SVENSKA NEDERLANDS DEUTSCH ITALIANO PORTUGUÊS ESPAÑOL FRANÇAIS Stereo Integrated Amplifier ENGLISH C 356BEE РУССКИЙ ® Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS ENGLISH SAVE THESE INSTRUCTIONS FOR LATER USE. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO EQUIPMENT. FRANÇAIS ESPAÑOL PORTUGUÊS ITALIANO DEUTSCH NEDERLANDS SVENSKA 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference.
FRANÇAIS THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAYBE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. PORTUGUÊS ESPAÑOL THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
IMPORTANT SAFETY INSTRUCTIONS ENGLISH NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this out. FRANÇAIS The materials can be reused in accordance with their markings.
INTRODUCTION It is especially important that sufficient ventilation be provided. If you are contemplating locating the C 356BEE within a cabinet or other furniture, consult your NAD audio/video specialist for advice on providing adequate airflow. NOTES ON INSTALLATION Your C 356BEE should be placed on a firm, level surface. Avoid placing the unit in direct sunlight or near sources of heat and damp. Allow adequate ventilation. Do not place the unit on a soft surface like a carpet.
IDENTIFICATION OF CONTROLS FRONT PANEL ENGLISH 1 2 3 4 5 6 FRANÇAIS ESPAÑOL 7 8 PORTUGUÊS 1 STANDBY BUTTON: With the rear panel POWER switch set to ON position, press this button to switch ON the C 356BEE from standby mode. The Standby LED indicator will turn from amber to blue. Pressing the STANDBY button again turns the unit back to standby mode. The C 356BEE can also be switched ON from standby mode by pressing any of the front panel buttons.
IDENTIFICATION OF CONTROLS If an external Media Player is connected to the front MP socket (using a 3.5mm stereo plug) while listening to a MP line-level source, the external Media Player will be directly selected with the MP line-level source immediately disconnected. It is recommended to mute the volume or switch to a different input before plugging/unplugging the external Media Player cable. FRANÇAIS MP (MEDIA PLAYER): Selects a line-level source connected to the MP sockets as the active input.
IDENTIFICATION OF CONTROLS REAR PANEL ENGLISH 19 FRANÇAIS ESPAÑOL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 120V Version Model Only PORTUGUÊS ATTENTION! Please make sure that the C 356BEE is powered off or unplugged from the mains power source before making any connections. It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections.
IDENTIFICATION OF CONTROLS 11 PRE OUT 1: The PRE OUT 1 sockets can be used to drive an additional power amplifier. Use a twin RCA-to-RCA lead to connect the left and right “Audio Input” of the Power amplifier or processor to the PRE OUT 1 sockets. Always turn the C 356BEE and associated external power amplifiers OFF before connecting or disconnecting anything to the PRE OUT 1 sockets. The PRE OUT 1 output signal will be affected by the C 356BEE’s volume and tone control settings.
IDENTIFICATION OF CONTROLS REAR PANEL ENGLISH 19 MDC CLASSIC UPGRADE SLOT: Remove cover to install the optional Modular Design Construction (MDC) module. An example of a C 356BEE-compatible MDC Classic module is the PP 375 Phono Preamplifier module. The PP 375 is integrated into the chassis of the C 356BEE, automatically assigned to the DISC input and its level well matched to the other sets of line level input.
IDENTIFICATION OF CONTROLS When a command from the remote control is received, the Standby LED indicator will blink. Note that the indicator may also blink when receiving commands not necessarily for the C 356BEE but for other components in the system. Please refer to previous sections of the manual for a full description of individual functions. 2 DEVICE SELECTOR: A Device Selector button determines only what component the SR 8 will command; it does not perform any function on the C 356BEE.
IDENTIFICATION OF CONTROLS SR 8 REMOTE CONTROL ENGLISH FRANÇAIS CD PLAYER CONTROL (for use with compatible NAD CD Player): Set the DEVICE SELECTOR to “CD” in order to gain access to these buttons. Some of the control buttons below are applicable only to specific NAD CD Player models; check the owner’s manual of your NAD CD Player for control button compatibility. You can also load the applicable NAD code library to this device so that it can be made compatible with your other NAD equipment.
IDENTIFICATION OF CONTROLS ENGLISH SR 8 REMOTE CONTROL USING THE SR 8 REMOTE CONTROL LIBRARY FRANÇAIS The SR 8 can store a different library of default NAD codes for each of its DEVICE SELECTOR “pages.” If the original default library does not control your NAD CD player, DVD player, or other component, follow the procedure below to change the library code. Refer as well to the table below for a list applicable NAD Library Codes with their corresponding NAD models.
REFERENCE TROUBLESHOOTING ENGLISH CONDITION No sound. FRANÇAIS No sound one channel. POSSIBLE CAUSES POSSIBLE SOLUTIONS • Mains power cord unplugged or power not switched ON. • Check if mains power cord is plugged in and power switched ON. • TAPE MONITOR selected. • De-select TAPE MONITOR mode. • Mute on. • Switch off Mute. • Rear PRE OUT/MAIN IN amp links not fitted. • Fit links. • Balance control not centered. • Center Balance control.
REFERENCE ENGLISH SPECIFICATIONS ±5 dB at 10 kHz ±8 dB at 100 Hz Treble Bass ESPAÑOL TONE CONTROLS PORTUGUÊS <0.005 % at 2 V out >106 dB (IHF; A-weighted, ref. 500 mV out, unity gain) >114 dB (A-weighted, ref. 2 V out, Volume maximum) >92 dB (ref. 100 mV out, unity gain) >80 dB >68 dB 22 kohms+ 100 pF >6 Vrms (ref. 0.1 % THD) 80 ohms Source Z + 1 kohm 166 mV (ref. 500 mV out) ±0.3 dB (20 Hz - 20 kHz, Tone defeat ON) ±0.3 dB (20 Hz - 20 kHz, Tone defeat OFF) >10 V (ref. 0.03 % THD) >8 V (ref. 0.
REFERENCE SPECIFICATIONS ENGLISH PHONO SECTION (WITH OPTIONAL PP 375 INSTALLED) FRANÇAIS ESPAÑOL PORTUGUÊS MM/MC IN, PRE OUT Input impedance - MC MM Input sensitivity2 for 80 W in 8 ohms - MC MM Input sensitivity2 for 1 W in 8 ohms - MC MM Input overload - MC MM Gain - MC in - TAPE OUT3 MM in - TAPE OUT THD1 (CCIF IMD, DIM 100) Signal-to-Noise Ratio, IHF A-weighted - MC4 MM5 RIAA response accuracy Infrasonic filter Channel Separation - MC MM
РУССКИЙ SVENSKA NEDERLANDS DEUTSCH ITALIANO PORTUGUÊS ESPAÑOL FRANÇAIS ENGLISH
www.NADelectronics.com ©2013 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.
