User Manual to FCC Murata Manufacturing Co.,Ltd. 1 1 murata.com Copyright © Murata Manufacturing Co., Ltd. All rights reserved. Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
1SS User Manual Product Outline This product has a function as an NB-IOT ・Product Size :10.6 x 13.2 x 1.8(max) [mm] ・RF-IC :MediaTek MT2625 ・Reference Clock :26MHz X’tal Feature ・Product Name :Communication Module ・Model Name :1SS ・Purpose of the equipment :Telecommunication ・Equipment Type :Transceiver ・Frequency Band ・Channel Bandwidth ・Input Voltage to RF parts :B2/B4/B5/B12/B13/B17/B66/B71/B85 :200kHz :AVDD33, AVDD33_VPA Typ.3.3V CONFIDENTIAL Copyright © Murata Manufacturing Co., Ltd.
1SS User Manual FCC ID: VPYLB1SS The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warming as shown in User manual. This device complies with part 15 of the FCC Rules.
Notice List of applicable FCC rules This module complies with below part 22, 24 and 27 of the FCC Rules. Part 22 Subpart H Part 24 Subpart 24E Part 27 Subpart B, C & L CONFIDENTIAL Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
Notice Trace antenna designs and Antennas Antenna ANT-LTE3-2(Monopole Antenna) Antenna maker: Murata Manufacturing Co.,Ltd. Antenna peak gain: 4.2dBi(Rx), 1.8dBi(Tx) Antenna impedance: 50Ω Details: Please refer document of antenna specification. Band Peak Tx gain(dBi) Band Peak Tx gain(dBi) Band Peak Rx gain(dBi) Band Peak Rx gain(dBi) B2 1.8 B13 1.1 B2 2.6 B13 0.1 B4 -0.4 B66 0.5 B4 4.2 B66 4.2 B5 1.5 B71 0.5 B5 1.2 B71 0.6 B12/17 -0.1 B85 0.0 B12/17 0.1 B85 0.
Notice ■Please check the following points when changing antenna. The concrete contents of a check are the following three points. 1)It is the same type as the antenna type of antenna specifications. 2)An antenna gain is lower than a gain given in antenna specifications. 3)The emission level is not getting worse. If they do not correspond, it is necessary to apply Class 2 change application accompanied by test. Fine tuning of return loss etc. can be performed using a matching network.
Notice RF exposure considerations ●When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. ●When installing it in a portable equipment. Please describe the following warning to the manual.
Notice Label and compliance information ●Please describe the following warning on the final product which contains this module. Contains Transmitter Module FCC ID:VPYLB1SS CONFIDENTIAL or Contains FCC ID: VPYLB1SS Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
Notice Additional testing, Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Notice This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.