User's Manual

ManualsBrandsMOZA ManualsElectronicsRS Steering Wheel

PASS

产品保修卡

产品型号

用户姓名

通讯地址

购买日期

用户电话

经销商信息（签章）

保修期

自购机日起，基座主体，方向盘，踏板和仪表显示屏保修12个月。设备外壳、说明书、线材、螺丝、扳

手、包装等不在"一年免费保修服务"范围内，但您可以选择有偿服务。

购买者在以下条件下不享受免费保修服务，但您可以选择有偿服务。

1. 超过三包有效期的；

2. 无三包凭证及有效发票的，但能够证明该产品在三包有效期内的除外；

3. 包修凭证上的型号与修理产品型号不符或者涂改的；

4. 非本公司特约维修人员拆动造成损坏的；

5. 因不可抗拒力造成损坏的；

6. 未按产品使用说明书要求使用、维护、保养而造成损坏的。

保修期限鉴于产品部位、不同国家法律法规等差异，将有所不同。相关国家与区域的保修期限，请

咨询MOZA官方或购买时联系的MOZA授权经销商。

产品保修条例

产品条码

正面

背面

· 光电磁吸双离合拨片

· RGB流水换档指示灯

· 24组可编程按键和旋钮

· 进口赛用级快拆

· 无线供电和通讯技术

1. 将方向盘快拆母头上6颗钢珠的位置与基座快拆公头的6个凹槽对应

2. 将快拆往盘面方向按压

3. 快拆将自动归位锁紧，若无归位，可尝试轻微转动盘面或取下后再安装

4. 如需拆取盘面，用双手捏住金色部分，同时拔出盘面

在MOZA Pit House软件中可以方便快捷地对方向盘进行设置。

· 下拨片模式：设置双离合拨片的模式，分别可设置为左右合成轴，左右独立轴和按键

· 转速随动：开启或关闭LED换档指示灯与转速的联动

· 指示灯显示模式：共分为模式一和模式二，当鼠标移动到选项上时会弹出详细解释

· 转速提示设置：根据转速与换档指示灯亮起的时机关系，分为提前型，标准型和极限型

· 颜色设置：可对每一颗LED单独进行7种颜色设置

· 亮度调节：调节换档指示灯的亮度

· 拨片校准：当拨片感应异常时，通过点击此处进行拨片校准

产品介绍

快拆使用方法

方向盘配置

将方向盘放置于平面上使盘面朝下，使用六角扳手取下换挡拨片触发杆一侧的螺丝，再用扳手

从磁吸拨片侧顶开插销（无需完全顶出，仅使磁吸拨片触发杆与插销可以分离即可），然后将静

音垫贴在磁铁孔背面和拨片触发杆背面凸起位置，如图示，最后将插销归位并装回螺丝

骨架材质：拉丝铝合金

面板材质：锻造碳纤维

后壳材质：航空级铝合金

拨片材质：3mm厚锻造碳纤维

尺寸：13英寸（325mm）

磁吸拨片：2个

双离合拨片：2个

机械键盘质感按键：10个

20段旋钮（可按压）：2个

万向摇杆（可按压）：2个

包装清单

产品参数

拨片接近块的安装

磁吸拨片静音垫的安装

User manual 使用说明书

Run all out while keeping the car under control

RS series steering wheel

RS 圆形方向盘 RS D形方向盘

（详细方向盘设置与功能，请访问MOZA Racing官网）

更多信息和教学视频请登录官网进行查阅

1. RS方向盘

2. 工具包：

六角螺丝刀

8mm铝合金接近块x4

M3x14螺丝x8

静音垫x4

使用螺丝工具包内的六角扳手将换挡拨片上的两颗螺丝取下，垫上增高块后用附带的长螺丝拧

紧，通过此垫片可将拨片与手的距离拉近8mm

赛车喇叭：1个

高亮LED RGB灯珠：10颗

LED色彩：7色自定义

智能遥测：支持

通过MOZA Pit House设置灯光：支持

拆装方式：D1赛车快拆

供电方式：无线

信号传输方式：无线

磁吸拨片感应方式：光电无接触式

磁吸拨片模式：双离合式/单离合式/开关式

· Dual-Clutch Photoelectric Magnetic Paddles.

· RGB Programmable Flow Shift Light.

· Advanced Programmable Buttons and Knobs.

· D1 Style Quick Release.

· Wireless Technology.

1. Aline the 6 steel balls on the steering wheel quick release female connector to the

corresponding 6 grooves on the base quick release male connector.

2. Press the steering wheel down to join the connectors.

3. Once locked check to ensure the steering wheel is connected to base by rotating the

wheel.

4. To remove the steering wheel, pull up the golden sleeve with both hands and remove the

steering wheel at the same time.

The steering wheel can be set conveniently and quickly in the MOZA Pit House Software.

· Down paddle mode: Set the mode of double clutch paddles, which can be set as left and

right composite axes, left and right independent axes and keys respectively.

· Speed follow-up: Turn on or off the linkage between LED shift indicator and speed.

· Indicator display mode: It is divided into mode 1 and mode 2. When the mouse moves

over the option, a detailed explanation will pop up.

· Speed prompt setting: It is divided into advance type, standard type and limit type.

according to the relationship between speed and the time when the shift indicator light is

on.

· Color setting: 7 colors can be set separately for each LED.

· Brightness adjustment: Adjust the brightness of the shift indicator.

· Dial calibration: click here to calibrate the dial when the dial sensing is abnormal.

Product Description

How to Use the Quick Release OR Quick Release Setup

Racing Wheel Conﬁguration

Place the steering wheel on a ﬂat surface with the surface facing down, use a hexagonal

wrench to remove the screw on one side of the shift paddle trigger rod, and then use a

wrench to push the pin from the side of the magnetic suction paddle (it is not necessary to

push the pin out completely, only to separate the magnetic suction paddle trigger rod and

the pin), and then stick the mute pad on the convex position on the back of the paddle

trigger rod, as shown in the ﬁgure. Finally, return the latch, and replace the screw.

Frame material: Brushed aluminum alloy.

Panel material: Forged Carbon Fiber.

Rear shell material: Aluminum alloy.

Paddle material: 3mm thick forged carbon ﬁber

Size: 13 inches (325mm).

Magnetic paddle: 2.

Double clutch paddles: 2.

Mechanical keyboard texture keys: 10.

20 Section knob (can be pressed): 2.

Universal rocker (can be depressed): 2.

Racing horn: 1.

Highlight led RGB beads: 10.

Packing List

Product Spec

Installation of Paddle Approach Block

Installation of Magnetic Suction Paddle Mute Pad

RS-O Racing Wheels R-D Racing Wheels

(for detailed steering wheel settings and functions, please visit the ofﬁcial

website of MOZA Racing)

For more information and teaching videos, please log in to the ofﬁcial website.

1. RS steering wheel

2. tool kit:

Hexagon screwdriver

8mm aluminum alloy approach block x4

Use the hexagon wrench in the screw kit to remove the two screws on the shift paddle,

add the heightening block, and tighten it with the attached long screw. Using this gasket,

the distance between the paddle and the hand can be shortened by 8mm.

LED color: 7-color custom.

Intelligent telemetry: Supported.

Lights setting via Moza Pit House:

Supported.

Steering Wheel Quick Release: D1

racing quick release.

Power supply mode: Wireless.

Signal transmission mode: Wireless.

Induction mode of magnetic paddle:

Photoelectric.

Magnetic suction paddle mode:

Double Clutch / Single Clutch / Switch.

尺寸：100*142mm

M3x14 screw x8

Mute pad x4

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Any Changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be

used in portable exposure condition without restriction.