User's Manual

ManualsBrandsMurata Manufacturing ManualsElectronicsCommunication Module

08 September 2016

LBEE6ZZ1FD Installation Manual

FCC ID of this product is as follows.

FCC ID:VPYLB1FD

For OEM integration only – device cannot be sold to general public.

Therefore we will ask OEM to include the following statements required

by FCC on the product and in the Installation manual Notice.

Contents

1.Supply Voltage

2.Theory of operation

3.Antenna

4.Notice

Confidential

Summary of content (9 pages)

PAGE 1
Confidential LBEE6ZZ1FD Installation Manual FCC ID of this product is as follows. FCC ID:VPYLB1FD For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC on the product and in the Installation manual Notice. Contents 1.Supply Voltage 2.Theory of operation 3.Antenna 4.Notice Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
PAGE 2
Confidential 1.Supply Voltage min. typ. max. unit -40 +25 +85 deg.C VDD 3.2 3.6 4.5 V VIO 1.62 1.8or3.3 3.63 V Specification Temperature Range Specification Voltage Copyright © Murata Manufacturing Co., Ltd. All rights reserved.
PAGE 3
Confidential 2. Theory of Operation Frequency of operation 2.
PAGE 4
Confidential 3.Antenna ■Please perform the antenna design that followed the specifications of the antenna. The concrete contents to check are the following four points. １）Antenna is the "GW.59.3153" made by “Aoglas antenna solutions“. ２）Confirm the feed line the same as the Gerber file. ３）OEM should be designed so that end users can not change the antenna. Ex1) Use the connecter of reversed polarity. Ex2) Cannot access to the antenna connecter, because use the special screw .
PAGE 5
Confidential 4.Antenna ■Notes If you want to change the antenna. The concrete contents to check are the following three points. １）Please select the same type dipole antenna. ２）An antenna gain is lower than a gain given in antenna specifications. ３）Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. ４）The emission level is not getting worse. Antenna Antenna type 2.4GHz Dipole Antenna 5GHz Dipole Antenna Copyright © Murata Manufacturing Co.
PAGE 6
Confidential 5. Notice For OEM integration only – device cannot be sold to general public. Therefore we will ask OEM to include the following statements required by FCC/IC on the product and in the Installation manual Notice. Please describe the following warning on the final product which contains this module. Contains Transmitter Module FCC ID:VPYLB1FD or Contains FCC ID:VPYLB1FD ●Please describe the following warning to the manual. This device complies with part 15 of the FCC Rules.
PAGE 7
Confidential 5. Notice ●When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. RF Exposure requirements are met when installed in mobile equipment.
PAGE 8
Confidential 5. Notice This device is intended only for OEM integrators under the following conditions: 1)The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2)The transmitter module may not be co-located with any other transmitter or antenna. 3)The use of an antenna with gain less than 2.37dBi (2.4GHz) and 2.93dBi (5GHz). As long as 3 conditions above are met, further transmitter test will not be required.
PAGE 9
5. Notice Professional installation instruction 1. Installation personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. 2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. 3.