EkoTek Call Fob USER GUIDE For EkoTek Call Fob 9261-8277 (Issue 2.
EkoTek Call Fob CONTENTS Introduction 3 Compliance 4 General User Information 5 EkoTek System Schematic 6 Switching On Your Call Fob 7 Status and Warning Messages 7 Switching the Call Fob Off 8 Requesting Assistance or Raising an Alarm 8 Cancelling an Alarm 8 Dead Man Alert 9 Man Down Alert 9 Changing the Battery 10 2
EkoTek Call Fob Introduction Your EkoTek Call Fob is a two-way alerting device, incorporating emergency calling and assist functions. Function & Control Buttons Operation of all functions is performed using 2 buttons: The RED button is used for Assist calls.
EkoTek Pager Compliance This product complies with the requirements of the EU Radio & Telecommunications Terminal Equipment Directive 99/5/EC. FCC & Industry Canada Statement Of Compliance This device complies with Part 15 of the FCC Rules and Industry Canada Standard RSS 210. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference that may cause undesired operation.
EkoTek Call Fob General User Information Radio Reception Your EkoTek Call Fob has been designed to give optimum performance within the coverage area of the transmitting system. As with any radio system there may be areas of poor coverage, where reception may be sporadic, or non-existent. If necessary, consult your system administrator in order to familiarise yourself with these areas. Hazardous Areas The EkoTek Call Fob should not be taken into areas where explosive gas, or dust products, may be present.
EkoTek Pager EkoTek System Schematic EkoTek Self Organising & Repairing Wireless Mesh Network AC Call Fob Wireless Repeater Power Adaptor Battery Powered Repeater Hub With Web Server Pager Repeater Includes Personal Security Alarm Repeater Repeater to Repeater Distance Typically 10 to 15m Part No. 9261-8277 Issue 2.
EkoTek Call Fob Switching On Your Call Fob To activate the Call Fob press and hold the BLACK button for up to 5 seconds. When activated the Call Fob will emit a single audible pip and the alert/status lamp will flash once indicating that it is switched on. After 10 seconds the alert/status lamp will emit a series of single flashes, this indicates that the Call Fob is in the process of detecting the EkoTek wireless network.
EkoTek Pager When the battery requires changing the Call Fob will emit a single long beep with an accompanying flash of the alert/status lamp. Please refer to: Changing the Call Fob Battery. Out-of-Range Notification If the Call Fob is out-of-range of the EkoTek wireless network, the Call Fob will emit 2-beeps accompanied by 2-flashes of the alert/status lamp. Switching the Call Fob Off To switch the Call Fob off.
EkoTek Call Fob the BLACK button, this is acknowledged by a single flash of the alert/status lamp in conjunction with a single pulse of the vibrate motor. Dead Man Alert Your Call Fob is equipped with a Dead Man alarm feature this facility must be enabled by your EkoTek System Supervisor. The Dead Man Alert initiates an alert to the Call Fob at predetermined time intervals. This alert must be acknowledged within a pre-determined time period by pressing the BLACK button.
EkoTek Pager indicates that the Call Fob must be returned to an upright position in order to terminate the alarm sequence. If the Call Fob cannot be returned to the upright position an alarm will be initiated. To cancel the alarm after it has been initiated press the BLACK button. Changing the Battery When the battery is near the end of its operating life, the Call Fob is programmed to provide a visual and audio warning – A single long beep with an accompanying flash of the alert/status lamp.
EkoTek Call Fob Notes: Part No. 9261-8277 Issue 2.
EkoTek Pager Multitone Electronics plc Multitone House, Shortwood Copse Lane, Basingstoke, Hampshire, England RG23 7DH Part No. 9261-8277 Part No. 9261-8277 Issue 2.
EkoTek Fob – Quick Instructions Button Functions Send Assist call (1 or 2 pushes - configured by Supervisor) Button Function : 1) Clear Assist call (short press) 2) Power ON/OFF (long press) 3) Check if on network (short press) (LED : one flash = off network two flashes = on network) LED – normally OFF When Assist button pressed : Slow flash - alarm being sent 2 fast flashes - alarm delivered 3 fast flashes - alarm accepted Beep & Vibrate Operation of beep and vibrate is set by the Supervisor at the Hub.
EkoTek Fob – Quick Instructions Changing the Battery Align ‘pips’ to remove the battery door AAA Ni-Mh rechargeable or non-rechargeable alkaline batteries may be used in the Call Fob. Compliance This product complies with the requirements of the EU Radio & Telecommunications Terminal Equipment Directive 99/5/EC. FCC & Industry Canada Statement Of Compliance This device complies with Part 15 of the FCC Rules and Industry Canada Standard RSS 210.
EkoTek Fob – Quick Instructions Man-Down Operation (if enabled by Supervisor) To prevent the automatic man-down alarm being sent, keep the Call Fob in an upright position (normally worn in the Call Fob holster on a belt) Dead-Man Operation (if enabled by Supervisor) Press the button to respond to periodic dead-man check (audible beep) and prevent automatic alarm generation Part No. 9261-8311 Issue 2.
EkoTek Fob – Quick Instructions Fonction des boutons Envoi d’un appel d’assistance (1 ou 2 appuis – configuré par le superviseur) Fonction du bouton: 1) Efface l’appel d’assistance (appui court) 2) Marche/Arrêt (appui long) 3) Contrôle la presence d’un réseau (appui court) (DEL : un flash = pas de réseau deux flashes = presence d’un réseau) DEL – Normalement éteint Lorsque le bouton s’assistance est enfoncé: Flash lent – Alarme envoyée 2 flashes rapides – Alarme reçue 3 flashes rapides – Alarme acceptée To
EkoTek Fob – Quick Instructions Changer la batterie Aligner les « repères de centrage » pour retirer le couvercle de la batterie Le porte-clé fonctionne avec des piles alcalines AAA Ni-Mh, rechargeables ou non. Conformité Ce produit est conforme aux exigences énoncées dans la Directive européenne 99/5/EC relative aux équipements terminaux de Radio et de Télécommunications.
EkoTek Fob – Quick Instructions Fonctionnement Homme mort (si autorisé par le superviseur) Pour éviter le déclenchement de l'alarme homme mort automatique, maintenir le téléavertisseur en position verticale (normalement porté dans un étui, accroché à une ceinture) Fonctionnement Homme à terre (si autorisé par le superviseur) Appuyer sur la touché pour effectuer le contrôle périodique homme mort (bip sonore) et éviter le déclenchement automatique de l’alarme Part No. 9261-8311 Issue 2.
EkoTek Fob – Quick Instructions Funciones de las Teclas Enviar llamada de Asistencia (presionar 1 o 2 dos veces – según configuración realizada por el Supervisor) Función de Tecla: 1) Despejar Llamada de Asistencia (pulsación corta) 2) Encender/Apagar (pulsación larga) 3) Verificar si está conectado a la red (pulsación corta) (LED: un destello = desconectado Dos destellos = conrctado) LED – normalmente APAGADO Cuando se presiona la tecla de Asistencia: Destello lento – enviando alarma 2 destellos rápidos –
EkoTek Fob – Quick Instructions Cambio de Batería Alinear los ‘pips’ para retirar la tapa El Call Fob utiliza baterías alcalinas AAA Ni-Mh recargables o no recargables. Cumplimiento Este producto cumple con los requisitos de la Directiva 99/5/EC de la UE sobre Equipos Terminales de Radio y Telecomunicaciones. Declaración de Cumplimiento de la Comisión Federal de Comunicaciones (FCC) y la Industry Canada El equipo cumple con la Parte 15 de las Normas de la FCC y la norma RSS 210 de la Industry Canada.
EkoTek Fob – Quick Instructions Directiva WEEE y Desecho del Producto Al finalizar la vida útil del producto, el mismo no debe ser desechado como residuo doméstico o general. Debe ser entregado al punto de recolección designado para el reciclaje de equipos eléctricos o electrónicos, o bien devuelto al proveedor que le suministró el producto.