Use and Care Manual

ManualsBrandsmount-it! ManualsElectricalHeavy-Duty Wide Screen Tilt Wall Mount for 42 in. to 90 in. Screen Size

Installation Instruction

English

UNPACKING INSTRUCTIONS

! Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.

! Check package contents against the Supplied Parts List in the next page to assure that all components were received

undamaged. Do not use damaged or defective parts.

! Carefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

Install and operate this device with care. Please read this instruction before beginning the installation, and carefully

follow all instructions contained herein. Use proper safety equipment during installation.

Please call a qualified installation contractor for help if you:

! If you don't understand these directions or have any doubts about the safety of the installation.

! If you are uncertain about the nature of your wall, consult a qualified installation contractor.

Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby

disclaims any and all liabili

ty for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of

this product.

CAUTION!

WARNING

This TV mount must be securely attached to the vertical wall. If the mount

is not properly installed it may fall, resulting in possible injury and/or

damage.

Note: The mounting components and hardware supplied in this package are not designed for installations to

walls with steel studs or to cinder block walls. If the hardware you need for your installation is not included,

please consult your local hardware store for proper mounting hardware for the application.

Tools Required

3/16" Drill Bit

Phillips Screwdriver

1/2" Masonry Bit

Stud Finder

Wrench or Socket Set

Carpenter's Level

For model PMA-7031 6031 5031

Summary of content (4 pages)

PAGE 1
English Installation Instruction For model PMA-7031 6031 5031 UNPACKING INSTRUCTIONS ! Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. ! Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. ! Carefully read all instructions before attempting installation. IMPORTANT SAFETY INFORMATION Install and operate this device with care.
PAGE 2
Supplied Par ts List (1)Wall Plate-a (1)Left Mornitor Bracket-b (1)Right Monitor Bracket-c (1)Allen Key-d (4)M4x12 Bolt-e (4)M5x12 Bolt-f (4)M6x12 Bolt-g (4)M8x16 Bolt-h (4)M4x30 Bolt-i (4)M5x30 Bolt-j (4)M6x35 Bolt-k (4)M8x40 Bolt-l (4)M4 Lock Washer-m (4)M5 Lock Washer-n (4)M6 Lock Washer-o (4)M8 Lock Washer-p (4)M4/M5 Space-q (4)M6/M8 Space-r (8)M4/M5 Washer-s (4)M6/M8 Washer-t (2)Safety Bolt-u (6)Lag Bolt-v (6)Lag Bolt Washer-w (6)Concrete Anchor-x 2
PAGE 3
Step 1A Mounting the Monitor Brackets to a TV with Flat Back First of all, make sure the diameter of the Bolt(e,f,g,h) your TV requires. Once you have determined the correct diameter, please see the relative diagram as below. You will thread the Bolt into the TV using the correct Lock Washer(m,n,o,p) and Washer(s,t). Please make sure the Monitor Brackets(b,c) are vertically centered and level with each other.
PAGE 4
Mounting the Wall Plate to the Wall Step 2 Brick, Solid Concrete and Concrete Block mounting: Use the Wall Plate(a) as a template to mark 6 hole locations on the wall. Three in the top row of slots and three more in the bottom row. Make sure these holes are level and there is at least 6" distance between any two holes. Pre-Drill these holes with a 1/2" masonry bit to at least 2.5" in depth. Insert a Concrete Anchor(x) into each of these holes.