用户手册
EN......................................................................................................................................1 CH......................................................................................................................................7 Battery and Charging The MOZA Slypod comes with a built-in lithium battery. When charging for the first time, please fully charge the Slypod to activate the battery.
MOZA Slypod Overview Pan-tilt Head Pan-Tilt Lock Arca-Swiss Quick Release Tilt Knob Screw 1/4” and 3/8” Extension Hole Pan Knob Screw Quick Mounting Port Adapter (accessory) Quick Release Screw 1/4” Extension Hole Quick Mounting Port Indicator Light Power Button Quick Mounting Port Handle 1/4” Screw Hole Operation Button 3/8” Screw Hole 1 Charging Port
Mounting Mounting the handle Align the 1/4’’ screw hole on the handle with the 1/4’’ screw on the bottom of the pole, turn the handle clockwise to tighten it. Mounting the pan-tilt head Slide the pan-tilt head into the groove at the top of the pole, make part 1 and part 2 fully fit. Turn the screw ring 3 clockwise to secure the head onto the pole. Loosen the screw ring 3, then turn the knob screw 4 anticlockwise to detach the head from the pole. After the P&T head is detached,reset the quick release knob.
Getting Started Long press for 3 seconds: Power on/off Button Functions Power Button Photo taking control via the shutter cable Short press Elongate+ Device State Static Shorten- Start to elongate Start to shorten Elongate Accelerate by one gear Decelerate by one gear Shortened Decelerate by one gear Accelerate by one gear Short press power/+/- buttons(all three buttons) at the same time: Reset Power on Static Elongate Long press Shortened Elongate and continue to accelerate Shorten and
App Operation Note: It's required to active the device according to instructions before the first operation. please download the latest version. Updates are subject to change without notice. please note the major application stores Slide the operation point to any position, the device will move according to the sliding path.
Step Time-lapse Select step mode to set step length, cycle, residence time and step movement time. After the setting is completed, tap “Start” and the device will move according to the set step length, speed and cycle. Firmware Upgrade In the charging state, enter the APP interface after the device is connected to the APP, and select the Firmware Upgrade to perform the upgrading. The device must be restarted after the upgrade succeeds.
Specifications Slypod Storage Length:522mm(grip not included) Size Expanded Length:971mm Max Diameter:54mm Main Body: 745g Weight PTZ Head: 287g Grip:278g Payload Operating speed Vertical:9kg Horizontal:4Kg Highest:28mm/s Lowest:0.15mm/s Operating Voltage 8.5v - 12.6v Battery Life 120min Working Temperature -10℃ - 50℃ Communication Interface Bluetooth Battery Model Lithium ion Battery Battery Capacity 600mA/h Battery Voltage 11.
FCC Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
电池及充电说明 Slypod使用内置锂电池,首次充电使用时,请先给Slypod充满电以激活电池,保证产品顺 利使用。红灯常亮显示设备充电中,蓝灯常亮显示充电完成Slypod使用Type-C接口,手机 充电器、移动电源等都可以给Slypod充电,电池充满后将停止充电。 1.使用Slypod过程中,请使用包装内提供的原装充电线! 2.切勿过充、过放电池,否则将对电芯造成损害; 3.