User's Manual

ManualsBrandsMusical Fidelity Manualsaudio & home theatreX-80

Issue 4 May 2004

X-80 Integrated Amplifier Page 1 of 8X-80 Integrated Amplifier Page 8 of 8

X-80 SPECIFICATIONS

INSTRUCTIONS FOR USE

Thank you for purchasing the Musical Fidelity

X-80 Integrated amplifier.

Used properly and carefully, it should give you many years of

outstanding musical reproduction.

Aesthetically, the X-80 Integrated amplifier is a perfect match for the

X-RAY CD player and X-PLORA FM tuner.

Together, they form one of the finest hi-fi systems available.

Dust regularly with a soft cloth or soft brush, but be careful when

using cleaning or polishing agents - they may harm the surface finish.

If you have any questions about your audio system,

please consult your dealer who is there to help and advise.

X-80

DUAL MONO INTEGRATED AMPLIFIER

Output :Voltage RMS : 21 Volts 20Hz to 20kHz, one channel loaded

Peak : 59 Volts

Power : 55 Watts one channel into 8 Ohms (17.4dBW)

85 Watts one channel into 4 Ohms

Peak-to-peak output current : 28 Amps

Damping factor : 77

Output devices per channel : 2

Pre-output impedance : 50 Ohms

Line inputs :

Total harmonic distortion + noise : < 0.02% 20Hz to 20kHz

Signal / noise ratio : > 93dB ‘A’-weighted

Input sensitivity for 55Watts, 8 Ohms :175mV

Input impedance : 220k Ohms

Overload margin : 29dB

Channel separation : > 55dB typical

Frequency response : 20Hz to 20kHz, + 0, - 0.4dB

Input facilities : 4 pairs line level RCA connectors

Output facilities : 2 amplifier channels via 1 pair per channel binding posts.

1 pair RCA audio outputs controlled by the volume,

1 pair RCA tape record fixed line level output.

Power requirement : 100 / 115 / 230Volts AC 50 / 60Hz (factory pre-set),

190 Watts maximum into 8 Ohms, 15 Watts idle.

Dimensions : 218mm, 8.6 inches wide

98mm, 3.8 inches high (including feet)

339mm, 13.4 inches deep

(including knob and rear terminals)

Weight : 6.5 kg, 14.3 lbs unit only, unboxed

8 kg, 17.7 lbs in shipping carton

Standard accessories : IEC type mains lead (10-Amp), remote control,

2 batteries size LR03 or AAA, manganese alkaline type

Musical Fidelity reserves the right to make improvements which may result in specification

or feature changes without notice.

Summary of content (4 pages)

PAGE 1
X-80 SPECIFICATIONS Output : Voltage RMS : Peak : Power : 21 Volts 20Hz to 20kHz, one channel loaded 59 Volts 55 Watts one channel into 8 Ohms (17.
PAGE 2
SAFETY INFORMATION OPERATION IMPORTANT! (U.K. only) BEFORE SWITCHING ON TAPE RECORDING This unit is supplied in the U.K. with a mains lead fitted with a moulded 13 amp plug. If, for any reason, you need to cut off this plug, please remove the fuse holder and dispose of the plug safely, out of reach of children. It must not be plugged into a mains outlet. Plug the accessory IEC mains lead into the rear panel socket, then the other end into a wall outlet.
PAGE 3
CONNECTIONS All input, output and power connections should be made with the mains power switched OFF. INPUT CONNECTIONS The X-80 has four pairs of “line level” inputs controlled by the internal volume setting. They all have the same input sensitivity, and are therefore suitable for use with any source component having an output of at least 300mV. The four left and right socket pairs on the rear panel are marked INPUT 1, 2, 3 and 4, corresponding with the blue function indicator LEDs on the front panel.
PAGE 4
CONNECTIONS & FACILITIES REMOTE CONTROL REMOTE CONTROL Buttons on the remote control with blue-grey surround enable main functions of the amplifier to be operated from a convenient distance. Remaining buttons on this universal handset are for use with other Musical Fidelity products, and have no effect on the X-80 Integrated amplifier.