Owner manual

ManualsBrandsMyron L ManualsToolsPT3

4 5

ULTRAPEN

™

PT3

ORP & Temperature Pen

ACCURATE

RELIABLE

SIMPLE

Visit our we bs ite:

myronl.com/pt3.htm

Professional Water Analysis

•

Accuracy of ±10 mV ORP

•

Proprietary Sensor Design

•

99.9% Pure Platinum Electrode

•

3 Calibration Options with Automatic

Solution Recognition

•

Automatic Temperature Compensation

in Calibration Mode

•

Temperature Readout

•

Waterproof

myronl.com

PACkAgE CONTENTS:

PT3 Pocket Tester Pen - Battery Installed•

Scoop•

Soaker Cap•

Pocket Clip•

Holster•

Lanyard•

ORP Electrode Cleaning Paper •

Operating Instructions•

MADE IN USAMADE IN USA

ORIGINAL

EDITED FOR USE

Minimum height 5 mm

ULTRAPEN™ PT2

pH & Temperature

ULTRAPEN™ PT1

Conductivity, TDS, Salinity

& Temperature

ULTRAPEN™ PT4

Free Chlorine Equivalent

(FC

)

& Temperature

Summary of content (6 pages)

PAGE 1
ULTRAPEN ™ PT3 ORIGINAL ORP & Temperature Pen EDITED FOR USE Minimum height 5 mm S ACCURATE S RELIABLE S SIMPLE Professional Water Analysis Accuracy of ±10 mV ORP Proprietary Sensor Design 99.
PAGE 2
INTRODUCTION Thank you for purchasing the Myron L ULTRAPEN™ PT3 ORP Pen. This instrument is designed to be extremely accurate, fast, and simple to use in diverse water quality applications. Advanced features include highly stable microprocessor-based circuitry; automatic temperature compensation from 15ºC to 30ºC while in calibration mode; user-intuitive design; and waterproof housing. A true one-handed instrument, the PT3 is easy to calibrate and easy to use.
PAGE 3
OPERATING INSTRUCTIONS NOTE: Selecting “ESC” from any menu immediately turns the PT3 off without saving changes. I. Temperature Unit Selection The PT3 allows you to select the type of units used for displaying temperature: °C (Degrees Celsius) or °F (Degrees Fahrenheit). To set the preference: 1. Push and release the push button to turn the PT3 on. 2. Push and hold the button. The display will alternate between “CAL”, “FAC CAL”, “ºCºF TEMP”, “ModE SEL” and “ESC”. 3.
PAGE 4
a. b. In Hold mode when the LED turns on solid, remove the PT3 from solution. The display will alternate between the final ORP and temperature readings. Note the readings for your records. In LIVE mode allow the PT3 to remain in solution while the LED flashes slowly. The display will alternate between live ORP and temperature readings. Note the readings for your records.
PAGE 5
... continued from page 3 1. 2. 3. 4. Push and release the push button. Push and hold the push button. The display will alternate between “CAL”, “FAC CAL”, “ºCºF TEMP”, “ModE SEL” and “ESC”. Release the button when “FAC CAL” displays. The display will alternate between “PUSHnHLD” and “FAC CAL”. Push and hold the push button until “SAVEd FAC” displays indicating the PT3 has been reset to its factory calibration. MAINTENANCE I.
PAGE 6
Specifications Temperature ORP Range: -1000mV to +1000mV 0 - 71°C / 32 - 160°F Accuracy: ± 10mV ± 0.1ºC / ± 0.1ºF Resolution: 1mV ORP 0.1ºC / 0.1ºF Time to Reading Stabilization: 10 - 45 seconds Power Consumption: Active Mode 37mA, Sleep Mode 2µA Temperature Compensation: Automatic In Calibration Mode From 15ºC to 30ºC Physical Dimensions: 17.15cm L x 1.59cm D / 6.75in. L x 0.625in. D Weight: 50.4g / 1.78oz.