Use and Care Manual

ManualsBrandsmount-it! ManualsComputer & Laptop AccessoriesDual Monitor Desk Stand for 13 in. to 32 in. Monitors

Table Of Contents

English

Installation Instruction

UNPACKING INSTRUCTIONS

! Carefully open the carton, remove contents and lay out on cardboard or other

protective surface to avoid damage.

! Check package contents against the Supplied Parts List in the next page to assure

that all components were received undamaged. Do not use damaged or defective

parts.

! Carefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

! Install and operate this device with care. Please read this instruction before

installation, and carefully follow all instructions contained herein. Use proper safety

equipment during installation.

! Please call a qualified installation contractor for help if you don't understand these

directions or have any doubts about the safety of the installation.

Do not use this product for any purpose or in any configuration not explicitly specified

in this instruction. We hereby disclaims any and all liability for injury or damage

arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Summary of content (6 pages)

PAGE 1
English Installation Instruction UNPACKING INSTRUCTIONS ! Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. ! Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. ! Carefully read all instructions before attempting installation. IMPORTANT SAFETY INFORMATION ! Install and operate this device with care.
PAGE 2
Supplied Par ts List (1) Pole-a (2) VESA Plate-d (1) Weighted Base-b (1) Swivel Arm-c (3) M5x14 Bolt-e (2) Nut-h (1)M10 Bolt-i (1)Support Plate-j (1)M10 Washer-k (1) Grommet Base Plate-m (1)Wire Clip-n1 (4)Wire Clip-n2 (1)Allen Key-o (1)Wrench-p (8)M4x12 Bolt-q (8)M4x30 Bolt-r (8)M4 Spacer-s Tools Required (1)Spring Washer-l Phillips Screwdriver CAUTION! ! WARNING The monitor desktop mount must be evenly positioned on a stable horizontal surface.
PAGE 3
Step 1 Install the Pole to the Desktop Option A: Weighted Base Install 1. Install the Pole(a) to the Weighted Base(b) using 3pcs M5x14 Bolts(e), and tighten using the Allen Key(o), see Figure 1. 2. Optionally, you can drill a 10mm diameter hole in your desk and secure using the Support Plate (j), M10 Washer(k), Spring Washer(l) and M10 Bolt(i). Fasten the M10 Bolt with provided Wrench(p), see Figure 2.
PAGE 4
Step 1 Install the Pole to the Desktop Option B: Grommet Base Install a Self Drilled Grommet Hole Installation m 1. Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8" (10mm) diameter hole at the marked position through the mounting surface. e 2. Install the Grommet Base Plate(m) to the Pole(a) using 3pcs M5x14 Bolts(e), and tighten using the Allen Key(o), see Figure 5. Figure 5 3.
PAGE 5
Step 3 Attach the VESA Plate to the Monitor q s r For Monitor with Curved or Recessed Back For Monitor with Flat Back Step 4 Slide the Monitor onto the Head of Swivel Arm h Slide the monitor onto the head of Swivel Arm(c) as shown in the above diagram. Install the security Nut(h). Make sure the security nut is installed before you rotate the monitor.
PAGE 6
Step 5 Fix the Tilt Angle and Adjust the Level of Monitor o o Ignore this step if monitors are level Fix the tilt angle If one monitor is lower, remove the Nut(h) and turn the bolt counter-clockwise with supplied Allen key(o) to raise the monitor. Install the Nut(h) after the adjustment. Tighten the bolt with the supplied Allen Key(o) to fix the tilt angle. Step 6 Make the Necessary Adjustments and Manage the Wires o n1 Use the supplied Allen Key(o) to make the necessary adjustments.