X2 Transponder User Manual
Published by: MYLAPS B.V. Zuiderhoutlaan 4 2012 PJ Haarlem The Netherlands Copyright © 2016 No part of this document may be reproduced by any means without the written consent of the publisher. Whilst every care has been taken to ensure that the information in this document is correct, no liability can be accepted by MYLAPS for loss, damage or injury caused by any errors or omissions in this document.
Table of Contents Table of Contents .................................................................................................................................................... 3 1. 2. 3. 4. Introduction ..................................................................................................................................................... 5 1.1. This manual...............................................................................................................................
5.2. 6. Mounting rechargeable model ..............................................................................................................26 Maintenance..................................................................................................................................................27 6.1. Periodic maintenance schedules ...........................................................................................................27 6.2. Cleaning ......................................
1. Introduction 1.1. This manual This user manual describes how to install, use and maintain the X2 Transponder. 1.2. Intended use of the X2 Transponder The main X2 Transponder components (X2 Transponder and X2 RaceKey) are mounted on a car, motorcycle, kart or bike to measure lap times. 1.3. Description of the X2 Transponder and X2 System The track you are racing on has a MYLAPS system installed at the start and finish line and maybe at intermediate points along the track.
2. Safety 2.1. Important safety instructions Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings before operating the X2 Transponder equipment. 1. Clean only with a dry cloth. Do not use liquid cleaners or aerosol cleaners. 2. Do not install equipment near any heat sources, or other equipment that produce heat (the maximum operating temperature should not exceed 140°F/60°C). 3. Never spill liquid of any kind on the equipment. 4.
2.3. FCC compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
3. Description 3.1. Components X2 Transponder X2 RaceKey X2 Transponder Holder USB cable X2 Transponder Manual (Revision 2.
Extra components used for the Direct Power model Transponder to RaceKey mount cable X2 RaceKey to 12VDC power source cable X2 RaceKey mount X2 Transponder Manual (Revision 2.
3.2. Indicator light (LED) signals 3.2.1. X2 RaceKey (when docked on the direct power X2 RaceKey mount) When power is applied, the key will show a startup sequence where all the LED’s will flash. After the start up sequence the indicators will light as described in the table below.
Steady GREEN Steady Red Active Subscription Inactive Subscription Steady GREEN Fully Charged RED Flashing Charging 3.2.3. X2 Transponder Rechargeable The X2 Transponder has an indicator LED in the M8 Connector. LED indicator Transmitting Charging Battery Full Steady GREEN No No Yes Subscription Active Yes Flashing RED once every second Flashing GREEN in a sequence No Yes No Yes Yes No No Yes X2 Transponder Manual (Revision 2.
Flashes RED every 5 seconds Flashes RED 5 times per second Yes No No Yes No See comment See comment No Not lit No No No No Less than 1 day charge left Transponder will charge when connected to power source n/a 3.2.4. X2 Transponder Direct Power The X2 Transponder has an indicator LED in the M8 Connector.
4. How to use the product Your X2 Transponder needs to be registered and activated before you can use it. Otherwise it will stop sending out its transponder number, and the subscription indicator light in the M8 Connector on the X2 Transponder will flash red 5 times per second. During a race, keep the direct power X2 RaceKey in its mount to ensure the X2 Transponder stays activated. To activate the X2 Transponder you will need a mylaps.com account (see section 4.1 to create a free account).
2. Complete your signup details and click “Create account”. 3. An email will be sent to the email address provided in the sign up form and the following message appears. X2 Transponder Manual (Revision 2.
4. Open the email and click on the blue button “Confirm your new MYLAPS account” (if the email does not show up in your inbox, check your junk or spam filter as it may be there). 5. After clicking the link (blue button), the account activation page will open. Create and confirm you password. 6. After clicking the Activate account button (blue button), a confirmation explains your account is active. X2 Transponder Manual (Revision 2.
7. Click “Login” to go to the log in screen. 8. Proceed to section 4.2 (Register X2 Transponder) and section 4.3 (Activate the X2 Transponder). 4.2. Register X2 Transponder Make sure you follow all the registration steps. Your X2 Transponder is only success fully registered if you complete all steps. Make sure you do not disconnect the X2 RaceKey from your computer during registration and activation. 1. Visit www.mylaps.
3. Click “Register” and check that the following confirmation screen appears. 4. Here, you can click the “Download MYLAPS Connect” button to install the application onto your computer (needed to activate your X2 Transponder) – see section 4.3.1 for downloading MYLAPS Connect. X2 Transponder Manual (Revision 2.
4.3. Activate the X2 Transponder using MYLAPS Connect 1. Ensure you have a current MYLAPS Connect application loaded on your computer – see section 4.3.1. Also make sure your computer is connected to the internet. 2. Startup MYLAPS Connect on your computer. 3. Login to MYLAPS Connect with your MYLAPS Email and Password. 4. Wait until the “No X2 RaceKey detected. Searching for X2 RaceKey” message appears: 5. Attach your X2 RaceKey to your computer with the USB cable. X2 Transponder Manual (Revision 2.
6. The activation process starts automatically and the following message appears: Notice that the information on the right of the screen explains the current status of your transponder subscription (green tick = subscription is valid for more than 30 days; orange icon = subscription is valid for 1 to 30 days; red icon = subscription is expired and must be renewed). X2 Transponder Manual (Revision 2.
7. Wait until the activation is complete and the following message appears: 8. Connect the X2 RaceKey to the X2 Transponder (either directly to the back of the rechargeable transponder; or via the mount to the direct power transponder). The X2 Transponder is immediately activated (the lamp on the transponder blinks green). For Rechargeable: For Direct Power: X2 Transponder Manual (Revision 2.
4.3.1. Install MYLAPS Connect When you are activating your X2 Transponder for the first time, or when you use a new computer for activation, you will need to install the MYLAPS Connect application on the computer: 1. Visit www.mylaps.com and access the download program directory or from your registration screen. 2. Double click the MYLAPS Connect Setup Wizard file and download the application onto your computer by following the setup wizard screen prompts. 3. Choose your language and click OK. 4.
6. Choose a suitable location for the application and click "Next". 7. Select a suitable location for the program shortcut icon and click "Next". 8. Check all settings are correct and click "Install". X2 Transponder Manual (Revision 2.
9. Click "Finish" to complete the installation. 4.4. Reactivate the X2 RaceKey and X2 Transponder To ensure the functionality of your X2 Transponder, reactivate it periodically with the X2 RaceKey (at least once every 5 days). When the transponder is not reactivated, it will stop sending out its transponder number, and the subscription indicator light will flash red 5 times per second. During a race, keep the direct power X2 RaceKey in its mount to ensure it stays activated.
The mounting position of the X2 Transponder must be identical on all vehicles competing in a race. The X2 Transponder components can be mounted to a car, motorcycle, MX or kart For the direct power model, see section 5.1 For the rechargeable model, see section 5.2 5.1. Mounting direct power model 1. Insert the vibration rubbers and attachment pins correctly in the X2 Transponder mounting holes. 2. Mount the X2 Transponder in the car front wheel arch, or bike front forks, or kart lower chassis.
3. Connect the X2 RaceKey mount as follows: Connect power cable connector to the X2 RaceKey mount and connect the open end wires to a 12 VDC supply in your vehicle (check the cable and vehicle wiring specifications for correct connection). The brown cable is 12V and the Blue cable is Gnd. The black and white cable can be ignored. Connect the connector cable to the X2 Transponder and feed it to the connector on the RaceKey mount.
5.2. Mounting rechargeable model 1. Before mounting the X2 Transponder, charge it as follows: Slide the X2 RaceKey onto the X2 Transponder Connect the USB cable from a USB/wall adapter (e.g. laptop) to the X2 RaceKey. The charge indicator light blinks red during charging. Wait till the light turns solid green (the transponder is fully charged). Remove the USB cable and disconnect the X2 RaceKey from the X2 Transponder. The indicator lights (see section Error! Reference source not found.
6. Maintenance Maintenance can be described as, but not limited to: Checking and testing components; Cleaning the unit and individual components - accumulated dirt can hamper unit operations; Charging the unit; Troubleshooting any malfunctions that may occur on the unit during operation. 6.1. Periodic maintenance schedules Type of maintenance Clean Charging Replace parts and accessories 6.2.
6.3. Charging (Rechargeable X2 Transponder only) Make sure the X2 Transponder is dry before charging. If the transponder is inactive for long periods, charge it once every three months. 1. Mount the X2 RaceKey on the X2 Transponder. 2. Connect the USB cable from a USB/wall adapter source (e.g. laptop) to the X2 RaceKey. 3. The charge indicator light blinks red during charging. Wait till the light turns solid green (the transponder is fully charged). 4.
7. Environment and disposal Do not dispose of electrical equipment in the household waste! The symbol on the material, accessories or packaging indicates that this product may not be discarded as household waste. Dispose of the equipment through a recycling centre that handles electronics and electrical appliances within the EU and in other European countries which use separate collection systems for used electronics and electrical appliances.
8. Troubleshooting This product contains delicate electronic components. This means that if it is placed near an object that transmits radio signals, it could cause interference. This could be, for example, mobile telephones, walkie talkies, CB radios, remote controls and microwaves. If interference occurs, move such objects away from the appliance. Electrostatic discharges can lead to malfunctions. In the event of such malfunctions briefly remove and reinsert the rechargeable batteries. 9.
9.2. Car/Bike Timing resolution 2 ms Max. Speed 260 km/h (162.5 mph) Transponder position Max. Height 120 cm (4 ft.) for bikes, 60 cm (2 ft.) for cars. Clear view to the asphalt 9.3. Kart Timing resolution Max. Speed Transponder position 9.4. 3ms 120 km/h (75 mph) Max. Height 30 cm (2 ft.) MX Timing resolution Max. Speed Transponder position 9.5. 6ms 120 km/h (75 mph) Max. Height 120 cm (4 ft.) X2 RaceKey Dimensions 50x30x15 mm / 1.96x1.18x0.59 in Weight 30 gr / 0.
9.6. USB cable Description 0.50M USB micro - USB A, black Color of housing Black Type of plug 1x USB A male 1x USB micro Length 0.5 m (19.7 inch) Outer diameter 3 mm ((0.12 inch) 9.7. Cable (X2 RaceKey mount to 12 VDC power supply) Type Cable; Open end without connector Material PUR halogen free Color of housing Black Number of contacts 4 Thread M8 Type of plug 1x female (M8 female connector with snap-in joint, straight, 4-poles) Length 1,5 m (59.1 inch) Outer diameter 4.
9.8. Cable (X2 RaceKey mount to transponder) Type Cable with double-ended connectors Material PUR halogen free Color of housing Black Number of contacts 4 Thread M8 Type of plug 1x female (M8 female connector with snap-in joint, straight, 4-poles) 1x male (M8 male connector with self-locking threaded joint, straight, 4-poles) Length 2 m (78.7 inch) Outer diameter 4.5 mm (0.
10. MYLAPS Support MYLAPS EMEA Office Haarlem Tel: +31 23 7600 100 Email: tech.support@mylaps.com MYLAPS Americas Office Atlanta Tel: +1 678 216 4000 Email: info.americas@mylaps.com MYLAPS Japan Office Tokyo Tel: +81 3 5275 4600 Email: info.japan@mylaps.com MYLAPS Asia Pacific Office Sydney Tel: +61 2 95462606 Email: info.asia.pacific@mylaps.com MYLAPS Asia Office Kuala Lumpur Tel: +60 356131235 Email: info.asia@mylaps.com X2 Transponder Manual (Revision 2.