video products produced by Nanjing IOT Sensor Technology Co., Ltd.
Features ●Support IEEE 802.15.4 ZigBee/SmartRoom protocol. ●Under defense, remotely control door is open or closed, and send real-time monitor status to smart APP. ●Make scene setting by smart APP for linkage with our other devices. ●Alarm with wireless transmission brings about rapid response, high anti-interference, and low rate of false alarm. ●Low consumption, energy saving, and environment friendly for building green human living environment.
Product Parameter IEEE 802.15.
Package List ( Main Body + Base Of Main Body) *1 (Magnetic Part + Base of Magnetic Part)*1 Flat Cross-Recessed Self-Tapping Screw with Pointed Tail (ST3*12)*4 Battery *1 Manual PE Form Tape *2 Manual *1 3 Guarantee Card Guarantee Card *1
Function Illustration Battery Compartment Main Body Base of Main Body SET Key System Indicator Main Body Of Magnetic Part Base Of Magnetic Part 4
Installation Steps Step 1: Separate [Base of Main Body] & [Base of Magnetic Part] from their respective main body as per below illustration.
Step 2: Option 1: Fix [Base of Main Body] on the door frame or window frame. [Base of Main Body] is fastened to the right position of door frame or window frame via 2 pieces of screw. Similarly, fix [Base of Magnetic Part] on the right position of door or window via 2 pieces of screw.
Option 2: Stick this product on the proper flat surface by the equipped PE form tape.Paste PE form tape on the base of product, and then stick the product in the selected place. Notes: Before installation, please keep the selected place tidy and clean. Step 3: Put 1 * CR2 battery into battery compartment of main body.
Step 4: Aim [Main Body] & [Main Body of Magnetic Part] at the respective card slot of main body to fix them.
Join ZigBee Network 1.Before setting, please make sure the gateway (additional purchase) works normally. Ensure that power is supplied to this product, and it is within the effective communication range of the gateway.
CR2 2.Quickly click [Multi-Functional Key] 4 times to apply for joining ZigBee network, and each click is less than 1s. While searching networking, [System Indicator] is flashing. After joining ZigBee network successfully, [System Indicator] is on 2 seconds, and then goes out. 1 2 Quickly click 4 times, and each click is less than 1s. After joining the network successfully, [System Indicator] is on 2 seconds, and then goes out.
CR2 3.Long press [SET Key] 10 seconds. [System Indicator] flashes 4 times, then goes out to restore to factory setting. The default setting for factory setting does not join ZigBee network.
User Guide After setting, user can control the monitor information of this product by smart mobile terminal. Once door frame or window frame is illegally open, this product will send alarm signal to smart mobile terminal so that user can know all to take corresponding measures.
Cautions ●Please do not install this product in the metal cover and other fully closed devices. It may result in network signal interrupt and low performance. ● Take routine tests periodically to find and remove trouble in case of any alarm for stealing. ●Avoid fall or sever collision for product to for fear of damage of internal part and impact on working life of product. ● Wipe the dust on the product by soft cloth. Clean by the corrosive cleansing liquid and other chemical solvent is forbidden.
Trouble Shooting Q: How to deal with it when failed to join ZigBee network? A: Please confirm gateway works normally, and is allowed to add network, and this product iswithineffective communication range. Q: How to handle it when it stays alarming in the early stage of installation? A: Please confirm main body of door contact matches that of magnetic parts, and size difference is within tolerance.
Purchasing Information Product Name Smart Contact Sensor Material & Color WL-ZSPDBPW-MT-01 Item No.
Software Download Option A: Download the latest smart APP by scanning QR code on the package box of this product. Option B: Please visit our official website: http://www.wulian.cc/service.shtml for downloading. Warm prompt: For the first use, please download smart home APP and read user manual carefully. Please pay attention to Wulian information to download the latest APP in time.
Statement: Hereby, Nanjing IOT Sensor Technology Co., Ltd. declares that this device is in compliance with theessential requirements and other relevant provisions of Directive 1999/5/ EC.
Building 11, No.15, Fengji Road, Yuhuatai District, Nanjing (P. C.: 210039) Email: overseas@wuliangroup.com Service Hotline: 400-889-2891 www.wulian.