Installation and Maintenance Instructions Saf-T Vent® Model EZ Seal/EZ 316 and Model GC/GC 316 Single Wall Gas Vent Connector Chimney Liner & Special Gas Vent (USA) / Type BH Vent Class I/II (Canada) For Venting Residential, Commercial & Industrial Appliances Category I, II, III & IV Appliances Model EZ Seal/EZ 316 - 6”-16” Diameter Vent for use on Positive, Neutral and Negative Pressures up to 9” W.C. Model GC/GC 316 - 18”-32” Diameter Vent for use on Positive, Neutral and Negative Pressures up to 15” W.
APPLICATION INFORMATION Saf-T Vent Model EZ Seal/EZ 316 and Model GC/GC 316 Gas Vent Systems may be used to vent safety certified Category I, II, III, IV and Certain Direct Vent gas appliances with a flue gas temperature of not more than 550° F (288° C). When used as a masonry chimney liner, Saf-T Vent EZ Seal/EZ 316 (up to 10” diameter) can be used to vent condensing oil appliances and category I, II, III, IV gas fired appliances.
Clearance to Combustibles and Framing Requirements Table 1 shows the required MINIMUM AIRSPACE CLEARANCE TO COMBUSTIBLES. EZ Seal/EZ 316 - 6”-16” and model GC/GC 316 are primarily intended for installation in fire resistive, non-combustible surroundings or installed unenclosed. This airspace clearance is required for safe operation of the vent. Failure to follow these clearances could overheat the building materials and could cause fire.
Notes: 1. Unenclosed systems require at least one side open (combustible material on maximum of 3 sides). 2. Reduced clearances may be attained by using noncombustible enclosures. 3. Systems fully enclosed by combustible material are NOT permitted. 4. Do not place insulation in any required clearance spaces surrounding the vent system unless these instructions suggest otherwise and the insulation is specified or supplied. 5. Noncombustible enclosures require 0” air space.
2. The horizontal termination shall be located not less than 12 inches above grade or anticipated snow line (remember to consider snow and ice falling from overhead objects), and not less than 7 feet above grade when located adjacent to a public walkway. It shall also terminate a minimum of 4 feet below, 4 feet horizontally from, or 1 foot above any door, window, fresh air intake, utility meter or regulator unless the appliance is Listed differently.
c. After the sections are fully engaged, slide the lock ring down over the tabs, making sure all tabs are contained within the lock ring. d. Bend the tabs back over the lock ring to complete the joint. Note: Some termination parts have a hose clamp in place of the lock ring. In such cases, the hose clamp is tightened down over the tabs. The tabs need not be bent over the clamp. Model GC/GC 316 (Diameters 18" thru 32") is joined using Locking Strap the Locking Strap method.
Adjustable Length The Adjustable Length Section serves as a variable length between other components when specific lengths cannot be utilized and eliminates the need to cut parts to length. For proper installation, refer to instructions packaged with the Adjustable Length (See Fig. 7). Fig 7. (Adjustable Length) Customized Lengths— Cutting Standard Lengths The Saf-T Vent EZ Seal/EZ 316 system (6”-16”) is designed so that in most cases standard lengths will not need to be cut.
Saf-T Vent Fire Stop Wherever the vent passes through a ceiling or floor a Fire Stop (5x18CI) must be installed. To Install: Establish the correct framing dimension (See Table 1) and nail the Fire Stop to the joist (Fig 10a). Route the vent through the Fire Stop plate. Caution about insulation in attics – Note: The Fire Stop should be located on the top of the joist to prevent insulation from falling into the joist.
7. Using Silicone Sealant, seal any gaps between the wall, the Wall Penetration, the End Collar and Saf-T Vent. Wall Penetration & Horizontal Termination Wall Section The Wall Penetration & Horizontal Termination is Wall Penetration the standard Wall Penetration Assembly that Vent Pipe Vent Pipe includes a Horizontal Termination. To install: 1. Follow Steps 1-7 in the Wall Penetration FLOW Assembly Section. 2.
5. Install Cone on top of curb and bend down the extra material with duckbill pliers to create a cap which fits over the curb. 6. Attach the cone to the roof using common construction methods. 7. Install Vent pipe through the Tall Cone. Refer to corresponding section for instructions on installing the Storm Collar and Rain Cap (See Fig. 17B). Vent Pipe Pitched Roof Flashing The Pitched Roof Flashing is for vertical terminations through a Storm Collar non-combustible pitched roof.
Notes: PI-GCINS 4/17
Combustion & Ventilation Air: In order for appliances and their vent / chimney systems to operate properly they require a plentiful supply of clean combustion and ventilation air. Requirements for such combustion and ventilation air are found in the installation and maintenance instructions accompanying the appliance as well as in vent manufacturer's literature and various mechanical codes. Seek and follow guidelines provided there when installing an appliance / vent system.
Directives d’installation et d’entretien Saf-T Vent® Modèle EZ Seal Plus/EZ 316 et Modèle GC Plus/GC 316 Paroi simple connecteur d’évent à gaz, doublage de cheminée & évents aux gaz spéciaux (É-U) / évent de type BH pour appareils de catégorie I/II (Canada) Pour l’évacuation des appareils léger résidentiels et commerciaux pour appareils de catégorie I, II, III & IV.
INFORMATION D’APPLICATION Les systèmes d'évacuation de gaz Saf-T Vent modèle EZ Seal Plus/EZ 316 et modèle GC Plus/GC 316 peuvent être utilisés pour évacuer les appareils certifiés à gaz de catégorie I, II, III, IV et certains appareils à évacuation directe, dont la température des gaz de combustion ne dépasse pas 288°C (550°F).
Dégagement aux matériaux combustibles et encadrement exigés Le tableau 1 indique le DÉGAGEMENT MINIMAL REQUIS ENTRE L’ESPACE AÉRIEN ET LES MATIÈRES COMBUSTIBLES. EZ Seal Plus/EZ 316 – 6 à 16 pouces et le modèle GC Plus/GC 316 sont essentiellement destinés à être installés dans un enclos ayant une résistance incendiaire et non combustibles ou à être installés non cloisonnés. Ce dégagement d'espace aérien est nécessaire pour un fonctionnement sûr de l'évent.
Remarques: 1. Un système non cloisonné doit avoir au moins un côté ouvert (matériau combustible sur un maximum de 3 côtés). 2. Les dégagements réduits peuvent être obtenus en utilisant des enclos incombustibles. 3. Un système complètement cloisonné avec un matériau combustible n’est pas permis. 4. Ne placez pas d'isolant dans les espaces de dégagement requis autour du système d'évacuation, sauf si ces instructions suggèrent le contraire et que l'isolant est spécifié ou fourni. 5.
EXIGENCES D’INSTALLATION HORIZONTALE 1. 2. 3. 4. 5. Si la terminaison traverse un mur combustible, le système doit se terminer par une bague murale et une terminaison Saf-T Vent, tel que requis par le fabricant de l'appareil.
a. b. c. d. Pour raccorder, éloigner l'anneau de l'extrémité mâle pour permettre un dégagement pour les languettes de l'extrémité femelle. Engagez les deux sections en vous assurant que les languettes restent à l'extérieur de l'évent. Une fois les sections sont complètement engagées, glisser l'anneau vers le bas sur les languettes, en vous assurant que toutes les languettes sont contenues dans l'anneau. Repliez les languettes sur l'anneau pour terminer le joint.
Section ajustable La section de longueur ajustable sert de longueur variable entre autres pièces lorsqu’une longueur spécifique ne peut être utilisée et élimine le besoin de couper les longueurs au chantier. Pour l'installer, référez-vous aux instructions d'installation fournies avec la longueur ajustable. (Voir Fig. 7).
Coupe-feu Lorsque l'évent traverse un plafond ou un plancher, un coupe-feu (5x18CI) doit être installé. Pour l'installer : Déterminez la dimension exacte de l'encadrement (voir tableau 1) et clouez le coupe-feu à la solive (Fig. 10a). Faites passer l'évent à travers le coupe-feu. Attention à l'isolation dans les greniers - Remarque : lors de l'installation d'un coupefeu dans les combles, le coupe-feu doit être situé sur le haut de la solive afin d'éviter que l'isolation ne tombe dans la solive.
Virole murale et terminaison horizontale La virole murale et la terminaison horizontale est l'ensemble standard de virole murale qui comprend une terminaison horizontale. Pour l’installer: 1. Suivez les étapes 1 à 7 de la section pour virole murale. 2. Alignez la terminaison avec la virole murale de façon que la partie solide de l'écran soit tournée vers le haut. 3. Fixez la terminaison à la virole à l'aide de vis. 4.
6. Fixez le solin au toit à l'aide des méthodes de construction courantes. 7. Installez le tuyau d’évent à travers le solin plat. Référez-vous à la section correspondante pour les instructions d’installation du collet de solin et du capuchon (voir Fig. 17B). Solin de toit ajustable Le solin ajustable pour un toit incliné est destiné aux terminaisons verticales à travers d’un toit non-combustible.
Notes: PI-GCINS 4/17
La combustion et ventilation: Pour que les appareils et leurs systèmes d’évents fonctionnent adéquatement, ils nécessitent une offre abondante d’air frais ininterrompu pour la combustion et la ventilation. Les exigences requises pour air de combustion et de ventilation se trouvent dans les instructions d’installation et d’entretien du manufacturier de l’appareil ainsi qu’avec la documentation du fabricant de l’évent et les divers codes mécanique.