Medium & Large Tilt Flat Panel Mount V6 Flat Panel Tilt Mount INSTRUCTION MANUAL MANUAL DE INSTRUCCIONES MANUEL D’ INSTRUCTIONS R ! CAUTION: THE MAXIMUM LOADING WEIGHT IS 120 LBS FOR MEDIUM MOUNT AND 175LBS FOR LARGE MOUNT. USE WITH PRODUCTS HEAVIER THAN THE MAXIMUM WEIGHT INDICATED MAY RESULT IN INSTABILITY AND POSSIBLE PERSONAL INJURY.
QUESTIONS? V1 NEED HELP? PLEASE CALL ¿NECESITA AYUDA? LLÁMENOS. BESOIN D’AIDE? VEUILLEZ APPELER 1-602-674-1000 DISCLAIMER – WARNING INFORMATION Disclaimer –. MW PRODUCTS has extended every effort to ensure to accuracy and completeness of this manual. However, MW PRODUCTS does not claim that the information covers all installation and or operational variables. The information contained in this document is subject to change without notice or obligation of any kind.
HARDWARE PRODUCT NUMBERS 8 1 2 3 4 5 6 M4 x 12 X4 M6 x 15 X4 M8 x 15 X4 M4 x 30 X4 M6 x 30 X4 M8 x 30 X4 7 M8 x 50 X4 13 9 10 11 12 5mm SPACER X4 10mm SPACER X4 STEEL WASHER X8 LAG BOLT 8mm x 65mm X4 LAG BOLT STEEL WASHER X4 SQUARE WASHER X4 14 WALL ANCHOR X4 PRODUCT COMPONENT PARTS Flat Panel Mounting Pattern (W X H) Minimum: 100mm x 100mm (Medium and Large) Maximum: 400mm x 400mm (Medium) Maximum: 700mm x 400mm (Large) 15 B B R A C C Product Components Qty Part # 15 De
STEP 1A - FLAT BACK FLAT PANEL (UNIVERSAL VERTICAL RAILS) Connect Universal Vertical Rails to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur 1 or 2 or 3 8 X4 STEP 1B - CURVED BACK FLAT PANEL (UNIVERSAL VERTICAL RAILS) Connect Universal Vertical Rails to flat panel Conecte el adaptador al monitor Connectez l'adaptateur au moniteur Spacers can also be used to provide clearance for cables and connectors.
STEP 1- USE M8 STEEL WASHER IF THE PHILLIPS SCREWS FROM THE MONITOR KIT ARE TOO LONG Diagrams show three options for using additional washers if hardware screws are too long to properly tighten into back of flat panel television.
STEP 2- CENTER WOOD STUD INSTALLATION INSTALLATION SKIP TO STEP 3) STEP 2UNIVERSAL MONITOR (CONCRETE PLATE Find stud and mark edge and center locations Ubique el panel y marque las ubicaciones de los bordes y el centro. Repérez l'emplacement d'une poutre, puis marquez l'emplacement des bords et du centre de cette poutre.
STEP 2C- MOUNT WALL PLATE TO WALL Mount wall plate 16” STUD (Medium Tilt Mount) 16” or 24” STUD (Large Tilt Mount) Coloque la placa de pared Montez la plaque murale 13 12 13 12 X4 P7
STEP 3 – SOLID CONCRETE INSTALLATION Use wall plate to mark mounting locations/ drill pilot holes Use la placa de pared para marcar el lugar donde se realizará la instalación Utilisez la plaque murale pour marquer l'emplacement de montage Level Solid Concrete Drill Bit Drill Pilot Hole DRILL BIT NOT INCLUDED STEP 3A & 3B- POSITION WALL PLATE, MARK, & DRILL PILOT HOLES Position wall plate to desired location, level, and mark pilot locations with pencil.
STEP 3C- SOLID CONCRETE INSTALLATION.
STEP 4A- ATTACH PANELTO WALL PLATE & ADJUST TILT ANGLE Hang vertical rails with monitor attached Cuelgue con el monitor adherido. Accrochez avec le moniteur installé. Flat Panel Vertical Rails Pull spring lock cord down and gently push bottom of panel to wall and release spring lock. Panel is now locked on to wall plate.
STEP 4B- ADDITIONAL SECURITY FEAUTURE (OPTIONAL) Option Opcione Option Flat Panel Vertical Rails Wall Plate R Vertical Rails have 7mm hole located at the bottom for placement of pad lock for additional theft security (pad lock not included) STEP 4D - ADJUST STRAP LENGTH (OPTIONAL) Squeeze and hold control to adjust cord length Attach pendant to wall plate with magnet.
Congratulations! Installation complete WARRANTY INFORMATION This warranty applies to US Residents who purchase from an authorized MW PRODUCTS Dealer. MW PRODUCTS products are covered against defects in materials and workmanship for 5 years. MW PRODUCTS will repair or replace the defective component or product, at its sole discretion. Failure to follow product care instructions from MW PRODUCTS will result in void of warranty.