Installation Manual

W
H
Arm and
Wall Plate
01
x1
02
x1
Monitor Plate Extenders
03
x2
Step 3-1 Select monitor plate configuration
Step 3-2 Assemble monitor plate and extenders
Select the configuration A , B , or C to use based on the measurement from step 2.
If your TV hole pattern is greater
than 100x100mm, attach
extenders [03] to monitor plate
[02]using Nut [C] and Bolt [D] .
C
D
M-B
M-A
Use the
longer screws
M-B
M-E
M-FM-D
Step 3-3
Attach the brackets
(b) For Round Back / Extra Space
Top of TV
ST6.3 x 60mm
Lag Bolts
x2
x1
B C DA
Open-end wrench
Nuts Bolts
x4 x4
03
02
Max:200x200mm /8x8"
Min:75x75mm /3x3"
14"~40"
(V3)
If you have any questions, please contact us.
Bubble level X1
Hardware Included
Hardware (Wall /Product)
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4
x4x4
Philips Screws
M8 x 25mm
x4 x4 x4
Spacers
L5mm
x4
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
Measure and note the width and the height
of the square or rectangle formed from the
VESA holes pattern .
Step 2 Mesure your TV pattern
2M2M
Step 1-1 Select TV screw diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
M6M4
M8
Correct
Correct
Too Long
Too Short
Step 1-2 Select TV screw length
75mm ≈ 3in.
100mm ≈ 4in.
150mm ≈ 6in.
200mm ≈ 8in.
Velcro cable ties X3
Max:
(20KG)
44LBS
Safety Caution
Must Check Before Getting Started
Installation Tools (Not Included)
Band
Tape
2M
Socket
Wrench
ScrewdriverPencil Electrodrill
Stud
Finder
HammerAwl
Wood
Drill Bit
Masonry
Drill Bit
Wood Stud Installation Concrete Installation
1/2"
(13mm)
3/8"
(10mm)
5/32"
(4mm)
MAX:200mm/8"
MAX:
200mm/8"
Max:
(20KG)
44LBS
No!
No!
When attaching brackets to the flat screen, be careful not to over tighten screws and
be sure that screws do not bottom out in the mounting holes.
MU0029 INSTALLATION INSTRUCTION
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the installation, assembly
or use of this product, please contact us.
● This product is designed for use in wood stud and solid concrete wall.
- DO NOT install into drywall alone.
● The wall must be capable of supporting five times the weight of the TV and mount combined.
● Do not apply this product to any purpose not indicated by
MOUNTUP.
●
Incorrect installation may result in product damage or body injury. MOUNTUP shall bear no responsibility
for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. For parts shortage or damage,
please contact us.
Min. 8"
Min. Wood Stud Size:
nominal 2”(51mm)
actual 1 1/2”(38mm)
Min. Wood Stud Size:
nominal 4”(102mm)
actual 3 1/2”(89mm)
(203mm)
Solid concrete wall
CAUTION: DO NOT install into drywall alone.
<16mm(5/8")
Drywall with wood studs
02
B
C
D
03
M-B
M-A
Use the shorter
screws
M-B
M-C
M-E
Not for M8 screws
(a) For Flat Back
Top of TV
VESA Patter
(WxH)
Configuration
75mm x 75mm A
B
100mm x 100mm A
B
C
B
100mm x 200mm
150mm x 150mm
200mm x 100mm
200mm x 200mm
for VESA hole pattern:
100x200mm
C
for VESA hole pattern:
150x150mm, 200x200mm,
200x100mm.
B
for VESA hole pattern:
75x75mm, 100x100mm.
A
75mm
100mm
75mm
100mm
200mm
150mm
200mm
100mm
150mm
100mm
200mm
2
1
5
4
3