C 316BEE ENGLISH ® Stereo Integrated Amplifier C 316BEE SVENSKA РУССКИЙ Owner’s Manual NEDERLANDS DEUTSCH © NAD C 316BEE v2 ITALIANO ESPAÑOL FRANÇAIS Stereo Integrated Amplifier
IMPORTANT SAFETY INSTRUCTIONS ENGLISH SAVE THESE INSTRUCTIONS FOR LATER USE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT. 1 2 3 FRANÇAIS 4 5 6 7 ESPAÑOL 8 9 ITALIANO 10 11 DEUTSCH 12 NEDERLANDS 13 SVENSKA РУССКИЙ 2 Read instructions - All the safety and operating instructions should be read before the product is operated. Retain instructions - The safety and operating instructions should be retained for future reference.
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. ESPAÑOL THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
IMPORTANT SAFETY INSTRUCTIONS ENGLISH NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this out. FRANÇAIS The materials can be reused in accordance with their markings.
INTRODUCTION It is especially important that sufficient ventilation be provided. If you are contemplating locating the C 316BEE within a cabinet or other furniture, consult your NAD audio/video specialist for advice on providing adequate airflow. NOTES ON INSTALLATION • Place your C 316BEE on a firm, level surface. • Avoid placing the unit in direct sunlight or near sources of heat and damp. • Allow adequate ventilation. • Do not place the unit on a soft surface like a carpet.
IDENTIFICATION OF CONTROLS FRONT PANEL ENGLISH 1 2 8 Stereo Integrated Amplifier C 316BEE FRANÇAIS © NAD C 316BEE v2 3 4 5 ESPAÑOL 1 STANDBY • With the rear panel POWER switch set to ON position, press this button to turn the C 316BEE ON. The Standby LED indicator will turn from amber to blue. Pressing the STANDBY button again returns the unit to standby mode. • The C 316BEE can also be switched ON from standby mode by pressing any of the front panel buttons.
IDENTIFICATION OF CONTROLS ENGLISH FRONT PANEL FRANÇAIS 8 TONE DEFEAT • The TONE DEFEAT switch bypasses the tone control section of the C 316BEE. • If the Tone Controls are not normally used and left in the 12 o’clock position, then it is advisable to switch out the Tone Control section altogether by using this switch. • In the ‘out’ position, the Tone Control circuits are active; pushing the TONE DEFEAT switch ‘in’ bypasses the Tone Control section.
IDENTIFICATION OF CONTROLS REAR PANEL ENGLISH 6 PHONO CD VIDEO AUX 7 TUNER FRANÇAIS MM © NAD C 316BEE v2 1 2 3 4 5 8 ESPAÑOL ATTENTION! Please make sure that the C 316BEE is powered off or unplugged before making any connections. It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections. ITALIANO 1 PHONO INPUT • Input for a turntable.
IDENTIFICATION OF CONTROLS ENGLISH AMP 4 REMOTE CONTROL USING THE AMP 4 REMOTE CONTROL The AMP 4 remote control handset handles the key functions of the C 316BEE. It has additional controls to remotely operate NAD CD Players. It will operate up to a distance of 23ft (7m). When a command from the remote control is received, the Standby LED indicator will blink. 1 2 PHONO 1 ON/OFF: The AMP 4 remote has a separate ON and OFF button. Press the ON button to switch the unit from Standby to operating mode.
REFERENCE TROUBLESHOOTING ENGLISH CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS FRANÇAIS No sound. • Power AC lead unplugged or power not switched ON. • Mute on. • Check if AC lead is plugged in and power switched ON. • Switch off Mute. No sound one channel. • Balance control not centered. • Center Balance control. • Speaker not properly connected or damaged. • Check connections and speakers. • Input lead disconnected or damaged. • Check leads and connections. Weak bass/diffused stereo image.
REFERENCE ENGLISH SPECIFICATIONS All specs are measured according to IHF 202 CEA 490-AR-2008 standard. THD is measured using AP AUX 0025 passive filter and AES 17 active filter. AUDIO SPECIFICATIONS THD (20 Hz – 20 kHz) <0.03 % in 300 ohms at 2 V out Signal-to-Noise Ratio >100 dB (A-weighted, 32 ohms, ref. 2V out, unity gain) Frequency response ±0.3 dB (20 Hz - 20 kHz) Output impedance 68 ohms FRANÇAIS LINE IN/HEADPHONE OUT Continuous output power into 8 ohms and 4 ohms 40W (ref.
www.NADelectronics.com ©2017 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.