Y ENTER' ML CLOTH E— Table of Content 1. Cylinder Installation 5 1.1 Package Content 5 1.2 Tools Requirements 5 1.3 Prior to Installation 6 14 Cylinder & Unit Installation 6 1.5 Magnet Fitting 8 2. ENTR® Description 9 2.1 ENTR® Description 9 2.2 Indications 9 2.3 ON/OFF Switch 10 2.3.1 Switching the ENTR® ON 10 2.3.2 Switching the ENTR® OFF 10 2.3.2 Low Battery Indication 10 2.4 Initiating the Lock 11 2.5 Default PIN Code 11 3. Operation 12 3.1 Changing PIN Code 12 3.2 Door Configuration 13 3.
Y ENTER' ML CLOTH E— 4. Touch pad Reader 21 4.1 Changing PIN Code 21 4.2 Battery Replacement 21 4.2.1 Low Battery Indication a1 5. Touch pad Reader Operation 22 5.1 Operation 22 5.2 Pairing Touch pad Reader 22 5.3 Touch pad Reader Master PIN Code 24 54 Menu Mode 24 5.5 Adding Personal User Code 24 5.6 Open Door 5 5.7 Lock Door 5 5.8 Delete Personal User Code 5 5.9 Delete All Personal User Codes 25 5.10 Volume Control 26 5.11 Factory Reset 6 6. Fingerprint Reader 27 6.1 Mounting the Fingerprint Reader 27 6.
Y ENTER | BL CLOTH ier a 6.6 Lock Door 31 6.7 Low-battery Indication 31 6.82 Setting Menu 31 6.9 Add User 32 6.10 Delete User 33 6.11 Enable/Disable User 33 6.12 Delete all Users 34 6.13 Add Time Schedule 34 6.14 Edit Time Schedule 35 6.15 Volume Control 35 6.16 Double Security 36 6.17 Factory Reset 36 7. Smartphone App 37 7.1 App Installation 37 7.2 Pairing Smartphone 38 8. Remote Control Battery Change 39 8.1 Battery Removal 39 8.2 Battery Insertion 40 9. Troubleshooting 41 10.
Y ENTER | BL CLOTH ier a i. Cylinder Installation 1.1 Package Content 1 Base plate & Knob 5 Battery charger 2 Electrical unit Magnet 3 Mounting screw Inside drive adapter 0 wh 4 Panel screw Mounting screws 9 Decorative spacer 10 Alien key #3 1.2 Tools Requirements e Small Phillips screwdriver Note: Do not use power tools or any excessive force to assemble ENTR® parts.
Y ENTER | BL CLOTH ier a 1.3 Prior to Installation Lori Remove knob screw using 1/16" Allen key and take the knob out. « Use a flat screwdriver to remove the cover. ® Remove both Allen screws entirely and remove internal mechanism. Note: While removing the internal mechanism secure the outside cylinder from falling. Consider using masking tape or similar. Knob Knob screw Cover 1.4 Unit Installation # Prior to installation check bolt locking direction.
Y ENTER | BL CLOTH ier a + Place the Inside drive adapter and tighten the screws. Do not over tighten the screws or use power tools. Adapter * Place decorative spacer over the Inside drive adapter, * Assemble base plate (top housing & knob). e Tighten cylinder mounting screw.
A + Carefully connect data cable plug. ENTER' ka¥ mae. oe Pres » Assemble electrical unit panel (battery housing). attache to base plate (1) and push down (2). = Tighten electrical unit panel screw. Electrical unit Data cable plug 1.5 Magnet Fitting Magnet Fitting: * Mount the magnet on the frame moldings, as close as possible to the lock. + The lower part of the magnet should align with the lower point of the slider (see illustration).
A 2. ENTR® Description 2.1 ENTR® Description ON/OFF switch Touch pad Indications Knob 2.2 Indications Mute Cfg Del Code MA Add ENTER' ka¥ mae.
A ENTER' ka¥ mae. oe Pres 2.3 ON/OFF Switch e Turning the ENTR® lock ON or OFF. 2.3.1 Switching the ENTR® ON Before turning ENTR® ON, verify that the door is shut. + Move the switch to the ON position. Make sure that the knob is in the zero position (see illustration). « Function and numeric buttons will all blink once. s Hazard beep sound will be emitted and error indication will blink once. # ENTR® is now in operating mode.
Y ENTER | BL CLOTH ier a 2.4 Initialization of the Lock Initiate the lock by touching the middies of the touch screen with the palm of your hand or fingers for 3 seconds. Mute Cfy Del « Programming buttons and battery status indication light will illuminate for 15 seconds, waiting for user's action. » After 15 seconds of inactivity, ENTR® will idle. 2.5 Default PIN Code The lock’s default factory PIN code is: 12345 # Please note: ® Default PIN code must be changed before starting the configuration process.
Y ENTER | BL CLOTH ier a 3. Operation 3.1 Changing PIN Code Warning: Do not attempt to operate the unit unit assembled on the door. ugh E a Touch screen with palm or fingers for Press [Code] Type [Default PIN code] 8 seconds to active, Numeric buttons illuminated. (12345) ug [# Mute Mute Cig Del Mute Cig Del Code MIA {OK] indication blinks once, Numeric buttons Illuminated Enter [ok] indication blinks once, 1 long beep emitted, {Mew PIN code] {4-10 digits) agp [# 1 long beep emitted.
Y ENTER | BL CLOTH ier a 3.2 Door Configuration The door configuration process sets your lock and door preferences. This process should be done after successful installation of the lock. It will take 15-20 seconds to complete. ng Important: Verify they the door bs Touch screen with palm or fingers Press [Cg] shut and no key is inserted into the for 3 seconds to active. cylinder during configuration steps.
Y ENTER | BL CLOTH ier a Hurd the door shut to avoid opening. {Chl Indication blinks, [Manual] indication Illuminated, The lock will carry cul the ‘Turn the knob manually to unlock {Cfg] indication blinks. configuration process. position and keep the door dosed. Note: if the configuration fails it take's 15-20 seconds to complete. Push on [Cig] refer to troubleshooting #1 Mute |Cfg| Del Open the door using the handle, Crass [Che] [GK] Indication blinks once.
) A [eve] ka¥ mae. oe Pres [Error] indication Illuminated, Magnet configuration failed 2 long beeps emitted. Refer to troubleshooting #2 1. You can still operate ENTR® in Manual mode (w/o automatic locking). 2. Remove any other magnets from the door. Mute Cfg Del 3. Place the magnet according to instructions. 4. Consult your installer or contact ENTR® Technical Support. Case, Mla Add Magnet Fitting: * Mount the magnet on the frame moldings, as close as possible to the lock.
Y ENTER | BL CLOTH ier a 3.3 Pairing Remote Control nigh { & Touch screen with palm or fingers for Crass [Add] Numeric buttons Ruminated. 3 seconds to active. Type [PIN code] gp ji] Numeric buttons blinking. Mute Mute Cfg Mute Cfg Del Code MIA Code Mls Press [1] to add remote control. Press the remote control button.
ENTER' Vie [orm] RIE. BE FREE [0] indication blinks once, foi] indication blinks for 15 seconds, 2 short beeps emitted, Ho beeps emitted, Remote control unl added. Start the process from sage 1. Mute Cfg Del Code M|& Add Notes: « To add more remote control units repeat this procedure. * A remote control unit can be paired with only one single door unit. ® [tis possible to add up to 20 remote control units. * Only authorized dealer can reset a paired remote. 3.
Y ENTER | BL CLOTH ier a ugh {Ded] blinks for 30 seconds. Press [Del] to confirm. [ese] indication blinks once. 2 short beeps emitted, Ruminated buttons tum off Mute Cig Del Mute Cfg bel Mute Cfg Del Code Mla Add Code Mla Hebe Code Mla Add Note: Wall reader and smartphone connected to the ENTR® lock will not be deleted. 3.5 Setting Sound Signal Turn the sound signal to OFF or ON ug Touch screen with palm or fingers for Press [Mute] [Lute] indication laminated. 3 seconds to active.
Y ENTER ma TICK Erm— 3.6 Setting Locking Mode Toggle between Automatic to Manual locking mode wg ugh Touch screen with palm or fingers for Press [MA] Type [PIN code] ugh ji] 3 seconds to active. Mute Cfg Del Mute Cig Del Mute Cfg Del Code Coda [Manual] indication Illuminated. Mute Cig Del Code MIA Add Notes: » Setting the ENTR® lock to Manual will disable automatic locking. e Follow the same procedure to set the ENTR® lock to Automatic locking.
A ENTER' ka¥ mae. oe Pres 3.7 Doorknob Operation Turn clockwise or counterclockwise to unlock. Beep sound emitted during doorknob operation. Important! When an active lock is opened by turning of the knob you must re-operate it by one of its automatic modes {i.e remote, phone, sliding your fingers, touch pad etc.) or else it will remain UNLOCKED. Knob operation is meant solely for mechanical override in the rare event it will not otherwise unlock. 3.
Y ENTER | BL CLOTH ier a 4. Touch pad Reader 4.1 Mounting the Touch pad Reader Select the location where the Touch pad Reader will be mounted. « Attach the Touch pad Reader base plate to the wall. + Use 4 screws and screw anchors, or double sided adhesive strip. 4.2 Battery Replacement 1. Release lid screw and open the lid. 2. Put in the batteries (2xAA) according to the signs. 3. Close the lid and tighten the screw. Notes: « After inserting the batteries the Touch pad Reader will turn on automatically.