Instructions for 1000DX,1000DX-200, 1001DX, 1001DX-200, 1003DX, 1005DX Speedster Please read before use. Register your product at www.mytee.com/help Model # 1000DX & 1000DX-200 p.3 1001DX & 1001DX-200 p.9 1003DX p.15 1005DX p.21 General information p.27 Serial # Form # ADM-Speedster 12-10 13655 Stowe Dr., Poway, Ca.
1000DX & 1000DX-200 SPEEDSTER 1000DX & 1000DX-200 SPEEDSTER® FRONT 10 1 1000DX & 1000DX-200 SPEEDSTER® BACK 11 2 12 3 4 13 5 9 14 6 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 7 16 6. Front vent 7. Bottom handle 8. 5” locking casters 9. Solution tank 10.Recovery lid 11. Recovery tank 12. Push handle 13. Drain valve 14.
1000DX & 1000DX-200 SPEEDSTER 1000DX & 1000DX-200 SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1000DX & 1000DX-200 SPEEDSTER® SWITCHES Vac 1 Vac 2 Pump Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port. Turn on Vac 1, Vac 2 and Pump switches.
1000DX & 1000DX-200 SPEEDSTER 1000DX & 1000DX-200 SPEEDSTER® DUMP VALVE 1000DX & 1000DX-200 SPEEDSTER® FILTER MAINTENANCE INTAKE FILTER Attach the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank. Check and clean solution tank filter daily by twisting off, rinsing with clean water and replacing. 1000DX & 1000DX-200 SPEEDSTER® LOCKING CASTERS MYTEE® SYSTEM MAINTAINER Locking casters help keep the machine remain stationary during use.
Order parts at: www.mytee.com/products/product.php?id=1000DX 6 C D E F Part prices are subject to change.
8 8 6 9 21 22 23 24 21 25 20 26 29 13 16 19 27 12 17 28 7 14 15 7 18 11 33 34 10 36 37 38 to sol tank filter thru B216 (#58) 7 39 9 8 32 35 40 41 to female QD thru AH105-18 (#55) 6 7 42 43 5 31 6 4 3 30 6 6 2 1 5 5 45 4 44 46 48 47 4 to pump "IN" thru B186 (#36) 3 3 46 57 35 56 59 55 9 4 58 49 4 19 47 6 46 5 52 to female QD thru B111 (#52) 53 4 51 to pump "OUT" thru B106 (#54) to pump "OUT" thru B107 (#39) 37 39 21 54
Cord Input Primary L2 GND White Green Black Inline Conn. White Black Black Black SW-DPST E515 Inline Conn. Switch Pressure C322D Inline Conn. White Pressure Pump L2 Green GND L1 Black 1000DX Inline Conn. Green Black SW-DPST E515 Inline Conn. SW-DPST E515 Inline Conn. Vacuum Motor 2 C310 Inline Conn. Vacuum Motor 1 C310 Inline Conn. Inline Conn. Mytee Products 13655 Stowe Dr.
1001DX & 1001DX-200 SPEEDSTER 1001DX & 1001DX-200 SPEEDSTER® FRONT 10 1 1001DX & 1001DX-200 SPEEDSTER® BACK 12 11 2 3 4 13 5 9 14 6 8 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 7 16 6. Front cooling fan 7. Bottom handle 8. 5” locking casters 9. Solution tank 10.Recovery lid 11. Recovery tank 12. Push handle 13. Drain valve 14. Dual power cords 1001DX & 1001DX-200 SPEEDSTER® ITEMS INCLUDED 15 15. Back vent 16.
01DX & 1001DX-200 SPEEDSTER 1001DX & 1001DX-200 SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1001DX & 1001DX-200 SPEEDSTER® SWITCHES Vac 1 Vac 2 Heater 1 Pump Heater 2 Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect. Attach one end of a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port. “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches.
1001DX & 1001DX-200 SPEEDSTER 1001DX & 1001DX-200 SPEEDSTER® BALL FLOAT 1001DX & 1001DX-200 SPEEDSTER® DUMP VALVE An internal ball float automatically turns off the machine’s vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear dump valve. Attach the 45˚ drain elbow to the drain spout in back. Lift up the dump valve and empty the tank.
Order parts at: www.mytee.com/products/product.php?id=1001DX 12 C D E F Part prices are subject to change.
8 8 13 26 32 31 24 25 27 30 23 28 29 7 10 35 36 37 38 35 21 21 39 22 7 34 40 7 20 13 17 to pump "OUT" thru B136 (#51) 14 to female QD thru B103 (#22) 16 44 43 41 42 18 12 19 15 to sol tank filter thru B216 (#67) to heater thru AH156 (#21) 11 6 47 48 49 6 46 51 2 9 10 50 52 8 7 24 6 23 7 4 53 5 3 45 5 5 1 55 56 5 58 57 to pump "IN" thru B186 (#49) 4 4 56 54 5 4 67 50 4 66 68 65 10 22 69 59 44 7 22 56 35 33 6 62
Inline Conn. L1 Black GND L2 Inline Conn. White Cord Input Secondary Entry Location, Bottom or Far Left Green White / Red C322D Heater Switch Black 3-Position E516 Red Black E511 Lamp Heater 2 E511 Lamp Heater 1 Orange SW-DPST E515 Inline Conn. Pressure Switch Black Red Pressure Pump Inline Conn. Green White / Red Inline Conn. L2 Black White Orange / Black Red Vacuum Motor 1 Inline Conn. White Black Green L2 GND Green Vacuum Motor 2 SW-DPST E515 Black Inline Conn.
1003DX SPEEDSTER 1003DX SPEEDSTER® FRONT 1 1003DX SPEEDSTER® BACK 10 11 2 12 3 4 5 13 9 14 6 7 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 17 15 8 16 6. Front cooling fan 7. Prime Valve 8. Pressure Regulator 9. Solution tank 10.Recovery lid 11. Push handle 12. Recovery tank 13. Drain valve 14. Back vent 15. Dual Power cords 1003DX SPEEDSTER® ITEMS INCLUDED 16. 12” Rear wheels 17.
1003DX SPEEDSTER 1003DX SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1003DX SPEEDSTER® SWITCHES Vac 1 Vac 2 Pump Heater 1 2 “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch. To activate heat, use lower right switch. Press to the left for 1,000 watts, press to the right for 2,000 watts.
1003DX SPEEDSTER 1003DX SPEEDSTER® FILTER MAINTENANCE 1003DX SPEEDSTER® BALL FLOAT INTAKE FILTER An internal ball float automatically turns off the machine’s vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear dump valve. Check and clean solution tank filter daily by twisting off, rinsing with clean water and replacing.
Order parts at: www.mytee.com/products/product.
8 8 25 40 41 42 43 24 39 44 20 38 37 19 23 45 46 22 21 6 36 7 34 13 47 32 33 18 7 17 31 30 15 16 35 29 6 28 65 to heater "IN" 6 27 14 13 26 to female QD thru B103 (#6) 48 to pressure gauge thru B136 (#2) 6 36 6 12 6 11 64 49 7 10 14 16 50 63 9 7 52 51 8 53 to vac tank thru B111 (#62) 52 13 to sol tank filter thru B186 (#59) 39 1 49 8 42 52 54 4 5 6 2 67 56 57 5 4 53 3 68 5 4 59 69 to sol tank 39 62 57 to pump
1003DX E511 Lamp Heater 2 E511 Lamp Heater 1 Orange Orange / Black Black Mytee Products 13655 Stowe Dr. Poway, CA Revision: A Size: Legal Number: 0000 92064 Date: 12/7/2010 Time: 10:34:12 AM Sheet 1 of 1 --File: C:\Compaines\GHI\Projects\Mytee Schematics\1003DX\1003DX.SCHDOC Title Heater Switch Black 3-Position Red E516 Red Black SW-DPST E515 Pressure Pump C313 Inline Conn. Red Vacuum Motor 1 Cord Input Secondary Entry Location, Bottom or Far Left White / Red C302 Inline Conn.
1005DX SPEEDSTER 1005DX SPEEDSTER® FRONT 1 1005DX SPEEDSTER® BACK 10 11 2 12 3 4 5 13 9 14 6 7 1. Switch plate 2. 2” Male Cuff-Lynx™ 3. Solution lid 4. Female quick disconnect (QD) 5. Front handle 17 15 8 16 6. Front vent 7. Prime Valve 8. Pressure Regulator 9. Solution tank 10.Recovery lid 11. Push handle 12. Recovery tank 13. Drain valve 14. Back vent 15. Dual Power cords 1005DX SPEEDSTER® ITEMS INCLUDED 16. 12” Rear wheels 17.
1005DX SPEEDSTER 1005DX SPEEDSTER® VAC/SOL HOSE CONNECTIONS 1005DX SPEEDSTER® SWITCHES Vac 1 Vac 2 Pump “On” switches are located on the plate in front of the machine. To use vacuums, turn on Vac 1 and Vac 2 switches. To use pump, turn on Pump switch. Bottom right switch has no use. Attach one end of a solution hose to a wand or other tool, the other end to the Speedster’s® front quick disconnect.
1005DX SPEEDSTER 1005DX SPEEDSTER® FILTER MAINTENANCE 1005DX SPEEDSTER® BALL FLOAT INTAKE FILTER An internal ball float automatically turns off the machine’s vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear dump valve. Check and clean solution tank filter daily by twisting off, rinsing with clean water and replacing.
Order parts at: www.mytee.com/products/product.php?id=1005DX 24 A B C D E F H212 B103 8 9 Part prices are subject to change.
A B C D E F 8 7 95 9 4 8 10 6 11 90 14 94 To vac tank thru B235 (#45) 4 4 93 9 96 To q.d.
Inline Conn. L1 Black GND Green L2 White White / Red Inline Conn. Cord Input Secondary Entry Location, Bottom or Far Left Cord Input Primary Entry Location, Top or Far Right 26 Red Black SW-DPST E515 C313 White Black White / Red Green Inline Conn. Red Vacuum Motor 1 Green L2 Red Black Pressure Pump SW-DPST E515 Black Inline Conn. C302A Inline Conn. Green C302A Inline Conn. Red SW-DPST E515 Inline Conn. 1005DX Red Black Mytee Products 13655 Stowe Dr.
GENERAL INFORMATION Dear Customer: specify the Model and Serial Number when discussing your machine. Congratulations on the purchase of your new Speedster® Extractor. As you are already aware, the scene of the equipment world is becoming more high tech, and we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality and technology. Name Plate The Model and Serial Number of your machine are shown on the name plate located on the inside of the machine.
GENERAL INFORMATION After Use 17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage. 18. When cleaning and servicing the machine, local or national regulations may apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid, alkalines, or other dangerous liquids. 19. Do not leave operating unattended. 1. Before storing machine, drain, rinse and dry tanks and vacuum hose of water and solution. 2.
GENERAL INFORMATION FAQs HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT NOTICE.
repair and/or parts will only be issued upon evaluation and approval from Mytee Products, Inc. 3. When Warranty is approved, the Distributor’s account will be credited for the replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s) to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be credited for any parts sent for this claim.
NOTES 31
Mytee Products Inc. 13655 Stowe Dr. Poway, Ca. 92064 www.mytee.com PH 858.679.1191 F X 858.679.7814 © 2010 Mytee Products Inc. Printed in the U.S.A.
