CONTENTS CX FLEX™ 4A PRODUCT MANUAL Product Manual for CX FLEX™ 4A WORKS WITH Contents 1. Materials in Box 2 2. Installation 3 3. Key Enrollment 4 4. Merchandising 4 5. Managing Alarms 5 6. Cable Removal 5 7. Remerchandising 5 8. Adding New User Keys 6 9. Deleting Enrolled Keys 6 10. LED Status Indicators 7 11. Dimensions 9 12. FCC and ISED Statement 10 DO NOT REMOVE FROM STORE For additional support, please reach out to our Contact Center at 800-426-6844 www.mtigs.
MATERIALS IN BOX CX FLEX™ 4A PRODUCT MANUAL CX Flex™ 4A Power Supply (400-00143) Use provided AC/DC adapter model W&T AD1806B050025U manufactured by W&T Electronics Co., Ltd. with output rating 5V d.c. 0.25A only. www.mtigs.com | T:800.426.
INSTALLATION CX FLEX™ 4A PRODUCT MANUAL 1 Feed power cable up through hole in fixture (if needed), 2 3 Clean the desired surface with an alcohol pad allow it to 4 Press down on the base plate for 20 seconds for full VHB and plug the barrel connector into the receptacle on the bottom of CX Flex, and plug the provided power supply into the nearest outlet. Use an outlet installed near the equipment that is easily accessible. completely dry. Peel the red film from the VHB adhesive. www.mtigs.
KEY ENROLLMENT CX FLEX™ 4A PRODUCT MANUAL 1 Place Authorization Card over the RFID icon to register to system. LED will be solid blue. 2 Place the User Key you want to add over the RFID icon. If successful unit beeps 2 times Repeat process for all User Keys until they are successfully added. 3 To close Enrollment mode, place the Authorization Card over the RFID icon. Enrollment mode will end automatically after 3 minutes of no use. LED will then be intermittently flashing white.
MANAGING ALARMS CX FLEX™ 4A PRODUCT MANUAL 1 To silence an alarm, hold the user card over the RFID icon. To disarm after silencing an alarm, hold the user card over the RFID icon again (2 + 4 beeps). Alarm events on any port will trigger an alarm, and the LEDs for the affected individual port or ports will flash red/white along with the system (side) LEDs. Other armed ports LEDs remain white.
ADDING NEW USER KEYS CX FLEX™ 4A PRODUCT MANUAL 1 From an armed state, place the User Key over the RFID icon to disarm the system. LED will be flashing white. 2 Place Authorization Card over the RFID icon. Follow Key Enrollment process starting on page 4. DELETING ENROLLED KEYS (This deletes all User Keys from the system.) 1 From an Armed state, place the User Key over the RFID icon to disarm the system. LED will be flashing white.
SYSTEM LED STATUS INDICATORS Visual Reference System Status Condition Solution System LEDs are solid white. Armed One or more ports of the pystem are armed. Some ports may be disarmed if they were not properly merchandised. System LEDs are flashing white. Disarmed System is disarmed and is ready to merchandise or re-arm. Alarming One or more ports of the system have triggered an alarm and require immediate attention, an alarm condition on any single channel will trigger the alarm.
SYSTEM LED STATUS INDICATORS Visual Reference System Status System LEDs are flashing blue. System LEDs are solid yellow. CX FLEX™ 4A PRODUCT MANUAL Condition Solution In Connect Pairing Mode; LEDs return to previous color when Pairing is complete; times-out after ~1.5 minutes. Connect Pairing Mode 1. Armed, paired with Connect,but not communicating to Connect Network 2. Delete User Keys Mode (If using Authorization Card) System LEDs are flashing yellow.
DIMENSIONS CX FLEX™ 4A PRODUCT MANUAL 1.04" [26.38mm] 2.43" [61.77mm] 4.60" [116.97mm] www.mtigs.com | T:800.426.
FCC AND ISED STATEMENT CX FLEX™ 4A PRODUCT MANUAL FCC ID: 2AA2X-15000252 Model: CX Flex 4A FCC Statement This device complies with Part 15 of the FCC Rules. Caution: If any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.