NEDERLANDS Owner’s Manual SVENSKA DEUTSCH ITALIANO ESPAÑOL FRANÇAIS Four Channel Power Amplifier ENGLISH C 245BEE РУССКИЙ ®
IMPORTANT SAFETY INSTRUCTIONS ENGLISH Save these instructions for later use. Follow all warnings and instructions marked on the audio equipment. FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA 1 Read instructions - All the safety and operating instructions should be read before the product is operated. 2 Retain instructions - The safety and operating instructions should be retained for future reference.
FRANÇAIS ESPAÑOL CAUTION Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user’s authority to operate this equipment. CAUTION REGARDING PLACEMENT To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) that is equal to or greater than shown below.
IMPORTANT SAFETY INSTRUCTIONS ENGLISH NOTES ON ENVIRONMENTAL PROTECTION At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this out. FRANÇAIS The materials can be reused in accordance with their markings.
INTRODUCTION Bare wires and pin sockets should be inserted into the hole in the shaft of the terminal. Unscrew the speaker terminal’s plastic bushing until the hole in the screw shaft is revealed. Insert the pin or bare cable end into the hole and secure the cable by tightening down the terminal’s bushing. Ensure bare wire from the speaker cables does not touch the back panel or another socket. Ensure that there is only 1/2” (1cm) of bare cable or pin and no loose strands of speakers wire.
IDENTIFICATION OF CONTROLS FRONT PANEL ENGLISH FRANÇAIS 1 2 3 4 ESPAÑOL 1 STANDBY BUTTON: Press this button to switch ON the C 245BEE. The Standby LED indicator will turn from amber to blue. Pressing the STANDBY button again turns the unit back to standby mode. IMPORTANT NOTICE The rear panel POWER switch must be in the ON position for the STANDBY button to activate. ITALIANO 2 STANDBY LED: This indicator will light up amber when the C 245BEE is in standby state.
IDENTIFICATION OF CONTROLS 4 FRANÇAIS 3 ENGLISH REAR PANEL 5 6 7 8 9 10 11 ESPAÑOL 2 2 BRIDGE MODE (applicable to CHANNEL B only): Set the BRIDGE MODE switch to the “ON” position and connect the speaker to the terminals marked “L +” and “R+” ensuring that the “L+” is connected to the “+” terminal of your loudspeaker and the “R+” is connected to the loudspeaker’s “ - ” terminal. Connect the input source to the CHANNEL B IN sockets.
IDENTIFICATION OF CONTROLS REAR PANEL ENGLISH 6 CHANNEL A SPEAKERS (applicable to CHANNEL A only): Connect the right speaker to the CHANNEL A SPEAKERS terminals marked “R +” and “R-” ensuring that the “R+” is connected to the “+” terminal on your loudspeaker and the “R-” is connected to the loudspeaker’s “-” terminal. Connect the terminals marked “L+” and “L-” to the left speaker in the same way.
IDENTIFICATION OF CONTROLS AUTOMATED TURN-ON LOGIC (ATO LOGIC) ENGLISH REAR PANEL FRANÇAIS same manner by which it was activated. In other words, if the C 245BEE is switched ON via a +12V-control signal, it cannot be switched to standby mode via the front panel STANDBY button, it must wait for removal of the +12V-control signal. In practice, you probably would use only one of the methods once your C 245BEE is installed.
REFERENCE TROUBLESHOOTING ENGLISH CONDITION No power. POSSIBLE SOLUTIONS FRANÇAIS • The power cord is disconnected. • Plug the power cord into the wall outlet securely. • C 245BEE at standby mode. • Press front panel STANDBY button to switch ON the C 245BEE. • Rear panel POWER switch not at ON setting. • Set the rear panel POWER switch to ON setting.
REFERENCE ENGLISH SPECIFICATIONS OVERALL SPECIFICATIONS Normal operation Standby power Idle power ESPAÑOL 270 W (ref. 230V AC 50 Hz; 120V AC 60 Hz) <1 W <55 W ITALIANO Power Consumption FRANÇAIS CHANNEL A IN OR CHANNEL B IN, CHANNEL A SPEAKERS OR CHANNEL B SPEAKERS Continuous output power into 8 Ω and 4 Ω (both channels driven) >35 W (ref. rated THD, 20 Hz – 20 kHz) Continuous output power into 8 Ω (Mono, Bridge mode) >70 W (ref. 20 Hz - 20 kHz, <0.
www.NADelectronics.com ©2009 NAD ELECTRONICS INTERNATIONAL A DIVISION OF LENBROOK INDUSTRIES LIMITED All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International. C 245BEE Manual Issue 1.
