Specification Number : SP-xxxx P.1/18 ZigBee Module Data Sheet Sample Part Number: CMBA1ZZABE For 802.15.
Specification Number : SP-xxxx P.2/18 Revision History Revision Code 0.1 Date May.14,2013 Description Comments TYPE-ABE_Prelimi Initial Draft nary_20150323 -Modify size description, add tolerance information 0.2 May.07,2015 -Modify Maximum transmitting power from 8dBm to 5dBm -Modify Operating Voltage from 2V~3.6V to 0.3 July.10,2015 2.7V~3.6V -Add information of packing condition and storage condition 0.4 July.22, 2015 0.5 Aug.26, 2015 0.6 Nov.
Specification Number : SP-xxxx P.3/18 TABLE OF CONTENTS 1. Scope ··························································································································4 2. Part Number ··················································································································4 3. Dimensions, Marking and Terminal Configurations ··························································5 4.
Specification Number : SP-xxxx P.4/18 1. Scope This specification is applied to the IEEE802.15.4 ZigBee Module - Interface : UART, SPI, PWM - IC : CC2530 (Texas Instruments) - Reference Clock: 32MHz reference clock is integrated. - RoHS : This module is compliant with the RoHS directive. 2.
Specification Number : SP-xxxx P.5/18 3. Dimensions, Marking and Terminal Configurations Table 1 Dimension (Unit: mm) Mark Dimension Mark Dimension Mark Dimension L 25.0±0.2 W 17.4±0.2 T 3.1 max a1 0.8±0.1 a2 0.8±0.1 b1 1.6±0.15 b2 0.4±0.1 b3 1.0±0.1 b4 6.0±0.1 b5 7.0±0.1 b6 0.25±0.15 b7 3.15±0.1 b8 2.2±0.1 b9 2.6±0.1 b10 2.6±0.1 b11 2.2±0.1 b12 3.15±0.1 c1 1.0±0.1 c2 1.0±0.1 e1 0.6±0.1 e2 1.4±0.1 Note: This module cannot connect to the external antenna.
Specification Number : SP-xxxx P.
Specification Number : SP-xxxx P.7/18 Terminal Configurations < Top View > Table 2 Terminal Configurations Connection to Pin NO. Terminal Name Type IC terminal Description 1 GND Ground - Ground 2 GND Ground - Ground 3 GND Ground - Ground 4 GND Ground - Ground 5 P2_4 I/O P2_4 Port 2_4/32.768kHz XOSC Q1 6 P2_3 I/O P2_3 Port 2_3/32.
Specification Number : SP-xxxx P.
Specification Number : SP-xxxx P.
Specification Number : SP-xxxx P.10/18 4. Maximum absolute ratings Table 3 Maximum ratings Item Storage Temperature VCC Voltage on any Digital Pin Input RF Level Min -40 -0.1 -0.1 Max +85 3.7 VCC+0.1 10 Unit degC V V dBm Remarks Unit degC V Remarks 5. Operating Condition Table 4 Operating specification Item Operating Temperature VCC Min -40 2.7 Typ 25 3.3 Max +85 3.6 6. Electrical Characteristics Table 5 Electrical specification parameters (Condition: T= +25deg.C, VCC=3.
Specification Number : SP-xxxx P.11/18 7. Power Sequences 8.1 Power Up/Down Sequence Power Up Power Down H VCC L Ta Tc H RST_N L Tb Td H GPIO L 8.2 Reset and Power Cycle Sequence H VCC H RST_N Te L Symbol Ta Tb Tc Td Te Description Time between VCC valid and RST_N ramped-up Time between VCC valid and GPIO enabled Time between RST_N invalid and VCC invalid Time between GPIO invalid and VCC invalid Length of RST_N pulse Typ.
Specification Number : SP-xxxx P.12/18 8. Packing Condition There are 50pcs of products per tray. One inner box has nice trays including one tray without products for top. Products quantity of one inner box is 400pcs. One outer box has four inner boxes. Products quantity of one outer box is 1600pcs.
Specification Number : SP-xxxx P.13/18 NOTICE 1 Storage Conditions: Please use this product within 6 months after receipt. The product shall be stored without opening the packing under the ambient temperature from 5 to 35 °C and humidity from 20 to 70 %RH. (Packing materials, in particular, may be deformed at the temperature over 40 °C) The product shall be stored in non-corrosive gas (Cl2, NH3, SO2, NOx, etc.).
Specification Number : SP-xxxx P.14/18 3 Standard PCB Design (Land Pattern and Dimensions) : All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern should be provided between IN and OUT terminals. Please refer to the specifications for the standard land dimensions. The recommended land pattern and dimensions is as Murata's standard.
Specification Number : SP-xxxx P.15/18 5 Soldering Conditions : The recommendation conditions of soldering are as in the following figure. When products are immersed in solvent after mounting, pay special attention to maintain the temperature difference within 100 °C. Soldering must be carried out by the above mentioned conditions to prevent products from damage. Set up the highest temperature of reflow within 260 ℃. Contact Murata before use if concerning other soldering conditions.
Specification Number : SP-xxxx P.16/18 7 Operational Environment Conditions: Products are designed to work for electronic products under normal environmental conditions (ambient temperature, humidity and pressure). Therefore, products have no problems to be used under the similar conditions to the above-mentioned. However, if products are used under the following circumstances, it may damage products and leakage of electricity and abnormal temperature may occur.
Specification Number : SP-xxxx P.17/18 cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.
Specification Number : SP-xxxx P.18/18 IC: 772C-CMABE" This Class B digital apparatus complies with Canadian ICES-003. Cetappareilnumérique de la classe B estconforme à la norme NMB-003 du Canada. This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
