Y ENTER WRAL-T-LOCH sev 5. Touch pad Reader Operation 5.1 Operation To turn the Touch pad Reader ON press for 5 seconds. The reader will perform a self test followed by series of beeps. LED blinks Green, Red, Blue. 5.2 Pairing Touch pad Reader This procedure is done via the ENTR® lock. See also: Pairing Remote Control. agp Touch ENTR® lock screen with palm Press [Add] Turmeric buttons Illuminated. or fingers for 3 seconds to active. Type [PIN code] nip 1 Roomer buttons blinking.
f BRA-T-OCH ENTER ov mas. oe Fam {08 indication blinks once, {0K] indication blinks for 15 seconds, 2 short beeps emitted. Mo beeps emitted. ‘Touch pad Reader added. in wl! reader: Green LED illuminated and 2 beeps emitted. Start the process from stage 1. Mute Cig Del Code Mla Add 103 Vv ® » Hang the Touch pad Reader on the base plate. » Tighten fixing screw.
Y ENTER WRAL-T-LOCH sev 5.3 Touch pad Reader Master PIN Code ugh nh Touch screen with palm or fingers, Enter [New master PIN code] Reenter: press [11 wg [4] {4-10 digits) Bp [5] [New master PIN code] RB [1] For sample: 12312348 Gran [OK] Ruminated for 1 second. Red [Freak] Ruminated for 1 second. 2 short beeps emitted. 1 long beep emitted. 54 Menu Mode Entering menu mode: Press « [Master PIN code] « 5.
Y ENTER WRAL-T-LOCH sev 5.6 Open Door nil Touch Reader screen with pam or fingers. Crass [Personal PIN code] wp IE] Red [Error] ruminated for 1 second, 1 long beep emitted. 5.7 Lock Door 2 Touch Reader scream with palm or fingers. Press [1] nip Jt] died [Error] fulminated for 1 second, 1 long beep emitted. 5.8 Delete PIN Code ail ‘ouch Reader screen with palm or fingers.
Y ENTER WRAL-T-LOCH sev 5.10 Volume Control nil “Touch Reader screen with palm or fingers. Press [2] to increase the volume, or [8] to Press fu] gp [aster PIN Code] ty [1:31 decrease the volume. Press [55] ugh ji} Press to confirm volume level. 5.11 Factory Reset The reset action will delete all PIN codes (master and personal) and will cut off the Touch pad Reader from the ENTR® lock. nl Touch Reader screen with palm or fingers.
Y ENTER WRAL-T-LOCH sev 6. Fingerprint Reader 6.1 Mounting the Fingerprint Reader Prior to starting, select the location where the Fingerprint Reader is to be mounted. Avoid direct sun light to the front panel. = Attach the Fingerprint Reader base plate to the wall. * Use 4 screws and screw anchors or double sided glued tape. 6.2 Battery Replacement 1. Using a 2mm Allen key release the lid screw and open the lid. 2. Insert batteries {2xAA) according to the "4" signs.
f BRA-T-OCH ENTER ov mas. oe Fam 6.4 Pairing Fingerprint Reader This procedure is done via the ENTR® lock. See also: Pairing Touch pad Reader. Touch EMTR® lode screen with palm or fingers for 3 seconds to active, 3 nih Press [Add] Turmeric buttons illuminated. Type [PIN code] wip 1] Murine buttons blinking. Mute Cfg Mute Cfg Del Code Code MA Press [1] to add the reader. Illuminated buttons tum off, {ee} indication blinks for 15 seconds waiting for the reader.
Y ENTER WRAL-T-LOCH sev 6.4.1 Add Master User Setting a Master User requires both fingerprint and PIN code. It is possible to have up to two Master Users. Sh ee Te eel tease Ld GT etas re See gene MASTER NAME JOHN MASTER #01 Fel Type in [Master name] agp fom] 6.4.2 Set Finger Blue LED Illuminates. Green LED blinking.
Y ENTER WRAL-T-LOCH er ov mas. oe Fam > > Fixing screw 8 » Hang the reader on the base plate. ® Tighten fixing screw. 6.5 Unlock the Door OPTION 1: OPTION 2: Place finger on fingerprint scanner. Touch the Fingerprint Touch pad. Short beep emitted & white LED Is on. Screen shows user code, Swipe finger over fingerprint scanner Enter your code ugh [ok] Fingerprint authorized: Blue LED blinking and unlock command is sent. Fingerprint not authorized: Red LED is ON. The device goes to standby.
Y ENTER WRAL-T-LOCH —— 6.6 Lock the Door Touch the Fingerprint Touch pad. Press Low Battery Indication Warning signal blinking. Fingerprint Reader low battery indication Red LED illuminate for 1s after wake-up, 2 long beeps emitted. BATTERY LOW 6.