User Guide
MINI HD PROJECTOR
INSTRUCTION MANUAL
MODEL NO. : PJ-32
Please Read Before Operating This Equipment
Offcial E-mail: Support@imydash.com
Controls of Remote
Remove the battery compartment cover on the back of your
remote by carefully sliding to open. The battery cover can then
be lifted away. Fit the correct batteries (not included), referring
to the polarity markings. Finally, replace the cover.
NOTES:
Batteries shall not be exposed to excessive
heat such as placing under the sunlight or
near a fire.
Please make sure the batteries are installed
with their correct polarities.
Do not mix old and new batteries.
Use only the same type of batteries.
Do not dispose of the batteries in fire,
battery may explode or leak.
Do not recharge a non-rechargeable
battery.
9
Controls of Projector
11 SNEL 1 Buttons
2 ANGEL ADJ. Knob 12
Buttons
3 AC IN Socket 13
Button
4 FOCUS ADJ. Knob 14 Audio out Jack
5 TRAPEZOIDAL ADJ. Knob 15 AV IN Jack
6 POWER Indicator 16 TF Card Slot
7
POWER
Button
17 HDMI 1 & 2 Ports
8
RETURN
Button
18 USB Port
9
SOURCE
Button
19 VGA IN Port
10
MENU
Button
20 IR Sensor
1
1
2
Controls of Projector
11 SNEL 1 Buttons
2 ANGEL ADJ. Knob 12
Buttons
3 AC IN Socket 13
Button
4 FOCUS ADJ. Knob 14 Audio out Jack
5 Keystone adujust 15 AV IN Jack
6 POWER Indicator 16 TF Card Slot
7
POWER
Button
17 HDMI 1 & 2 Ports
8
RETURN
Button
18 USB Port
9
SOURCE
Button
19 VGA IN Port
10
MENU
Button
Install Power Adapter
Follow below picture to connect power cable
Connect small end of cable FIRST. Plug the AC plug to power outlet.
WARNING:
Before connecting to the power supply, ensure that the supply
corresponds to the information on the rating label at the back of the
apparatus.
- Press the button to switch on unit, press again to turn off.
/ SOURCE - Press the button to select input source.
/ MENU - Press the button to enter projector menu.
- Press the buttons to navigate and select screen item of menu.
/ EXIT - Press the button to return to previous status or exit the menu.
- Press the buttons to fast search forward and rewind on USB / TF.
- Press the buttons to search next or previous file on USB / TF.
VOL+ / VOL - Press the buttons to select the sound level.
- Press the button to play/pause the playback of file on USB / TF card.
FLIP – Press the button to rotate / mirror projector screen
ZOOM - Press the button to select image scale.
- Press to mute the audio. Press again to resume.
First, ensure the projector and the mobile is connected to the same wireless
network Follow below steps to set up.
Airplay Mirroring Settings (IOS mobile)
1. Press the / SOURCE button to enter and use buttons to select
the Air Play mode.
2. Click the Wi-Fi menu to search and select “RKcast-19A1EF” on the mobile
device and enter Pin “12345678” to connect.
3. After connect, click the browser and input IP “192.168.49.1” address on the
mobile.
4. Click to select Wi-Fi AP, choose the available local Wi-Fi router and input
password to connect.
5. After connect, the router’s name will be on the projector screen.
6. Click Airplay Mirror function on the mobile.
7. The mobile device will mirror and browse online contents to projector. You
can enjoy online video/music/pictures, etc. (This feature is only supported by
iOS 7 or above devices).
Note: When the router is successfully connected, the projector will automati-
cally connect to the router next time. The mobile device can connect the
projector or the router to mirror the network content.
Android Mirroring Settings (DLNA mode)
1. Press the / SOURCE button to enter and use buttons to select
the Air Play mode.
2. Click the Wi-Fi menu to search and select “RKcast-19A1EF” on the mobile
device and enter Pin “12345678” to connect.
3. After connect, click the browser and input “192.168.49.1” IP address on the
mobile.
4. Click to select Wi-Fi AP, choose the available local Wi-Fi router and input
password to connect.
5. After connect, the router’s name will be on the projector screen.
6. Click Screen Sharing or Wireless Display (different mobile models with
different names) on the mobile.
7. The mobile device will mirror and browse online contents to projector. You
can enjoy online video/music/pictures, etc. (This feature is only supported by
Android system 4.2 or above devices).
Note: When the router is successfully connected, the projector will automati-
cally connect to the router next time. The mobile device can connect the
projector or the router to mirror the network content.
Specifications
Light Source Type
LED
HDMI Input Supported
Video Resolution.
1080p , 1080i , 720p, 576i , 480p, and 480i
Power Consumption
67W
Included Adapter Input AC 100-240V, 50/60Hz
Input Port
AV/ VGA / HDMI
USB Port
Support USB device up to 32GB
Su
pport format Mpeg1, Mpeg2, Mpeg4,
mp3, Jpeg
TF Card
Support SD card up to 32GB
Support format Mpeg1, Mpeg2, Mpeg4,
mp3 , Jpeg
Net Weight 1.4 KG
Product Dimensions 230 x 200 x 94 mm
Specifications are typical, individual units might vary. They are subject
to continuous improvement without notice and without incurring any
obligation.
Q: How do I lower the volume?
A: To lower or raise the volume, Press the volume buttons on the remote control
or these buttons on the control panel.
Q: Do you have to have wifi for this to work? or can you also use it without
wifi?
A: Yes, it is Wifi Mirroring projector. You can also use a cable to connect it.
Q: What mode should I choose when inserting with SD card?
A: When inserting SD,TF card /USB,please use the remote to click”SOURCE”
button to choose DMP mode,and HDMI mode for HDMI cable connection, AV
mode for AV cable connection,VAG for VAG cable connection. When using
IOS/Android wireless mirroring setting,please choose “Air Playing Mode”.
Q: Can this projector be positioned vertically to project onto the ceiling?
A: Yes, you can do that with a tripod.
Q: How is the sound quality? Are their speakers built in?
A: Great, all you have to do is press the left/right arrows on the remote control. If
you want, you can choose to connect speakers, but the sound quality is really
good.
Q: Is this micro sd or standard sd port?
A: Standard SD
Q: Can I use the projector for presentation?
A: It depends. If you want to open file from your flash disk plugged in the
projector, it won’t work. But you can open file from laptop by connecting with the
prohector
Q: The projection is not bright enough?
A: We recommended using the projector in a relatively dark enviroment to bring
out the best image brightness.
Q: Does it support Dolby sound?
A: Due to copyrights restrictions,Dolby sound effects are not supported. You can
get better voice when connecting a 3.5mm audio jack.
Q: What is the warranty? How can I connect the seller?
A: Mydash mini projector has one year warranty. You can contact the manufac-
ture directly. They will activate the warranty for you: support@imydash.com
Troubleshooting