/' """ ~ [:J ~ ~ ( ~I I~CUJ [O)D«::D .) w OWNER'S MANUAL THUNDER SERIES AMPLIFIERS Use your smartphone to scan or visit youtube.com/user/MTXThunderforce to learn how to properly install this amplifier. MTX.
PBODU CTINFO RMADO N Model# --------- --------- --------- ---Serial# _____ _____ _____ __ Dealer's Name ________ ________ _________ Date of Purchase ________ ________ _________ INJ"ROD UCJ"ION Thank you for purchasing this MTX Audio Hi-Performance amplifier. Proper installation matched with MTX speakers and subwoofers provide superior sound and performance for endless hours of enjoyment whether you are waking the neighbors or just out enjoying your tunes.
9. Bass Boost Level Switch (Mono Block)- This switch can boost bass level by OdB, 6dB, or 12dB. The boost frequency is centered at 50Hz. 10. High Pass Filter (Full Range)- This controls the frequencies played for the front channels. Low frequencies can be cut off from OFF to 200Hz. At OFF position, no low frequencies cut off, meaning full range. 11. X-Over Mode and Frequency Control (Full Range) -These controls allow control over the frequencies played for the rear channels.
PANEL IJIYOU7 Mono Block Amplifier Panel Layout THUNDER1000.1 I THUNDER500.1 0 D ~ 0 ~ 0 0 D THUNDER1000.1 +BATT 0 © D REM ~ 0 r-- 0 0 D THUNDER500.1 MTX.
WIRING DIAGRAM See page 26 for amplifier wiring diagrams. INSTALLATION AND MOUNTING MTX recommends your new THUNDER Series amplifier be installed by a 12 volt installation specialist. Any deviation from specified installation instructions can cause serious damage to the amplifier, speakers and/or vehicle's electrical system. Damage caused from improper installation is NOT covered under warranty. Please verify all connections prior to system turn on. 1. Disconnect the vehicle's negative battery cable. 2.
INSTALLATION For proper perfomance and safety, MTX recommends installing an in line fuse per the owner's manual instructions according to the following. TH UNDERl 000.1 100A Fuse THUNDER500.1 60A Fuse THUNDER75.
SPECIFICADONS Model Description THUNDER1000.1 THUNDER500.1 THUNDER75.4 1000 W RMS Mono 500 W RMS Mono 4x 75 W RMS RMS Power at 14.4V 1Q Load 1000W RMS NA NA 2Q Load 600W RMS 500W RMS 4 X 100W RMS 4Q Load 350W RMS 300W RMS 4x75WRMS 0.2- 5V 0.2- 5V 0.
WIRING DIAGRAifll Mono Block Amplifier Wiring (Single Subwoofer Load) @;:::=.=::::J------r=::==:J--c:::==:J--c::==>._@ ~© ©LQilQJ ·- ~ c::::r:b I ~ I @ l_ I FdsE ~ Re-mote Signal +&bl 1 Ohm Minimum (THUNDER1000.1 Only) lol · . . . . . . ,_, ,., _, _.,. Source Unit RCA Signal c=cb ~ q~ ~ ~ I FJSE ~ Re-mote Signal +&lol 2 Ohm Minimum ~.,.@ .
WIRING DIAGRAM Mono Block Amplifier Wiring (Multi-Subwoofer Load) NOTE: Equivalent parallel woofer load cannot be less than the minimum load rating. The two negative terminals are paralleled inside the amplifiers, as are the two positive terminals. These are monoblock amplifiers, not multi-channel amplifiers. The minimum load for the THUNDER500.1 amplifier is 2Q. The minimum load for the THUNDER1000.1 amplifier is 1Q.
WIRING DIAGRAIIII THUNDER75.4 Amplifier Wiring (4-Channel Mode) oe ~ ----------~f'~~ : ~,~ , --~-----------------+BATT REM GND o:;-o m ~ ~Roo © 9 0 <±;J L ,.e © f---H'"""- ©C!J ~o[J . <±>~Rie c:::=:=p~: ;: c::::;a=p ~ ~b :: ,'j . ~ ........,~~~~=-t"=;;;;;;;;;~~r~~-,~~~=ln oe 1 ~ ~ ot:::=:> i ~ @ F~sE 1 -!- +tl.
WIRING DIAGRAM THUNDER75.4 Amplifier Wiring (3-Channel Mode) oe ~ ; ~¥ ~ 11 · ~~~~~~~~~--~---------------~,~~~ I FUSE l +. I Remote Signal 4-0hm to 8-0hm RCA Signal @ I- I : L~7§ ~~NT 011~R ftm R 0 tR:.. ~~ FRONT REAR MiN MAx r 1 MiN MAx 1 Fk OFF 200H• 1 Fe.lg 1 r @ PWR LPF HPF SOH• 7SOH• TIIUIIIIIEII75_4 c::::::::::::> MTX.
FRONT REAR © 2012 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. MTX004553 RevA 11/12 NDM661 MTX.
Mitek Mobile Limited Warranty Our Guarantee Mitek Mobile products (including MTX, Streetwires, Coustic and Magnum) purchased in the USA after 1/1/2013 from an authorized Mitek retailer are guaranteed to be free from material defects in products and workmanship for five (5) years to the original end user purchaser, subject to the terms and conditions below.
No Other Warranties THE LIMITED WARRANTIES DESCRIBED ABOVE ARE EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. MITEK DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL WARRANTIES IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
