Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
4 5 6 Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.
WHICH MAY BE SUFFERED BY ANY PERSON WHO RELIES EITHER WHOLLY OR IN PART UPON ANY DESCRIPTION, PHOTOGRAPH OR STATEMENT CONTAINED HEREIN. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. MUSIC GROUP PRODUCTS ARE SOLD THROUGH AUTHORIZED FULLFILLERS AND RESELLERS ONLY. FULLFILLERS AND RESELLERS ARE NOT AGENTS OF MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIEDUNDERTAKING OR REPRESENTATION. THIS MANUALIS COPYRIGHTED.
EUROPORT Set-up Step 1: Hook-Up Debate Centre de débat Podiumsdiskussion PPA2000BT/PPA500BT
Step 2: Set-up 1,Release the top latch beneath the carrying handle 2,Release the side latches by pressing and then lifting them. 3,Remove the speakers and place them in appropriate locations.
4,Stand the mixer upright.
Step 3: Controls. FX knob determines how much of each EQ KNOBS adjust the high and low channel’s signal goes to the DIGITAL frequencies for each channel. EFFECTS PROCESSOR.
PAN knob positions each channel in the stereo field. LEVEL knob adjusts the CLIP LED lights when the volume of the individual input signals overloads the channel in the overall mix. channel. MULTI-FX PROCESSOR unit adds a selected sound effect to any channels which have their PROGRAM[PUSH] EFFECTS knob controls the effects Effects include reverb, chorus, controls the amount of settings. Rotate this knob delay, and pitch shifter.
GRAPHIC adjusts EQ EQ specific activates button FBQ the GRAPHIC EQ. frequencies in the sound spectrum. button MAIN adjusts the overall volume of detection system. the main mix. The MODE The EQ IN button switch selects stereo or mono must operation. also be feature to work. the STEREO CHANNELS accept and right connects, CD players, channel input signal by 20dB.
AUX IN inputs route stereo signals directly into the main mix through either a sginle1/8’’TRS stereo plug or left and 1/4’’plugs DIGITAL WEIRELESS USB MIC INPUT PHANTOM button input optional jacks sends wireless dynamic(hand phantom power to microphone receiver. The LEDs held)or power indicate condenser microphones.
STEREO AUX IN RECORDING OUT jacks stereo send the main mix signal out to signals directly into the an external recording device or main mix through either another mixer. inputs route a signal’s 1/8’’ TRS stereo plug or left and right 1/4’’plugs. SPEAKER OUTPUTS connect to the speakers using speaker cables with 1/4;;plugs.DO NOT USE INTRUMENT CABLES AND ONLY USE THE INCLUDED SPEAKERS.
POWER switch turns the power to the unit on and off . POWER SOURCE accepts the included IEC power cable into this jack.
1,Connect the included speaker cables to the speakers and to the rear SPEAKER OUTPUTS on the mixer. 2, Make all the appropriate audio connections to the mixer. Power down all external devices. 3, Set all the channel controls as shown (TREBLE, BASS, and BAL centered; EFFECTS and LEVEL down/off). 4,Center the GRAPHIC EQ faders. 5, Set the MAIN LEVEL CONTROL knobs all the way down.
6,Power up all external devices. 7, Power up the PPA2000BT/PPA500BT by pressing the POWER button. 8,If you are using BEHRINGER wireless microphones, plug the wireless dongle into the DIGITAL WIRELESS USB input, The DIGITAL WIRELESS LEDs will light up when the wireless microphones become active. 9, Slowly turn the MAIN LEVEL CONTROL knobs up 1/3 of the way.
11, If a channel’s CLIP LED lights, press the PAD button. If the PAD button is already engaged, turn the LEVEL knob down. Always use the pad button with line level inputs. 12, Adjust the left-right position of a channel in the stereo field by turning the channel’s PAN knob.
13, Make final volume adjustments using the MAIN LEVEL CONTROL knobs.
Step 5: Adding Effects 1,Set the FX [LEVEL] knob on the DIGITAL EFFECTS PROCESSOR to approximately a 75% setting. 2, Scroll through the available effects by turning the PROGRAM [PUSH] knob. The number in the display will flash. 3, Press the PROGRAM [PUSH] knob to select the effect. The number will stop flashing. 4, While speaking, singing, or playing, turn the channel FX knob up to the desired level on each channel to which you wish to add effects.
5, Adjust the FX [LEVEL] knob on the DIGITAL EFFECTS PROCESSOR up or down from the initial 75% setting to achieve your desired overall effects level in the main mix. Step 6: Feedback Detection “Feedback” is the undesirable high-pitched sound created by sound waves looping between the speakers and the microphones. 1, If feedback occurs, press the EQ and FBQ ON buttons.
feeding back. 3, Lower the lit EQ slider until feedback stops.
Specifications INPUTS 1-4 Type 4xXLR,electronically balanced 4x1/4’’TRS jack, electronically balanced Impedance Approx2.2 kohm, balanced Approx 1.1 kohm, unbalanced Input -21 dBu @PAD/OFF Max.gain +30dB to +10dB Phantom power supply +48V Signal-to-noise ratio -90dB, A-weighted Channel separation 70dB INPUTS 5-8 Type 4x1/4’’TS jack, unbalanced 4xRCA jack, unbalanced Impedance Approx,20ohm, unbalanced Input sensitivity -15dBu Max.
BASS ±15dB @80Hz TREBLE ±15dB @12kHz EFFECTS Converter 24-bit delta-sigma Sampling frequency 40kHz Display 2-digit, 7-segment EQ Type 7-band LOUDSPEAKER OUTPUTS Type 2x1/4’’ TS jack Load impedance 8ohm OUTPUT POWER RMS(@8ohm) 2x160 Watts RMS(@4ohm) 2x300 Watts PEAK power(@8ohm) 2x500 Watts PEAK power(@4ohm) 2x1000 Watts SYSTEM SPECIFICATIONS Frequency response 50Hz to 20kHz, ±3dB Distortion 0.
BLUETOOTH Frequency Range 2402~2480 MHz Channel Number 79 Version Bluetooth spec V2.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.