Use and Care Manual

ManualsBrandsmount-it! ManualsComputer & Laptop Accessories13 in. to 27 in. Screen Size Full Motion Dual Monitor Desk Mount

MI-2752

Installation Instruction

UNPACKING INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

Carefully open the carton, remove contents and lay out on cardboard or other protective

surface to avoid damage.

Check package contents against the Supplied Parts List in the next page to assure that all

components were received undamaged. Do not use damaged or defective parts.

Carefully read all instructions before attempting installation.

Install and operate this device with care. Please read this instruction before installation, and

carefully follow all instructions contained herein. Use proper safety equipment during installa-

tion.

Please call a qualied installation contractor for help if you don't understand these directions or

have any doubts about the safety of the installation.

Do not use this product for any purpose or in any conguration not explicitly specied in this

instruction. We hereby disclaims any and all liability for injury or damage arising from incorrect

assembly, incorrect mounting, or incorrect use of this product.

Summary of content (6 pages)

PAGE 1
MI-2752 Installation Instruction UNPACKING INSTRUCTIONS Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage. Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts. Carefully read all instructions before attempting installation. IMPORTANT SAFETY INFORMATION Install and operate this device with care.
PAGE 2
Supplied Parts List (1)Pole-a (1)“C” Clamp-b (1)“C” Clamp Brace-c (1)Swivel Arm-d (2)VESA Plate-e (3)M5x14 Bolt-f (2)M8x12 Bolt-g (2)Nut-h (1)Support Plate-j (1)M10 Washer-k (1)Spring Washer-l (1)Wire Clip-n1 (4)Wire Clip-n2 (1)Allen Key-o (1)Wrench-p (8)M4x12 Thumb Bolt-q (8)M4x30 Bolt-r (8)M4 Spacer-s (1)Soft Pad-t1 (1)Soft Pad-t2 (1)M10 Bolt-i (1)Grommet Base Plate-m 2
PAGE 3
Step 1 Install the Pole to the Desktop Option A: Desk Clamp Install a 1.Install the “C” Clamp Brace(c) to the Pole (a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o),see Figure 1. c f 2. Attach Soft Pad(t1) to the “C” Clamp Brace(c), see Figure 2. t1 Figure 1 3. Install the “C” Clamp(b) to the pole assembly according to the thickness of the desktop. The thickness can be changed to three positions. Connect it using 2pcs M8x12 Bolts(g), and tighten using the Allen Key(o).
PAGE 4
Step 1 Install the Pole to the Desktop Option C: Grommet Base Install a m Self Drilled Grommet Hole Installation 1.Position the Pole(a) on the mounting surface and mark the center hole. Drill a 3/8" (10mm) diameter hole at the marked position through the mounting surface. f t2 Figure 7 2. Install the Grommet Base Plate(m) to the Pole(a) using 3pcs M5x14 Bolts(f), and tighten using the Allen Key(o), see Figure 7. Figure 8 3. Attach Soft Pad(t2) to the Grommet Base Plate(m), see Figure 8. 4.
PAGE 5
Step 3 Attach the VESA Plate to the Monitor q s r For Monitor with Flat Back Step 4 For Monitor with Curved or Recessed Back Slide the Monitor onto the Head of Swivel Arm h Slide the monitor onto the head of Swivel Arm(d) as shown in the above diagram. Install the security Nut(h). Make sure the security nut is installed before you rotate the monitor.
PAGE 6
Step 5 Make the Necessary Adjustments o o Ignore this step if monitors are level Fix the tilt angle If one monitor is lower, remove the Nut(h) and turn the bolt counter-clockwise with supplied Allen key(o) to raise the monitor. Install the Nut(h) after the adjustment. Tighten the bolt with the supplied Allen Key(o) to fix the tilt angle. Step 6 Manage the Wires and Store the Allen Keys on Wire Clip o n1 Use the supplied Allen Key(o) to make the necessary adjustments.