Table Of Contents Chapter 1：Introduction ………………………………….. ……..1 -1 Welcome ……………………………. ……………………………………. . ………1 -1 To Open the Notebook. ……………. . ……………………………………. . ……. . 1-1 Taking a look at this Notebook ……………………………………………. ……. . 1-2 Front View …………………………………………………………………………1 -2 Left View …………………………………. . ……………………………………. . . 1-3 Right View ………………………………………. . ………………………………. 1-4 Rear View ……………………………………………. . …………………………. 1-4 Bottom View ………………………………………………. . …………………….
Inserting and removing a CD……………………………………………………2 -8 Using the Floppy Disk Drive ………………………. ……………………………. . 2-9 Using the Hard Disk Drive………………………………. . ………………………. 2-9 Using the Utility CD…………………………………………. . …………………. 2-10 Chapter 3：Power Management ………………………………..3 -1 About the AC Adapter ……………………………………. ………………………. 3-1 Using the Battery Pack……………………………………………………………3 -2 To Change the Battery Pack …………………………………. . ………………. 3-2 Battery Charging………………………………………………………………….
SAFETY & C O MPLIANC E Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Federal Communications Commission (FCC) - Notebook The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: q This device may not cause harmful interference. q This device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission (FCC) – Fax/modem This equipment complies with Part 68 of the FCC Rules.
Canadian Department of Communications-Notebook This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.
UL/TUV Battery & FAX/Modem Caution and Important Safety Instructions CAUTION "CAUTION-To reduce the risk of fire, use only No.26 AWG or large telecommunication line cord." "CAUTION-Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment." Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’ s instructions.
CTR21 Notice The equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.
CE Declaration of Conformity The system computer model H300 and accessories conform to the following production specifications: Manufacturer Name: Manufacturer Address: Model Name: H300 Is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member Sates relating to Electromagnetic Compatibility (89/336/EEC) and Lowvoltage Directive (73/23/EEC & 93/68/EEC).
1995/ A1:2000 IEC 61000-4-6 : 1996/ A1:2000 RF Common Mode requirements IEC 61000-4-8 : 1993/ A1:2000 Power Frequency Magnetic Field requirements IEC 61000-4-11 : 1994/ A1:2000 Voltage Interruptions and Voltage Dips requirements 73/23/EEC-Low Voltage Directive EN 60950 1992 +A1+A2+A3+A4+A 11 Safety for information technology equipment including electrical business equipment The following manufacturer/importer is responsible for this declaration: Company Name: Company Address: Person responsible for
Chapter 1：Introduction Welcome Thank you for purchasing this notebook computer. The state-of-the-art computer is slim and ultra light, and possesses the abilities of high powerful data computing and advanced 2/3D graphics acceleration. It supports a variety of expansible function for expanding memory, Hard disk and so on. Also, wherever you need it, the computer is easy to go.
Taking a look at this Notebook This section describes the function of the notebook. Note：Depending on the model of you purchased, the appearance of the notebook may not exactly the same as those shown in this manual. Front View 1. 10.4” LCD Screen This computer supports 10.4” TFT LCD panel. 2. Right Speaker (P.2-6) 3. Keyboard (P.2-4) 4. Touch pad (P.2-5) 5. External Microphone Port Connects an external microphone. (P.2-6) 6. External Audio Port Connects external Audio devices, e.g.
8. Power Indicators Indicating the power status of this computer. (P.2-3) 9. Internal Microphone (P.2-6) 10. Power Button To turn the computer ON or OFF. 11. Left Speaker (P.2-6) Left View 1. PC Card Slot To load pc card for expanded functions. (P.5-1) 2. USB 2.0 Port Connects the USB Devices. (P.5-3) 3. LAN Port To connect LAN by RJ-45 LAN wire. (P.2-7) 4. Communication Port To used Modem for telecommunication by RJ-11 phone line. (P.2-7) 5.
Right View 1. DC-IN Port Connects the AC adapter. (P.2-1) 2. Airflow Vent Holes Note： Please keep the vent holes well aired to prevent overheating of the notebook. 3. Internal Hard Disk This notebook computer allows one 2.5-inch IDE (Integrated Drive Electronics) hard disk drive. (P.5-4) Rear View 1. Battery Pack (Li-lon) This notebook computer supports one rechargeable Li-lon battery. It supplies power to the computer when external power is not connected. (P.
Bottom View 1. CPU Fan The CPU fan to prevents overheating of CPU. 2. DDR RAM Cover Inside is the DDR RAM slot for expanding the memory size of the notebook computer. (P.5-4) 3. Battery Lock Latch Please follow an arrow imprinted to lock or unlock internal battery.
Chapter 2：Operating The Notebook This chapter provides information about the use of the notebook. Getting the Computer Running Connecting Power to the System This notebook computer runs on its rechargeable battery. You can also plug its AC adapter into a wall socket for continuous high-performance operation or battery recharge. It is suggested that you use AC power when you start up the computer for the very first time.
3. Plug the direct current cable from the AC adapter into the DC-IN port on right side of the notebook. 4. The indicator on the front edge of the notebook will begin flashing with a green light. This indicates that the AC adapter has begun charging the internal battery. Note: It is particularly important that you give your battery a full charge the first time that you use it. We recommend that you leave the system connected to the AC adapter until the battery is fully charged.
About Power Indicators The two power indicators are located on the front edge of the notebook base. Power Indicator Steady：System is ON Flashing：System is suspended Battery Charge Indicator Steady：Battery is fully charged Flashing：Battery is charging About the Status Indicators The four status indicators, from left to right, are：Hard Disk, Num Lock, Caps Lock and Scroll Lock. Indicator Hard Disk Icon Description (Light On) Write data to hard disk or read data from hard disk.
About the Keyboard The exact layout of your keyboard depends on the language/system you’ re using. Displayed here is a standard US/Windows keyboard. The table below shows the meaning of the function key icon, and other embedded keyboard icons： Keystrokes Icon Description FN + F2 Serves as the sleep button that you can define with Windows “ Power Management” . (See the “ Using Power Management” in Chapter 3) FN + F6 This key combination turns off the volume of the speakers.
Chapter 3：Power Management This chapter tells you how to use power management and delivers the information about AC adapter, Internal battery pack. About the AC Adapter The AC adapter serves as a converter from AC (Alternating Current) to DC (Direct Current) power because your computer runs on DC power, but an electrical outlet usually provides AC power. The AC adapter is Auto-sensing so that your notebook can operate through the AC adapter connected to any available power supply in a wall outlet.
Note： The AC power cord supplied with your notebook computer is for use in the country where you purchased your notebook computer. If you plan to go overseas with the notebook computer, consult your dealer for the appropriate power cord. Using the Battery Pack The battery pack contains Lithium-Ion (Li-lon) that can be installed in the rear side of the computer. Warning： Only use the battery pack that is supplied with this notebook.
Battery Low Warnings Your notebook will alert you to a low battery condition by emitting a continuous beeping sound. This warning happens when the battery has only 15% of total charge remaining. If you continue using your computer after the battery low warning, the notebook will continue to operate normally until the charge level drops to around 5% of total charge. At this point, without warning, the notebook will automatically turn off the system.
disk is quickly read back into memory. In just a few moments, your computer appears exactly as it was when you last hibernate. Hibernate is very useful for Windows users who like to have many different programs open on the Windows desktop. You can take quite a few minutes to get a busy Windows desktop up and running, and then you have to shut down each program one by one when you want to turn off your computer.
Chapter 4: Configuring the Notebook With the BIOS Setup program, you can modify BIOS settings and control the special features of your computer. The Setup program uses a number of menus for making changes and turning the special features on or off. Using the System Configuration Utility To start the BIOS Setup utility: 1.Turn on or reboot your system. The BIOS displays this message: Press to enter SETUP 2.
The Legend Bar Use the keys listed in the legend bar on the bottom to make your selections or exit the current menu. The chart on the following page describes the legend keys and their alternates: Key or Ö Arrow keys ↑ or ↓ arrow keys or or or or <-> or <+> or Function General Help window (See below). Exit this menu. Select a different menu. Move cursor up and down. Cycle cursor up and down.
Main Menu Selections Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help System Time System Date: [16:19:20] [02/10/2002] 4Primary Master [19077MB] 4Memory Cache Quick Boot Bootl-Time Diagnostic Screen [Enabled] [Enabled] CPU Type CPU Speed VIA Ezra 933MHz System Memory Extended Memory 640KB 228352KB F1 Help ESC Exit ↑ ↓ Ö , , or selects field Select Item -/+ Change Values Select Menu Enter Select 4Sub-Menu F9 Setup Defaults F
None – Autotyping is not able to supply the type or no hard disk is installed. User – This allows you to fill the hard-disk drive information in the Cylinders, Heads and Sectors/Track fields. It automatically calculates “ size” based on this information. LBA Mode Control – “ Enable” is default setting, because most hard disks capacity is larger than 528MB. 32-Bit I/O – Most new hard disks can support this higher rate. Enables 32-bit communication between CPU and IDE card. Requires PCI or local bus.
System Memory & Extended Memory System Memory：Display amount of conventional memory detected during boot up. Extended Memory：Display the amount of extended memory detected during boot up. The Advance Menu PhoenixBIOS Setup Utility Advanced Security Power Boot Exit Setup Warning Item Specific Help Setting items on this menu to incorrect values may cause your system to malfunction.
Installed OS Select the operating system you use more often. Reset Configuration Data When you select yes the bios will erase all configuration data in a section of memory for ESCD (Extended System Configuration Data) which stores the configuration settings for non-PnP plug-in devices. Select Yes when required to restore the manufacturer's defaults. The default setting is NO.
password. You can set the user password to be required for starting up the system and/or entering SCU when the administrator password has been set. Beside, the user password only allows you to use some limited items for setting in the SCU. Set Supervisor Password Pressing displays the dialog box for entering the Supervisor password. In related systems, this password gives restricted access to Setup menus. Set User Password Pressing displays dialog box for entering the User password.
The Boot Menu Main Advanced PhoenixBIOS Setup Utility Security Power Boot Exit Item Specific Help Removable Devices CD-ROM Drive * Hard Drive F1 Help ESC Exit ↑ ↓ Ö Keys used to view or configure devices: expands or collapses devices with a + or p expands all enable or disables a device. <+> and <-> moves the device up or down.
drive (the only Removable Device listed). Failing that, it will attempt to boot from the Primary Master hard disk, and so on down the list. Removable Devices, Hard Drive, and Network Boot are the generic types of devices on your system from which you can boot an operating system. You may have more than one device of each type. If so, the generic type is marked with a plus or minus sign. Use the key to expand or collapse the devices marked with <+> or <->.
CMOS RAM") a special section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS configures your system according to the Setup selections stored in CMOS. During boot up, PhoenixBIOS attempts to load the values saved in CMOS. If those values cause the system boot to fail, reboot and press to enter Setup. In Setup, you can get the Default Values (as described below) or try to change the selections that caused the boot to fail.
Save Changes Selecting “ Save Changes” saves all the selections without exiting Setup. You can return to the other menus if you want to review and change your selections.
Chapter 5: Expanding The Notebook This chapter delivers the information about expanding your notebook computer by connecting other peripheral devices. Using PC Cards This computer is installed with one PC card slot on the left side of the notebook. PC Cards are credit card-sized peripheral products based on the standards developed by PCMCIA (Personal Computer Memory Card International Association) such as a Wireless LAN card, a flash memory card, SCSI card and so on.
1. Orient the card correctly. The label side of the card faces up. One of the narrow edges has a row of pinholes. This edge inserts into the slot. 2. Insert the card into the slot. The slot had protected by cover. The covers will fold out of the way when you insert the card. When the card is nearly all the way inserted, press quite firmly to ensure that the card mates properly with the connector inside the slot. 3.
Connecting a USB 2.0 Device The USB 2.0 is the new generation interface, which supports 480Mbps (max) data transfer rate. This computer has three USB 2.0 (Universal Serial Bus) ports on the left side of the computer for connecting USB devices such as mouse, external USB floppy disk drive, external USB optical drive, camera and so on. It supports “Plug and Play” technology so you can install and remove USB devices without turning off the computer. NOTE: Please download the newest USB 2.
Internal Components Upgrade Here is a list of upgrading options that are not user-serviceable: 1. DDR Memory 2. Internal hard disk Warring： We recommend that you contact your dealer and ask them to install any additional components. Installing these components by yourself may cause damage to your system.
