Home Theater Projector with Bluetooth INSTRUCTION MANUAL PJ-88BT Web site: www.Asnish.com Email: support@Asnish.
Important Safety Instructions 1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifier) that product heat. 9.
Additional Warnings and Precautions 1. Do not look directly into the projector light. 2. Don’t touch the project lens 3. Mains adapter is used as disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 4.
FCC Warning Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Table of Contents Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P1 Additional Warnings and Precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P2 FCC Warning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 In The Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - P3 Table of Contents - - - - - - - - - - - - - - - - - - - - - - - - -
Remove & Close The Lens Cover Remove the lens cover before using LENS COVER REMOVE Close the lens cover when unit is not using CLOSE LENS COVER OK OK Placing of Your Projector Your projector can be installed in four different configurations (see picture below): Front Table Rear Table Front Ceiling Rear Ceiling Front Table: Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.
To reduce Image Distortion • • Move the projector as close to the center of the screen as possible. The light beam from the projector should be perpendicular to the screen for a rectangular or square image. OK Distance Between The Projector And Screen Measure the distance between the projector and where you want to position the screen. This is the projection distance. SCREEN SIZE Distance 1.16m 1.35m 1.51m 1.79m 2.15m 2.81m 3.43m 4.
Adjust The Vertical Location Follow below picture to adjust the vertical location. SCREEN SCREEN VERTICAL DIMENSION PROJECTOR VERTICAL DIMENSION AV TF HDMI 1 HDMI 2 DC IN DC IN AV TF HDMI 1 HDMI 2 USB PROJECTOR SCREEN USB VERTICAL DIMENSION AV TF HDMI 1 HDMI 2 DC IN USB PROJECTOR Adjust this knob ( ANGLE ADJ. knob) to fine- tune the display angle to higher. Adjust The Focus And Keystone Follow below picture to adjust the focus and trapezoidal screen.
Controls of Remote Operation Indicator Mute Audio Sound Power ON/OFF Navigator Enter to Menu Exit the Menu Source Selector Increase Sound Volume Decrease Sound Volume Install / Remove Batteries of Remote Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (included), referring to the polarity markings. Finally, replace the cover.
Controls of Projector 1 3 Front View 4 Rear View VGA IR 2 Right Side View Top View 18 1516 17 5 6 19 20 DC IN AV TF HDMI 1 HDMI 2 OK 7 8 9 10 11 12 13 14 1 LENS 11 OK Button 2 ANGEL ADJ. Knob 12 RETURN 3 VGA IN Port 13 POWER 4 IR Sensor 14 POWER Indicator 5 FOCUS ADJ. Knob 15 EAR PHONE Jack 6 TRAPEZOIDAL ADJ.
Install Power Adapter Follow below picture to connect power adapter Connect small end of adapter FIRST. Plug the adapter body to power outlet. DC IN AV TF HDMI 1 HDMI 2 USB WARNING: Before connecting to the power supply, ensure that the supply corresponds to the information on the rating label at the back of the apparatus. Main Button Operation - Press the button to switch on unit, press again to turn off. / SOURCE - Press the button to select input source.
Connect HDMI Show The Image On Projector Screen Refer to the following picture to connect a set top box, a BD/DVD player or a streaming player to the HDMI input. 1. Turn off the unit before connect HDMI cable. 2. After connection, press the button to turn on unit and power indicator will light GREEN 3. Press the / SOURCE button to select HDMI 1 or HDMI 2 and the video from the connected device will be shown on projector screen. 4. Press the button to turn off unit power.
Connect VGA Show The Image On Projector Screen Follow below picture to connect VGA cable and device. 1. Turn off the unit before connect VGA cable. 2. Press the button to turn off power of your projector before connection. 3. After connect, press the button to turn on unit and power indicator will light GREEN 4. Press the / SOURCE button to select VGA mode and the video of VGA device will show on projector screen 5. Press the button to turn off unit power.
Connect Audio Output (Aux Out/Line Out/Earphones) Follow below picture to connect audio cable and device. 1. Press the button to turn off power of your projector before connection. 2. Use audio cable to connect follow below figure. 3. After connect and turn on both units. Your projector sound from external device now. 4.
Using TF Card And USB Playback (Media Player) Install USB / TF device: 1. Turn off the unit before install USB / TF card. 2. Install the USB device into USB port / Install the TF device into TF slot. 3. After connect, press the button to turn on unit and the power indicator light GREEN. 4. Press the / SOURCE button to enter and use buttons to search the USB or TF. 5. After selection, use buttons to search the PHOTO / MUSIC / MOVIE / TEXT icon and press the OK button to enter. 6.
Using Bluetooth Playback Pairing is the term used when two Bluetooth devices are connected wirelessly for the first time. This allows the devices to see each other and sets up a one to one communication channel between both devices. Bluetooth Connection 1. Press the button to turn on unit. 2. Press the /MENU button to enter the menu screen. 3. Use the button to select right side menu. 4. Use the button to select Bluetooth speaker column. 5. Press the 6.
Using Projector Menu 1 Press MENU button to enter projector menu. Picture Mode Standard Color Temperature Medium Aspect Ratio Auto Noise Reduction Middle PC Setting Reduce Display 100% USE TO SELECT Picture Mode Standard USE Use buttons to select different color temperature to Cool / Medium / Warm / User. Use or to select Red / Green / Blue digit If chose User item. Follow below figure. Use buttons to select screen ratio AUTO / 4:3 / 16:9. Follow below figure.
Using Projector Menu 2 Press MENU button to enter projector menu, press Sound Mode Standard Balance 0 Auto Volume Off Bluetooth Speaker Off USE TO SELECT Sound Mode Standard USE Ba lance 0 PRESS OK PRESS OK Use PRESS OK OK Press OK buttons to select Off / on. PRESS OK Press OK buttons to select Off / on. buttons to select Balance level to -50 to +50. TO SELECT Auto Volume Off USE This Sound menu showed on right upper of view screen.
Using Projector Menu 3 Press MENU button to enter projector menu, press OSD Language English Restore Factory Default ROTATE 0 OSD Duration 30S Software Update(USB) USE PRESS t OK Use buttons to select Y or N. If choose “Y” that your unit will go to factory default setting.