Table of Content 1. Cylinder Installation 5 1.1 Package content 5 1.2 Tools required 5 1.3 Prior to installation 6 1.4 Cylinder & unit Installation 6 1.5 Magnet fitting 7 1.6 Cylinder to unit assembly (optional) 7 2. ENTR™ description 9 2.1 ENTR™ description 9 2.2 Indications 9 2.3 ON/OFF switch 10 2.3.1 Switching the ENTR™ ON 10 2.3.2 Switching the ENTR™ OFF 10 2.3.3 Low battery indication 10 2.4 Initiating the lock 11 2.
4. Touchpad Reader 19 4.1 Changing PIN code 19 4.2 Battery replacement 19 4.2.1 Low battery indication 19 5. Touchpad Reader operation 20 5.1 Operation 20 5.2 Pairing Touchpad Reader 20 5.3 Touchpad Reader master PIN code 22 5.4 Menu mode 22 5.5 Adding personal user code 22 5.6 Open door 23 5.7 Lock door 23 5.8 Delete personal user code 23 5.9 Delete all personal user codes 23 5.10 Factory reset 24 6. Fingerprint Reader 25 6.
6.6 Lock Door 31 6.7 Low-battery Indication 31 6.8 Setting Menu 31 6.9 Add User 32 6.10 Delete User 33 6.11 Enable/Disable User 33 6.12 Delete all Users 34 6.13 Add Time Schedule 34 6.14 Edit Time Schedule 35 6.15 Volume Control 35 6.16 Double Security 36 6.17 Factory Reset 36 7. Smartphone App 37 7.1 App Installation 37 7.2 Pairing Smartphone 38 8. Remote Control Battery Change 39 8.1 Battery Removal 39 8.
1. Cylinder Installation 1.1 Package content 1 Base plate & Knob 5 Battery charger 2 Electrical unit 6 Magnet 3 Mounting screw 7 Inside drive adaptor 4 Panel screw 8 Mounting screws 9 Decorative spacer 1.2 Tools required • • • • 2mm Allen key 3mm Allen key 5/32" Allen key Small flat screwdriver Note: Do not use power tools or any excessive force to assemble ENTR™ parts.
1.3 Prior to installation Warning: Do not attempt to operate the unit until assembled into the door • Remove knob screw using 1/16" Allen key and take the knob out. • Use a flat screwdriver to remove the cover. • Remove both Allen screws entirely and remove internal mechanism. Note: While removing the internal mechanism secure the outside cylinder from falling. Consider using masking tape or similar. Knob Cover Knob screw 1.4 Unit installation • • • • Prior to installation check bolt locking direction.
• Place the Inside drive adaptor and tighten the screws. Do not over tighten the screw or use power tools. Adaptor • Place decorative spacer over the Inside drive adaptor • Assemble base plate (top housing & knob). • Tighten cylinder mounting screw. Mounting screw Decorative spacer Base plate Note: In case the gear and the projecting rectangle are not aligned the unit will not be engaged to the knob.
• Carefully connect data cable plug. • Assemble electrical unit panel (battery housing). attache to base plate (1) and push down (2). • Tighten electrical unit panel screw. Panel screw 1 Electrical unit 2 Data cable plug 1.5 Magnet fitting Magnet Fitting: • Position the magnet on the frame. moldings, as close as possible to the lock. • The top point of the magnet should be Align with the lower point of the slider (see illustration).
2. ENTR™ description ON/OFF switch 2.1 ENTR™ description Touchpad Indications Knob 2.
2.3 ON/OFF switch • Turning the ENTR™ lock ON or OFF. OFF • ON 2.3.1 Switching the ENTR™ ON Before turning ENTR™ ON, verify that the door is shut. • Move the switch to the ON position. Make sure that the knob is in the zero position (see illustration). • Function and numeric buttons will all blink once. • Hazard beep sound will be emitted and error indication will blink once. • ENTR™ is now in operating mode. Note: • After turning ENTR™ ON, avoid touching the front panel until beep sound ends.
2.4 Initialization of the Lock Initiate the lock by touching the screen with the palm of your hand or fingers for 3 seconds. • Programing buttons and battery status indication light will illuminate for 15 seconds, waiting for user's action. • After 15 seconds of inactivity, ENTR™ will idle. 2.5 Default PIN Code The lock's default factory PIN code is: 1 2 3 4 5 # Please note: • Default PIN code must be changed before starting the configuration process.
3. Operation 3.1 Changing PIN code Warning: Do not attempt to operate the unit until assembled on the door. 1 Touch screen with palm or fingers for 3 seconds to active. 4 [OK] indication blinks once, 1 long beep emitted. Illuminated buttons turn off. 7 Numeric buttons illuminated Reenter [New PIN code] [#] For example: 1231234# 12 2 3 Press [Code] Numeric buttons illuminated.
3.2 Door Configuration The door configuration process sets your lock and door preferences. This process should be done after successful installation of the lock. It will take 15-20 seconds to complete. 1 2 Important: Verify that the door is shut and no key is inserted into the cylinder during configuration steps. 4 Touch screen with palm or fingers for 3 seconds to active. 3 Press [Cfg] 5 Numeric buttons illuminated, Type [PIN code] [#] 1 long beep emitted.
6 Configuration OK Hold the door shut to avoid opening. The lock will carry out the configuration process. It take's 15-20 seconds to complete. [Manual] indication illuminated. [Cfg] indication blinks. Note: If the configuration fails refer to troubleshooting #1 7 Open the door using the handle. Bring the latch as close as possible to the door frame. Note: Do not shut the door. Door moldings Magnet Configuration OK 8 Press [Cfg] The lock will carry out the configuration process.
Configuration failed [Error] indication illuminated, 2 long beeps emitted. Refer to troubleshooting #2 Troubleshooting #2 Magnet configuration failed 1. 2. 3. 4. You can still operate ENTR™ in Manual mode (w/o automatic locking). Remove any other magnets from the door. Place the magnet according to instructions. Consult your installer or contact ENTR™ Technical Support. Magnet Fitting: • Position the magnet on the door moldings, as close as possible to the lock.
3.3 Pairing Remote Control 1 Touch screen with palm or fingers for 3 seconds to active. 4 Press [1] to add remote control. Illuminated buttons turn off. [OK] indication blinks for 15 Seconds, waiting for remote control unit 2 3 Press [Add] Numeric buttons illuminated. Type [PIN code] [#] Numeric buttons blinking. 5 Press the remote control button.
Pairing OK [OK] indication blinks once, 2 short beeps emitted. Remote control unit added. Pairing failed [OK] indication blinks for 15 seconds, No beeps emitted. Start the process from stage 1. Notes: • To add more remote control units repeat this procedure. • A remote control unit can be paired with only one single door unit. • It is possible to add up to 20 remote control units. • Only authorized dealer can reset a paired remote. 3.
4 [Del] blinks for 30 seconds. Deletion accomplished 5 Press [Del] to confirm. [OK] indication blinks once. 2 short beeps emitted, Illuminated buttons turn off. Note: Wall reader and smartphone connected to the ENTR™ lock will not be deleted. 3.5 Setting Sound Signal Turn the sound signal to OFF or ON 1 Touch screen with palm or fingers for 3 seconds to active. 2 Press [Mute] 3 [Mute] indication illuminated. Sound signal is off.
3.6 Setting Locking Mode Toggle between Automatic to Manual locking mode 1 Touch screen with palm or fingers for 3 seconds to active. 2 Press [M A] 3 Type [PIN code] [#] 4 [Manual] indication illuminated. Notes: • Setting the ENTR™ lock to Manual will disable automatic locking. • Follow the same procedure to set the ENTR™ lock to Automatic locking.
3.7 Doorknob operation Turn clockwise or counterclockwise to unlock. Beep sound emitted during doorknob operation. Important! When an active lock is opened by turning of the knob you must re-operate it by one of its automatic modes (i.e remote, phone, sliding your fingers, touch pad etc.) or else it will remain UNLOCKED. Knob operation is meant solely for mechanical override in the rare event it will not otherwise unlock. 3.
4. Touchpad Reader 4.1 Mounting the Touchpad Reader Select the location where the Touchpad Reader will be mounted. • Attach the Touchpad Reader baseplate to the wall. • Use 4 screws and screw anchors, or double sided adhesive strip. 4.2 Battery Replacement 1. Release lid screw and open the lid. 2. Put in the batteries (2xAA) according to the "+" "-" signs. 3. Close the lid and tighten the screw. Notes: • After inserting the batteries the Touchpad Reader will turn on automatically.
5. Touchpad Reader Operation 5.1 Operation To turn the Touchpad Reader ON press [#] for 5 seconds. The reader will perform a self test followed by series of beeps. LED blinks Green, Red, Blue. 5.2 Pairing Touchpad Reader This procedure is done via the ENTR™ lock. See also: Pairing Remote Control. 1 Touch ENTR™ lock screen with palm or fingers for 3 seconds to active. 4 Press [1] to add Touchpad. Illuminated buttons turn off. [OK] indication blinks for 15 seconds waiting for the Touchpad.
Pairing OK [OK] indication blinks once, 2 short beeps emitted. Touchpad Reader added. Pairing failed [OK] indication blinks for 15 seconds, No beeps emitted. In wall reader: Green LED illuminated and 2 beeps emitted. Start the process from stage 1. • Hang the Touchpad Reader on the base plate. • Tighten fixing screw.
5.3 Touchpad Reader Master PIN Code 1 2 Touch screen with palm or fingers. Press [11] [#] 3 Enter [New master PIN code] (4-10 digits) [#] For example: 1231234# Master PIN code added Green [OK] illuminated for 1 second. 2 short beeps emitted. 5.4 Menu Mode Entering menu mode: Press [*] Reenter: [New master PIN code] [#] Master PIN code not added Red [Error] illuminated for 1 second. 1 long beep emitted. [Master PIN code] [#] 5.
5.6 Open Door 1 Not opening 2 Touch Reader screen with palm or fingers. Press [Personal PIN code] [#] Red [Error] illuminated for 1 second, 1 long beep emitted. 5.7 Lock Door 1 Not locking 2 Touch Reader screen with palm or fingers. Press [1] [#] Red [Error] illuminated for 1 second, 1 long beep emitted. 5.8 Delete PIN Code 1 2 Touch Reader screen with palm or fingers.
5.10 Volume Control 1 2 Touch Reader screen with palm or fingers. Press [*] [Master PIN Code] [#] Press [55] [#] Press [2] to increase the volume, or [8] to decrease the volume. Press [#] to confirm volume level. 5.11 Factory reset The reset action will delete all PIN codes (master and personal) and will cut off the Touchpad Reader from the ENTR™ lock. 1 2 Touch Reader screen with palm or fingers.
6. Fingerprint Reader 6.1 Mounting the Fingerprint Reader Prior to starting, select the location where the Fingerprint Reader is to be mounted. Avoid direct sun light to the front panel. • Attach the Fingerprint Reader base plate to the wall. • Use 4 screws and screw anchors or double sided glued tape. 6.2 Battery Replacement 1. Using a 2mm Allen key release the lid screw and open the lid. 2. Insert batteries (2xAA) according to the "+" "-" signs. Green LED will illuminate for 2 seconds. 3.
6.4 Pairing Fingerprint Reader This procedure is done via the ENTR™ lock. See also: Pairing Touchpad Reader. 1 2 Touch ENTR™ lock screen with palm or fingers for 3 seconds to active. 4 3 Press [Add] Numeric buttons illuminated. Type [PIN code] [#] Numeric buttons blinking. 5 Press [1] to add the reader. Illuminated buttons turn off. [OK] indication blinks for 15 seconds waiting for the reader. Touch Fingerprint Reader screen. 2 short beeps emitted. Press [OK] for YES or [*] to cancel.
6.4.1 Add Master User Setting a Master User requires both fingerprint and PIN code. It is possible to have up to two Master Users. Note: At any stage you can press and hold the [*] key to move to standby mode. MASTER #01 MASTERNAME JOHN JOHN Type in [Master name] [OK] 6.4.2 Set Finger Blue LED illuminates. Green LED blinking. ADD USER SWIPE SUCCESS 1st FINGER 1st FINGER SET FINGER Press [OK] Swipe 1st finger several times over fingerprint scanner until two confirmation beeps emitted.
• Hang the reader on the base plate. • Tighten fixing screw. Fixing screw 6.5 Unlock the Door OPTION 1: Place finger on fingerprint scanner. Short beep emitted & white LED is on. Swipe finger over fingerprint scanner Fingerprint authorized: Blue LED blinking and unlock command is sent. Fingerprint not authorized: Red LED is ON. The device goes to standby. OPTION 2: Touch the Fingerprint Touchpad. Screen shows user code. Enter your code [OK].
6.6 Lock the Door Touch the Fingerprint Touchpad Press [1] [#] 6.7 Low battery indication Warning signal blinking. Fingerprint Reader low battery indication Red LED illuminate for 1s after wake-up, 2 long beeps emitted. Door Unit low battery indication Low battery: Red LED illuminate for 1s after wake-up. Extremely low battery: Red LED illuminate for 1s after wake-up, 2 long beeps emitted. BATTERY LOW BATTERY LOW 6.
6.9 Add User The unit allows adding up to 20 users. For each user two different fingerprints and one PIN code. Use different user name for each user. 1 2 3 SETTING USERS USERS ADD USER Press [OK] Press [OK] 4 2nd MASTER? User name added USERNAME USER #08 JENNIFER JENNIFER *-NO OK-YES User name exist 5 USERNAME Choose [OK] to add 2nd Master User or [*] to add a user. Note: This screen will not appear if two Master Users are defined. 6 User name added.
6.10 Delete User USER CODE MASTER CODE SETTING ****** USERS Touch screen 1 23:49 03/01 23:49 03/01 Press [*] [OK] or Enter [Master PIN Code] swipe finger over fingerprint scanner 2 4 3 SETTING USERS DELETE USER USERS DELETE USER JENNIFER Press [OK] Use [8▼] or [2▲] to select user for deletion: [DELETE USER] [OK] User deleted SURE? *-NO OK-YES *-NO OK-YES Press [OK] Confirm deletion. DELETED JENNIFER Two beeps emitted, Green LED illuminates.
6.12 Delete All Users USER CODE MASTER CODE SETTING ****** USERS Touch screen 1 23:49 03/01 23:49 03/01 Press [*] [OK] or Enter [Master PIN Code] swipe finger over fingerprint scanner. 2 3 SETTING USERS USERS DELETE ALL Press [OK] Use [8▼] or [2▲] to select: [DELETE ALL] [OK] 4 All users deleted DELETE ALL? SURE? *-NO OK-YES *-NO OK-YES Press [OK] Press [OK] SUCCESS DELETED ALL Two beeps emitted. Green LED illuminates. 6.
6.14 Edit Time Schedule 1 2 3 4 5 SETTING USERS EDIT SCHED SUNDAY FRIDAY USERS EDIT SCHED SARAH 12:00-13:00 12:00-13:00 Press [OK] Use [8▼] or [2▲] to select: [EDIT SCHED] [OK] *-Back OK-Yes 6 7 Use [8▼] or [2▲] to toggle between users [OK] Use [8▼] or [2▲] to choose the desired schedule to be edited. Pressing on [4◄] for 3 seconds shall delete the specific schedule.
6.16 Double Security After activating the double security option use both methods - swiping a fingerprint and inserting a PIN code to unlock the door. Note: User set up with only one of the settings (fingerprint or PIN code) will not be able to unlock the door. USER CODE MASTER CODE SETTING ****** USERS Touch screen 1 23:49 03/01 23:49 03/01 Press [*] [OK] or Enter [Master PIN Code] swipe finger over fingerprint scanner.
7. Smartphone App 7.1 App Installation • Android smartphone users: go to Google Play to download the ENTR™ application. System requirements: Android 4.4 • iOS (iPhone/iPad) users: go to the app store to download the ENTR™ application. System requirements: iOS 7.0 or higher. • Bluetooth low-energy compliant. The below message will be displayed when opening the ENTR™ app prior to pairing it with your lock: "There are no available locks or keys within range".
7.2 Pairing a Smartphone This procedure is done via the ENTR™ lock door unit. 1 Touch the Door Unit screen with your palm or fingers for 3 seconds to activate. 2 Press [Add]. 3 Numeric buttons illuminate. Type [PIN Code] [#] Numeric buttons blink. 4 Press [2] to add a smartphone. [OK] indication blinks for 3 seconds. Illuminated buttons turn off, ENTR™ will be visible for 5 min. Open the ENTR™ app and follow the steps described in order to pair the smartphone with the ENTR™ lock.
8. Remote Control Battery Change 8.1 Battery Removal a. Release the lid by safely inserting a small tool into the notch (1), and press the lid clasp (2). Notch 1 2 Clasp b. Take out the push button and intermediate part. c. Take out the electronic board with the battery and remove battery.
8.2 Battery Insertion a. Insert new battery (CR2032) into the electronic board according to the "+" "-" signs (1). b. Insert the electronic board into the remote control’s housing (2). 2 1 c. Reassemble the intermediate part and the push button and place over the electronic board. d. Place the lid and press until the clasp clicks into place.
9. Sabbath Mode Auto-locking and hazard beeps after knob operation are disabled. Battery indication LED blinks every 20 seconds. 1 Touch screen with palm or fingers for 3 seconds to active. 4 Press [5] to toggle between activation and deactivation of the Sabbath mode. 2 3 Press [Cfg] Numeric buttons illuminated. Type [PIN Code] [#], Numeric buttons blinking.
10. Troubleshooting 10.1 Limitations and External Influences 1. Door position sensor might be influenced by external electromagnetic interference. 2. After mechanical key operation, the user should unlock and lock the unit electronically. 10.2 Cases New Unit Installation and Configuration Symptom Corrective action Page The unit isn't accepting my administrative code. Make sure the code you are using contains between 4-10 digits and is different from the "12345" factory code.
Constant Usage Symptom Corrective action Page ENTR™ has started double beeping whenever I lock or unlock the door. This is an indication your battery is low; it's time to charge the door unit. 31 The unit has started to beep constantly. 1. Place the knob in the zero position. 2. Please consult your locksmith or installer. 20 Sliders aren't responding as expected. Turn the unit off, wait for 3 seconds, and then turn it back on to reset it. 20 The touch panel isn't responding as expected.
Symptom Corrective action Page I have replaced the batteries, but when I press on "5", nothing happens. You need to first power-up the wall reader by pressing and holding the "#" button for 5 seconds. 27 My 5-year old son and his grandmother's fingerprints are no longer working with the fingerprint reader. Both children and the elderly have fingerprints that change. If this occurs, you'll have to repeat the fingerprint learning process for them. Alternatively, they can use a PIN code.
LIMITED WARRANTY Mul-T-Lock® hereby warrants, to the end user ("Purchaser") who purchased the genuine Mul-T-Lock® product (“Product"), from an authorized Mul-T-Lock® dealer (“Dealer”), that the Product will be free from defects in materials and workmanship ("Defects"), for a period of one year from the date the Product was purchased from Mul-T-Lock®’s authorized dealer.
THE USE OF OTHER THAN SUITABLE, GENUINE MUL-T-LOCK® COMPONENTS MAY CAUSE SEVERE DAMAGE TO THE PRODUCT, AND WILL VOID THIS LIMITED WARRANTY. THIS LIMITED WARRANTY MAY NOT BE ASSIGNED OR OTHERWISE TRANSFERRED IN ANY WAY AND MAY NOT BE EXTENDED, ALTERED OR VARIED.
Mobile phones LEGAL NOTICES ENTR™ warranty should not cover any problem related with end user mobile phone/ smartphone or its operation system, by connecting to ENTR™ lock or installing ENTR™ application. For any other limitation please refer to End User licence agreement.
For radio enclosure Federal Communications Commission (FCC) Statement Labelling requirement for small device statement (FCC15.19(3)) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Frequency Interference (RFI) (FCC 15.