SVENSKA NEDERLANDS DEUTSCH ITALIANO PORTUGUÊS ESPAÑOL FRANÇAIS Turntable ENGLISH C 558 РУССКИЙ ® Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS ENGLISH PRECAUTIONS Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below. FRANÇAIS ESPAÑOL PORTUGUÊS INSTALLATION 1 Water and Moisture - Do not use this unit near water, such as near a bathtub, washbowl, swimming pool, or the like.
ENGLISH GETTING STARTED WHAT’S IN THE BOX FRANÇAIS Packed with your C 558 you will find • Switch mode power supply (SMPS) with interchangeable plugs • Counterweight • Audio cable connector (RCA-to-RCA lead) • Single adaptor (for single LP’s) • Allen keys 1,5mm and 2mm for possible setting of the tonearm • Stylus pressure gauge • Plastic tool for tonearm bearings • Paper cartridge alignment tool with two null points • Black felt mat for the platter • White cotton gloves РУССКИЙ SVENSKA NEDERLANDS DEU
IDENTIFICATION OF CONTROLS ENGLISH 11 12 9 13 14 FRANÇAIS 2 16 1 6 ESPAÑOL PORTUGUÊS 15 4 3 5 ITALIANO 7 DEUTSCH 8 NEDERLANDS 10 10 SVENSKA 18 РУССКИЙ 1 2 3 4 5 6 7 4 Platter Felt Mat Sub-Platter Motor Pulley Drive Belt Plinth On/Off Switch 19 8 9 10 11 12 13 14 Dustcover Dustcover Hinges Hinge Fasteners Counterweight Tonearm Tonearm Lift Tonearm Rest And Removable Transport Lock 17 15 16 17 18 19 Anti-Skating Adjustment Headshell With Finger Lift Damped Feet RCA Output, Earth Co
PLATTER, SUB-PLATTER, FELT MAT AND DRIVE BELT INSTALLATION ENGLISH SETUP VERTICAL TRACKING FORCE SETTING (VTF) 1 Install sub-platter (3) and drive belt (5). 2 1 5 3 20mN 10mN ESPAÑOL 15mN FRANÇAIS 1 Confirm the exact weight of your cartridge before setting the Vertical Tracking Force (VTF). 2 Push the counterweight carefully towards the rear end of the counterweight support rod. Place the stylus pressure gauge onto the platter. 3 Set the required VTF by lowering the tonearm lift lever.
SETUP ENGLISH FRANÇAIS VERTICAL TRACKING ANGLE SETTING (VTA) ANTI-SKATING FORCE ADJUSTMENT 1 Set the Vertical Tracking Angle (VTA) by putting a record on the platter. 2 When the needle is lowered into the record groove, the tube of the tonearm should be parallel to the surface of the record. If it is not, loosen both hexagonal screws in the tonearm base just enough to allow vertical movement of the arm pillar without force, and slide the arm up or down until it is parallel.
PROBLEM The platter doesn’t turn although the unit is switched on. ENGLISH TROUBLESHOOTING POSSIBLE CAUSE • The unit is not connected to the mains power supply. • No mains power is being delivered at the socket. • The drive belt is not fitted properly or has slipped off. • No signal contact from the cartridge to any of the following - internal tonearm wiring, arm lead, phono box; or to the amplifier. • Faulty plug, broken wire or loose solder joint in the plug/socket connection.
SPECIFICATIONS ENGLISH GENERAL SPECIFICATIONS TURNTABLE Nominal speed 33/45 rpm, manual speed change (78 rpm possible with special pulley) Speed variance 33rpm: < ± 0.50 %, 45rpm: < ± 0.45 % FRANÇAIS Wow and flutter 33rpm: < ± 0.15 %, 45rpm: < ± 0.15 % Signal to noise -68 dB Downforce range 0 - 30 mN Supplied counterweight system Counterweight for cartridges: 5 - 12 g Voltage Universal swith mode power supply 0 - 3.0 grams 15 V DC/0.
www.NADelectronics.com ©2017 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
C 558 Quick Setup Guide https://nadelectronics.com/product/c-558-turntable/ 1. 2. 3. 4. ©2017 NAD ELECTRONICS INTERNATIONAL, A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
