User Manual IOTPS10101 PRESENCE SENSOR Mysphera S.L. Parque Tecnológico de Valencia Ronda Auguste y Louis Lumiere, 23 – Nave 13, 46980 Paterna (Valencia) info@mysphera.com www.mysphera.com Telf.: +34 96 182 71 77 / Ext. 112 Fax +34 96 182 94 15 MYSPHERA • Ronda Auguste y Louis Lumiere 23, Nave 13 • 46980 Parque Tecnológico de Valencia • Paterna, Valencia • Spain Telf.: +34 96 182 71 77 • info@mysphera.com • www.mysphera.com Pág.
Modified December 2019 © 2019 Mysphera S.L. ("MYSPHERA") all rights reserved. Any type of exploitation and, in particular, the reproduction, distribution, public communication and / or transformation, in whole or in part, by any means, of this document without the prior express written consent of MYSPHERA is prohibited.
Used simbols in this guide: Simbol Description USB. Electric risk. Warnings: • The product label is located on the bottom of the product. • To reduce the risk of fire or electric shock, do not expose the product to rain or moisture. • Do not place open flame sources, such as burning candles on the product, or in its vicinity. • Do not expose this product to dripping or splashing. • This product must be used indoors. It is not designed or tested for outdoor use.
Table of Contents Table of Contents ............................................................................................................. 4 1. Introduction ............................................................................................................ 5 1.1. 2. Package contents ............................................................................................... 5 Product description ...........................................................................................
1. Introduction 1.1. Package contents The package is an installation kit consisting of: • • • • 4 x Presence sensor • Door opening detection sensor • Magnet to match with door sensor 2. Product description The LOCS kit is a support product for the elderly living alone. The system provides peace of mind to family members closest to the elderly through useful and reliable information about the activity detected at home.
- - - Product identifier code: o Start with 3 letters indicating type / family of the product. o Followed by 2 letters indicating the type of interface and / or communication of the product. o Followed by 1 digit indicating version of the enclosures / enclosures / mechanical encapsulation. o Followed by 2 digits indicating the hardware version. o Finishing with 2 digits that indicate the firmware version.
5. Maintenance and cleaning No special cleaning products are needed for cleaning this device. Dampen a cloth with water and run it across the surface. Do not clean the equipment when it is turned on. Do not use solvents. This device does not require special maintenance. Once the AA batteries are exhausted, the 3 batteries must be replaced. To do this, open the battery cover with a screwdriver and replace the 3 AA batteries.
7. Incidents solution 7.1. Usual incidents INCIDENT The device does not turn on. SOLUTION It may be a problem of lack of charge, this will have to open the back cover of the sensor and replace the batteries. If it still does not work, you will have to change the device and take the damaged one to MYSPHERA. INCIDENT When you open the application, one of the sensors does not appear. SOLUTION Contact the installation company to verify if the sensor has been configured correctly.
The company is not responsible for improper use of it and the possible consequences that the product itself or the parts that form it may have. 8.3. Information about radiofrecuency 8.3.1. Radiolectric devices manufacturing Cuadro Nacional Atribución Frecuencias (Spain, Orden ETU/416/2018, 26th April, 2018) https://www.boe.es/diario_boe/txt.php?id=BOE-A-2018-5704 European Frequency Information System (2402 MHz - 2480 MHz) https://www.efis.dk/views2/search-general.
9.3. Updating device The programming and functionality of the hardware and firmware are carried out at the factory complying with the essential requirements of the product. The end user cannot make any modification of the FW / SW or functionality or have any button, connector or element that allows changing any parameter that affects the correct functioning of the product or the fulfillment of its essential requirements.