NPort W2150A/W2250A Series Web Console: Serial Port Settings Flow control Default RTS/CTS Options None, RTS/CTS, XON/XOFF Description This field specifies the type of flow control used by the serial port. FIFO Default Enable Options Enable, Disable Description This field specifies whether the serial port will use the built-in FIFO. A 128-byte FIFO is provided to each serial port for both Tx and Rx directions.
9 9. Web Console: System Management The following topics are covered in this chapter: Overview System Management ¾ Misc.
NPort W2150A/W2250A Series Web Console: System Management Overview This chapter explains how to configure all settings located under the System Management folder in the NPort web console. System Management Misc. Network Settings Accessible IP List The Accessible IP List page is located under Misc. Network Settings in the System Management folder. This page is used to restrict access to the NPort by IP address. Only IP addresses on the list will be allowed access to the NPort.
NPort W2150A/W2250A Series Web Console: System Management SNMP Agent Settings The SNMP Agent page is located under Misc. Network Settings in the System Management folder. This page is used to configure the SNMP Agent on the NPort. SNMP Default Enable Options Enable, Disable Description This field enables or disables the SNMP Agent. If enabled, you will need to configure other SNMP Agent settings. You will need to enter a community name under Read community string.
NPort W2150A/W2250A Series Web Console: System Management Write Community String Default private Options free text (e.g., “private community”) Description This field specifies the write community string used for the SNMP Agent. This is a text password mechanism that is used to weakly authenticate changes to agents of managed network devices. SNMP Agent Version Default V1, V2c, V3 Options V1, V2c, V3 / V1, V2c / V3 only Description This field specifies which version(s) of SNMP to support.
NPort W2150A/W2250A Series Web Console: System Management Read/Write Privacy mode Default Disable Options Disable, DES, AES Description This field specifies whether data encryption will be used during read/write access. Read/Write Privacy Default Options free text (e.g., “read write key”) Description This field specifies the encryption key for read/write access, if read-/write privacy is enabled.
NPort W2150A/W2250A Series Web Console: System Management System Log Settings The System Log page is located under Misc. Network Settings in the System Management folder. This is where you select the type of events that will be logged by the NPort.
NPort W2150A/W2250A Series Event Web Console: System Management Description Cold start The NPort was powered on, or was restarted after a firmware upgrade. Warm start The NPort restarted without powering off. Console login auth fail An attempt has been made to open the web, Telnet, or serial console, but the password was incorrect. IP changed The IP address has been changed. Password changed The password to the console has been changed.
NPort W2150A/W2250A Series Web Console: System Management E-mail Alert The E-mail Alert page is located under Auto Warning Settings in the System Management folder. This is where you specify how and where e-mail is sent when e-mail is used for automatic notification of system and serial port events. ATTENTION Consult your network administrator or ISP for the mail server settings to use for your network. If these settings are not configured correctly, e-mail notification may not work properly.
NPort W2150A/W2250A Series Web Console: System Management SNMP Trap The SNMP Trap page is located under Auto Warning Settings in the System Management folder. This is where you specify the SNMP trap settings to use for automatic notification of system and serial port events. SNMP Trap Server IP Default Options IP address (e.g., “192.168.5.5”) Description This field specifies the IP address of the SNMP trap server that will receive SNMP traps.
NPort W2150A/W2250A Series Web Console: System Management Maintenance Console Settings The Console Settings page is located under Maintenance in the System Management folder. This is where you enable or disable access to the various NPort configuration consoles, as well as the behavior of the reset button. You may modify HTTP console, HTTPS console, Telnet console, SSH console, Serial Console, and Reset button.
NPort W2150A/W2250A Series Web Console: System Management Ping The Ping page is located under Maintenance in the System Management folder. It provides a convenient way to test an Ethernet connection or verify an IP address. Enter the IP address or domain name in the Destination field and click [Activate]. The results will be displayed immediately. Firmware Upgrade The Firmware Upgrade page is located under Maintenance in the System Management folder. This is where you can update the NPort firmware.
NPort W2150A/W2250A Series Web Console: System Management Configuration Import The Configuration Import page is located under Maintenance in the System Management folder. This is where you can load a previously saved or exported configuration. Select or browse for the configuration file in the Select configuration file field. If you also wish to import the IP configuration (i.e., IP address, netmask, and gateway), make sure that Import all configurations including IP configurations is checked.
NPort W2150A/W2250A Series Web Console: System Management Load Factory Default The Load Factory Default page is located under Maintenance in the System Management folder. Click [Submit] to reset all settings to the factory defaults. You can preserve the NPort’s existing IP settings (i.e., IP address, netmask, gateway, WLAN profile, and all certificates) by making sure Keep IP settings is checked before clicking [Submit].
NPort W2150A/W2250A Series Web Console: System Management ATTENTION If you forget the password, the ONLY way to configure the NPort is by loading the factory defaults with the reset button. All settings will be lost. Before setting the password, you may want to first export the configuration to a file. Your configuration can then be easily imported back into the NPort if necessary.
NPort W2150A/W2250A Series Web Console: System Management WLAN SSL Certificate Import The WLAN SSL Certificate Import page is located under Certificate in the System Management folder. By default, the WLAN SSL certificate is automatically generated by the NPort based on the IP address of the wireless interface. You can also import a certificate. Select or browse for the certificate file in the Select SSL certificate/key file field.
NPort W2150A/W2250A Series Web Console: System Management You must install the trusted server certificate from the RADIUS server in order to enable Verify server certificate in the WLAN Security settings. This certificate will then be used by the NPort to authenticate the RADIUS server. WPA User Certificate Import The WPA User Certificate Import page is located under Certificate in the System Management folder. This is where you can load the WPA user certificate.
NPort W2150A/W2250A Series Web Console: System Management The WPA User Key Import page is located under Certificate in the System Management folder. This is where you can load the WPA user certificate. Select or browse for the user private key file in the Select WPA user privacy key file field and enter the Password for the private key. The user private key of the NPort must be installed in the RADIUS server when the NPort uses WPA(WPA2)//TLS.
10 10.
NPort W2150A/W2250A Series Web Console: System Monitoring Overview This chapter explains how to use the System Monitoring functions on the NPort web console. These functions allow you to monitor many different aspects of operation. System Monitoring Serial Status Serial to Network Connections The Serial to Network Connections page is located under Serial Status in the System Monitoring folder. On this page, you can monitor the current operation mode and host connection status for each serial port.
NPort W2150A/W2250A Series Web Console: System Monitoring Serial Port Status The Serial Port Status page is located under Serial Status in the System Monitoring folder. On this page, you can monitor the signal and data transmission status for each serial port.
NPort W2150A/W2250A Series Web Console: System Monitoring Serial Port Settings The Serial Port Settings page is located under Serial Status in the System Monitoring folder. On this page, you can view the current communication settings for each serial port.
NPort W2150A/W2250A Series Web Console: System Monitoring The Network Connections page is located under System Status in the System Monitoring folder. On this page, you can view the current status of any network connection to the NPort. Serial Data Log Data logs for each serial port can be viewed in ASCII or HEX format. After selecting the serial port and format, you may click Select all to select the entire log if you wish to copy and paste the contents into a text file.
NPort W2150A/W2250A Series Web Console: System Monitoring System Log The System Log page is located under System Status in the System Monitoring folder. This is where you can view the log of NPort system events. Click [Clear log] to clear the log contents. Click [Refresh] to refresh the log contents. WLAN Log (This function is supported by firmware V1.10 or above) The WLAN Log page is located under System Status in the System Monitoring folder.
NPort W2150A/W2250A Series Web Console: System Monitoring WLAN Status The WLAN Status page is located under System Status in the System Monitoring folder. This is where you can view the current WLAN settings and status.
11 11.
NPort W2150A/W2250A Series Web Console: Restart Overview This chapter explains how to use save your configuration changes and restart the NPort using the NPort web console. Configuration changes will not be effective until they are saved and the NPort is rebooted. Restart Restart System The Restart System page is located in the Restart folder. Click [Restart] to restart the NPort, and the new settings will take effect upon restart.
NPort W2150A/W2250A Series Web Console: Restart Restart Ports The Restart Ports page is located in the Restart folder. Select the desired serial and click [Select All] to select all serial ports. Click [Submit] to restart the selected serial ports.
12 12.
NPort W2150A/W2250A Series Android API Instructions Overview If you want to remote control your serial devices on an Android platform, then the MxNPortAPI is a simple application programming tool that you can use. The MxNPortAPI helps programmers develop an Android application to access the device server by TCP/IP. The MxNPortAPI provides frequently used serial command sets like port control, input/output, etc., and the style of developed Android application is similar to MOXA Driver Manager.
NPort W2150A/W2250A Series Android API Instructions For more details about the installation, please refer to the Overview section.
NPort W2150A/W2250A Series Android API Instructions byte[] buf = {'H','e','l','l','o',' ','W','o','r','l','d'}; mxNPort.open(); /*open port*/ mxNPort.setIoctlMode(mode); /*serial parameters setting*/ mxNPort.write(buf, buf.length); /*write data*/ mxNPort.close(); /*close port*/ } catch (MxException e){ /*Error handling*/ } } } }; thread.
A A. SNMP Agents with MIB II & RS-232-Like Groups The NPort has built-in SNMP (Simple Network Management Protocol) agent software that supports SNMP Trap, RFC1317 RS-232 like groups and RFC 1213 MIB-II. The following table lists the standard MIB-II groups, as well as the variable implementation for the NPort.
NPort W2150A/W2250A Series SNMP Agents with MIB II & RS-232-Like Groups ICMP MIB IcmpInMsgs IcmpInTimestamps IcmpOutRedirects IcmpInErrors IcmpTimest ampReps IcmpOutEchos IcmpInDestUnreachs IcmpInAddrMasks IcmpOutEchoReps IcmpInTimeExcds IcmpOutMsgs IcmpOutTimestamps IcmpInParmProbs IcmpOutErrors IcmpOutTimestampReps IcmpInSrcQuenchs IcmpOutDestUnreachs IcmpOutAddrMasks IcmpInRedirects IcmpOutTimeExcds IcmpOutAddrMaskReps IcmpInEchos IcmpOutParmProbs IcmpInEchoReps IcmpOutSrcQuench
NPort W2150A/W2250A Series SNMP Agents with MIB II & RS-232-Like Groups RFC1317: RS-232 MIB Objects Generic RS-232-like Group rs232Number RS-232-like General Port Table rs232PortTable rs232PortEntry rs232PortIndex rs232PortType rs232PortInSigNumber rs232PortOutSigNumber rs232PortInSpeed rs232PortOutSpeed RS-232-like Asynchronous Port Group rs232AsyncPortTable rs232AsyncPortIndex rs232AsyncPortStopBits rs232AsyncPortEntry rs232AsyncPortBits rs232AsyncPortParity rs232InSigTable rs232InSigPortIndex
B B. Well-Known Port Numbers Listed below are Well-Known Port Numbers that may cause network problems if they are assigned to an NPort serial port. Refer to RFC 1700 for Well-Known Port Numbers or refer to the following introduction from IANA. The port numbers are divided into three ranges: Well-Known Ports, Registered Ports, and Dynamic and/or Private Ports. • Well-Known Ports range from 0 through 1023. • Registered Ports range from 1024 through 49151.
NPort W2150A/W2250A Series UDP Socket Application Service 0 reserved 2 Management Utility 7 Echo 9 Discard 11 Active Users (systat) Well-Known Port Numbers 13 Daytime 35 Any private printer server 39 Resource Location Protocol 42 Host name server (names server) 43 Whois (nickname) 49 Login Host Protocol (Login) 53 Domain Name Server (domain) 69 Trivial Transfer Protocol (TETP) 70 Gopher Protocol 79 Finger Protocol 80 World Wide Web HTTP 107 Remote Telnet Service 111 Sun
C C. Ethernet Modem Commands A serial port on the NPort can be set to Ethernet Modem mode, allowing a PC or device to connect to the NPort as if it was an Ethernet modem. This section provides additional detail about how the NPort operates in Ethernet Modem mode. Dial-in Operation The NPort can listen for a TCP/IP connection request from a remote Ethernet modem or host. The NPort’s response depends on the ATS0 value, as follows.
NPort W2150A/W2250A Series Ethernet Modem Commands AT Commands Ethernet Modem mode supports the following common AT commands, as used with a typical modem: No. Command Description 1 ATA Answer manually 2 ATD Remarks Dial up specified IP address and port number ATD 192.168.1.
NPort W2150A/W2250A Series Ethernet Modem Commands S Registers No.
D D. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
NPort W2150A/W2250A Series Federal Communication Commission Interference Statement Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1. This device is intended for OEM integrators only. 2. Please see the full Grant of Equipment document for other restrictions.
E E. FCC Warning Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.