User's Manual

ManualsBrandsMovita Technologies ManualsElectronicsExternal USB Combo Drive

Notice: The changes or modifications not expressly approved by the

party responsible for compliance could void the user’ s authority to

operate the equipment.

Federal Communications Commission (FCC) - Notebook

The Federal Communication Commission Radio Frequency

Interference Statement includes the following paragraph:

This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However there is no guarantee

that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

q Reorient or relocate the receiving antenna.

q Increase the separation between the equipment and the receiver.

q Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

q Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and shielded AC power cable must be

employed with this equipment to insure compliance with the pertinent

RF emission limits governing this device. Changes or modifications not

expressly approved by the system’ s manufacturer could void the user’ s

authority to operate the equipment.

SA FETY & C O MPLIANC E

Summary of content (12 pages)

PAGE 1
SAFETY & C O MPLIANC E Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Federal Communications Commission (FCC) - Notebook The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: q This device may not cause harmful interference. q This device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission (FCC) – Fax/modem This equipment complies with Part 68 of the FCC Rules.
PAGE 3
Canadian Department of Communications-Notebook This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.
PAGE 4
UL/TUV Battery & FAX/Modem Caution and Important Safety Instructions CAUTION "CAUTION-To reduce the risk of fire, use only No.26 AWG or large telecommunication line cord." "CAUTION-Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment." Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’ s instructions.
PAGE 5
CTR21 Notice The equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.
PAGE 6
CE Declaration of Conformity The system computer model H300 and accessories conform to the following production specifications: Manufacturer Name: Manufacturer Address: Model Name: OD-100 Is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member Sates relating to Electromagnetic Compatibility (89/336/EEC) and Lowvoltage Directive (73/23/EEC & 93/68/EEC).
PAGE 7
1995/ A1:2000 IEC 61000-4-6 : 1996/ A1:2000 RF Common Mode requirements IEC 61000-4-8 : 1993/ A1:2000 Power Frequency Magnetic Field requirements IEC 61000-4-11 : 1994/ A1:2000 Voltage Interruptions and Voltage Dips requirements 73/23/EEC-Low Voltage Directive EN 60950 1992 +A1+A2+A3+A4+A 11 Safety for information technology equipment including electrical business equipment The following manufacturer/importer is responsible for this declaration: Company Name: Company Address: Person responsible for
PAGE 8
Package Content OD-100 series External USB 2.0 optical drive package should contain the following, if any of the items is damaged or missing, please contact your retailer immediately for the replacement. - OD-100 series optical CD drive - USB 2.0 cable - Power cable and adapter - Multi-language user’ s manual NOTE: This applies to the retail box. Your drive may have been shipped in a different box with other contents, depending on whom you purchased the drive from and what they included inside the box.
PAGE 9
Specifications The OD-100 series has the following specifications, Chipset CYPRESS CY7C68300 Interface Access Time USB2.0 / 1.1 72ms (1/3 stroke) Optical Device ODC-100 (CD-ROM) 12.7mm height ODR-100 (CD-RW) 12.7mm height ODV-100 (DVD-ROM) 12.7 mm height ODB-100 (Combo) 12.
PAGE 10
Features - USB2.0 interface - Operate at high (480Mbps) or full (12Mbps) speed. - Comply with T13s ATA/ATAPI-6 Draft specification. - Support PIO modes 0, 3, 4, and UDMA modes 2, 4, - ATA interface IRQ signal support. - Support for ATA/ATAPI devices configured either master or slave. ODB-Drive Controls Front panel 1 Tray front door: Attached to tray drawer. 2 LED indicator: Green: Power is on and a disc in the drive . Blinking greenr: Reading or Writing data to disc.
PAGE 11
4 Eject button: Push once to eject tray. Push again to insert the tray back into the OD-100. To prevent wear on the drive, always use the eject button to insert the tray. Rear Panel 1 Power switch: switch to turn power on or off. 2 Power connector: Connect the AC adapter here. CAUTION: Use the AC adapter shipped with your OD-100 Series. 3 USB connector: Connect the USB cable here. CAUTION: Use the USB cable shipped with your OD-100 Series. 4 Volume control: Controls volume of headphone jack.
PAGE 12
1 Power indicator Red: Power is on 2 Busy singal indicator . Blinking amber: Reading or Writing data to disc. Installing your OD-100 1. Turn ON your computer system. 2. Connect the AC adapter to your OD-100. 3. Turn the PlexWriter’ s power switch ON 4. Connect the USB cable from your OD-100 drive to the computer. The drive will be automatically recognized by the system.