Synchronizable Digital Audio Sync Master Clock Generator G MUTEC part no.
SAFETY INSTRUCTIONS General instructions To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture, direct sunlight or excessive heat from sources such as radiators or spotlights. No user serviceable parts are inside. Repair and maintenance must be carried out by qualified personnel authorized by MUTEC GmbH! The unit has been designed for operation in a standard domestic environment.
CONTENT introduction General Description . . . . . . . . . . . . . . . . . . . . . . . 7 MC-3+ Features. . . . . . . . . . . . . . . . . . . . . . . . . .7 MC-3+ Applications. . . . . . . . . . . . . . . . . . . . . . . .8 Peripheral MUTEC Products. . . . . . . . . . . . . . . . . . . 8 CONTROL elementS AND TERMINALS MC-3+ Front Panel . . . . . . . . . . . . . . . . . . . . . . . .
\B E D I E N E L E M E N T E >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> INTRODUCTION Thank you very much for purchasing the MC-3+ Smart Clock, Synchronizable Digital Audio Master Clock Generator, from MUTEC ! General Description The new MUTEC MC-3+ Smart Clock is especially designed to improve the acoustical quality of digital audio devices in two ways: At first by clocking external devices with ultra-low jitter Word Clock signals and secondly by aggressively re-clocking incomin
INTRODUCTION \\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Applications Audiophile sound improvement of digital audio devices Elimination of »clicks and pops« in audio recordings Enhancing and stabilization of existing clock chains Stellate, ultra-low-jitter clock signal supply Addition of redundancy to clock chains in use Increase of clock signal reliability during live events Multiple clock rate synchronization Peripheral MUTEC Products Signal Distribution Amplifiers
\B E D I E N E L E M E N T E >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CONTROL elements AND TERMINALS MC-3+ SMART CLOCK Front Panel 1 2 3 4 5 7 6 8 1 »POWER« This red LED lights up when the unit is switched on with the rear panel POWER switch. 2 »MENU« Use this key to access the different functional menus. Refer to the OPERATIONS chapter for more information. 3 »SELECT« Use this key to select a function within a specific functional menu.
CONTROL ELEMENTS \\\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> For a full list of all Word Clock, AES3 and S/P-DIF clock rates that can be generated, please refer to the »Generatable Word Clock Frequencies« and »Generatable AES3 and S/P-DIF Frequencies« sections in the APPENDIX chapter.
\B E D I E N E L E M E N T E >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> INSTALLATION Content of the Box The unit was packed carefully. Nevertheless we recommend to check the content directly after opening the package: 1 x MC-3+ Smart Clock 1 x Power cable 1 x Manual The condition of the packaging material and the device should be checked carefully additionally. If there are any damages please refer to SAFETY INSTRUCTIONS and WARRANTY REGULATIONS.
I N S TALLAT I O N \\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> bridge, you can use an additional BNC-T piece to terminate the input. Plug the T piece with its center connector into the input of the receiving device. Then, connect the cable coming from the Word Clock output to one of the lateral connectors, and the other connector of the BNC-T piece to a 75 Ω resistor forming the BNC termination.
\B E D I E N E L E M E N T E >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> GENERAL OPERATION Selecting Function Menus and setting Functions Operating the MC-3+ SMART CLOCK is very easy! The device is fully operated using the two keys at the front panel. 1 Pressing the »MENU« key toggles between different basic function menus. 2 Pressing the »SELECT« key activates individual functions within one function menu.
O P E RAT I O N \\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> OPERATING THE MC-3+ Smart Clock Main Function Menus ! Shut-Down of Outputs All digital audio outputs are shutdown during function selection! After a function is finally selected and the corresponding LED lights constantly again, the digital audio outputs are activated for signal transfer. ! User Settings Remain All user-specific function settings are available furthermore when power is restored.
O P E RAT I O N \\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Selecting Modes 1 WCLK 32.0 EXTERNAL 10.0M 44.1 RE-CLOCK S/P-DIF op 48.0 x4 S/P-DIF co 88.2 x 256 MODE 192.0 AES3/11 REFERENCE 96.0 176.4 2 3 4 5 x1 INTERNAL x2 INTERNAL + 10.0M CLOCK MULTIPLIERS This setting example shows the MC-3+ locked to its internal ultra-low-jitter clock base generating output clocks of 44.1kHz at any available output. This is the factory default setting.
ANHANG \\\\\\\\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Selecting References 1 WCLK 32.0 EXTERNAL 10.0M 44.1 RE-CLOCK S/P-DIF op 48.0 x4 S/P-DIF co 88.2 x 256 MODE ! Audio to Blank Frame Conversion Running the MC-3+ in the »EXTERNAL« mode and applying a digital audio signal of the AES3 or S/P-DIF format as reference causes a conversion of the audio signal into a blank frame signal available at the digital audio outputs.
ANHANG \\\\\\\\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Further Setting Examples 1 WCLK 32.0 EXTERNAL 10.0M 44.1 RE-CLOCK S/P-DIF op 48.0 x4 S/P-DIF co 88.2 x 256 MODE 192.0 AES3/11 REFERENCE 96.0 176.4 2 3 4 5 x1 INTERNAL x2 INTERNAL + 10.0M CLOCK MULTIPLIERS A 10.0MHz clock signal is applied as reference and the basis clock of all outputs is set to 48.0kHz.
ANHANG \\\\\\\\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Status Information »STATUS« Area This area displays different system conditions of your MC-3+. There is no access for changing settings. »LOCK« This blue LED lights when the internal PLL circuit has detected the incoming clock reference signal as valid. If the reference signal is unstable or lost, the »LOCK« LED does not light.
\B E D I E N E L E M E N T E >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> APPENDIX Pin Assignment of the Connectors Mains 3 2 1 1 2 3 Live, phase (brown; USA: black) Protective earth (green/yellow; USA: green) Neutral (blue; USA: white) AES/EBU, XLR, Input 2 AES/EBU, XLR, Output 1 1 3 1 2 3 2 3 Audio ground a conductor (hot / +) b conductor (cold / -) BNC In-/Output for Word Clock, Super Clock, 10.
AP P E N D I X \\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Switching-off the Termination of the Word Clock Input CAUTION! Disconnect the unit from the mains before opening! Remount the aluminium cover thoroughly before you attempt to operate the unit! Word Clock Input S/P-DIF Inputs When the MC-3+ Smart Clock is shipped, the BNC-based Word Clock input connector is terminated internally with 75 Ω.
AP P E N D I X \\\\\\\\\\\\ >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> AES3 AUDIO OUTPUT Interface 1 x XLR male, transformer balanced, 3.5Vpp @ 110Ω, output impedance 110Ω, buffered Format, Resolution AES3 – 1992/2003, AES11 – 1997/2003, 24 bits Transmitted Clock Rates 25.0kHz to 200.0kHz S/P-DIF optical output (op) Interface 1 x Toshiba ToslinkTM, EIAJ RC-5720 Format, Resolution IEC 60958, 24 bits Transmitted Clock Rates 25.0kHz to 200.
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> ALL SOFTWARE AND HARDWARE PRODUCT NAMES ARE REGISTERED TRADEMARKS OF THEIR RESPECTIVE OWNERS. WE RESERVE THE RIGHT TO CHANGE TECHNICAL DETAILS WITHOUT PRIOR NOTICE. ©MUTEC GmbH 2002 •7045-014 WWW.MUTEC-NET.