(Head Up Display) User Manual
Table of Contents ▣ Before use (HUD, OBD) 1. Components|5 ※ MOTREX HUD Main Body Buttons 2. HUD Installation|7 3. MOTREX HUD APP Installation & HUD Connection|10 4. WAZE APP Installation|10 5. WAZE Navigation|11 6. MOTREX HUD APP Settings|12 1) Car information settings 2) OBD information correction 3) HUD Setting 7. Display |19 8. OBD Update |22 (If the firmware related to OBD is separately operated) 9. Firmware Update|26 10.
Checklist Before Use - HUD ▶ MOTREX HUD is a navigation system that uses WAZE MAP. ▶ Both MOTREX HUD APP and WAZ APP need to be installed on the user's mobile phone. ▶ Once MOTREX HUD APP is open and the destination has been entered on WAZE, the GPS navigation can start . ▶ As the information is delivered through the WAZE server, the estimated arrival time on WAZE and HUD may not match. ▶ WAZE only works and the connection with HUD is maintained while MOTREX HUD APP is on.
Checklist Before Use - OBD ▶ For the OBD Ⅱ setting, the car must be fully started and MOTREX HUD APP must be launched. (Setting cannot be modified under ACC ON or KEY ON status.) ▶ Please reenter and save the car information after an OBD Ⅱ firmware or DB file update. ▶ Please check the information (year/fuel type/mileage) on the vehicle registration before entering the car information on OBD Ⅱ.
1.
※ MOTREX HUD Main Body Buttons Reset Power (touch sensor) - Press with a sharp object to reset the HUD. - When the power button is pressed, the LCD (TOLED) opens and turns on. - When the power button is pressed when the power is on, the LCD (TOLED) closes and the system is turned off. LCD(65K color AM TOLED) - Use the HUD APP to adjust the angle.
2. HUD Installation 1 2 3 4 Check where the OBD terminal is Set the HUD location Embed the HUD main cable Connect the HUD main cable 6 7 8 Organize the cables Connect the OBD ll module Connect the OBD ll module with the HUD main cable 5 Attach HUD to the dashboard ※ When the first OBD module is connected to the vehicle, the HUD will illuminate for 10 minutes. Please set up the vehicle in the MOTREX HUD APP.
4) Connect the HUD main cable to the HUD. (When connecting the HUD main cable, make sure the thicker part does not get inside the place for the cables as shown in the image below.) 5) Attach the HUD on the dashboard. (Install the HUD on the cradle and remove the 3M tape to attach the HUD on the dashboard.) (Choose the cradle of your preference between the adjustable type and the fixed type.) Adjustable Type Fixed Type * Above images are provided for reference. 6) Use the clips to organize the line.
7) Connect the OBD module to the OBD terminal. 8) Connect the OBD module with the HUD main cable.
3. MOTREX HUD APP Installation and HUD Connection 1) Open App Store (iOS) or Google Play Store (Android) on the smartphone. 2) Search for “MOTREX HUD”. 3) Download and install MOTREX HUD APP from App Store (iOS) or Google Play Store (Android). 4) Open MOTREX HUD APP. 5) Install MOTREX HUD APP and use Bluetooth to connect the smartphone with HUD. 6) When the Bluetooth connection pop-up appears on the smartphone display, select “Accept”.
5. WAZE Navigation 1) When the car starts, MOTREX HUD automatically turns on. 2) Open MOTREX HUD APP on the smartphone. 3) Press Navigation to start WAZE. 4) Type in the destination. 5) Search for the route and press Start Navigation to start the guide. ※ The car information setting must be completed in MOTREX HUD APP to use HUD. ※ Both MOTREX HUD APP and WAZE APP should be installed on the smartphone. ※ When MOTREX HUD APP stops, HUD and the smartphone become disconnected.
6. MOTREX HUD APP Settings MOTREX HUD HUD-related settings Start the WAZE Navigation application. Car information settings When auto start is enabled, WAVE Navigation starts automatically when MOTREX HUD turns on. See the software version, user manual, and firmware updates. ※ Before setting up the HUD, proceed to the vehicle information setting. ※ When the navigation auto-run is checked - The WAZE APP runs automatically when you run the MOTRE HUD APP.
1) Car information settings Select Car info Settings Select CAR SETTING Enter the car i nformation and click SET Select DB file (Select the first file) ※ Visit the MOTREX website to check which car models are supported by OBDⅡ. ※ Please set the vehicle to OBD II Standard for use if it is not in the vehicle settings. (It is limited to Hyundai and Kia vehicles.
■ 14 Click “Yes” on the pop-up to upload Uploading OBD file OBD car setting completed Vehicle information update is complete
2) OBD information correction Select Car info Settings If you do not have a vehicle on the OBD II supported vehicle list, you can use it by entering the OBD II Standard information. After OBDⅡ setting, the adjustment value can be modified if the speed, fuel consumption shown on the dashboard while driving are significantly different. ※ Make sure to press the Apply button after changing the setting.
3) HUD settings Select HUD Settings When brightness is set to Auto, the display brightness is adjusted automatically with the illumination sensor. Between -10% and +10%, additional adjustment can be made to the current brightness level. When Auto is not selected, the user can manually adjust the brightness from 0% to 100%. *Setting the brightness to 100% always instead of selecting the auto brightness control may shorten the life of the display.
Set the background image for booting. When set to Auto, it changes according to the date on the phone. Select the unit of distance to be shown on HUD Select whether to auto start HUD. When selected, HUD automatically turns on when the car starts. * For HUD setting and navigation information, launch HUD APP and enter the destination for navigation. Select the fuel display information to display. When selected, the fuel information is shown on the display.
Set whether to show the battery charge rate on the display. When checked, the battery charge rate shows on the display. * Battery voltage is displayed for non-IBS cars. Set whether to use average fuel efficiency. An arbitrary number is shown on the display i nstead of the user information. Shows the device connected to HUD. Reset to factory default.
7. Display [With destination setting] 1. Navigation - Distance to the primary point 2. Remaining distance 5. Driving distance/driving time time /DPF status 6. Gas (warning): Possible distance to drive or remaining gas Coolant temperature: -40 to 150 4. Bluetooth connection 3. Estimated arrival time 7. IBS car: Charge rate non-IBS car: Battery voltage 8. Car speed 9. Average fuel efficiency ※ Driving distance, driving time and average fuel efficiency is for one trip.
Display Description 1 Direction and distance to the primary point when the destination has been set * BAR icon appears when the distance remaining to the destination is less than 200m.
[Without destination setting] Car speed Driving distance/driving time /DPF status Gas (warning): Distance to empty or remaining gas Coolant temperature: -40 to 150 Bluetooth connection IBS car: Charge rate Average fuel efficiency non-IBS car: Battery voltage ※ Information on display may vary depending on the car model.
8. OBDⅡ Update 1) Firmware update ※ Install the OBDⅡ firmware additionally when the OBDⅡ firmware has been updated. ※ Download the OBDⅡ firmware for MOTREX HUD from the MOTREX website. · MOTREX website : www.motrex.co.kr ▶ Android (1) Connect the mobile phone with the computer. (2) Put downloaded OBDⅡ firmware file into the H100 folder on the mobile phone. (3) Disconnect the mobile phone from the computer. (4) Type in the destination. (5) Start the car and launch MOTREX HUD APP.
Click Software Updating firmware Click FIRMWARE UPDATE Select “Yes” on the pop-up for update Firmware update is complete Pop-up closes once the firmware update is completed. HUD is disconnected and restarts. ※ Keep the smartphone near HUD and keep the engine going during the update. ※ HUD connection must be maintained during the firmware update. ※ If you press Stop during the update, the update stops. When the update is restarted, it starts from the beginning again.
2) DB file update ※ Install the OBDⅡ DB file additionally when the OBDⅡ file information has been updated. ※ Download the OBDⅡ firmware for MOTREX HUD from the MOTREX website. · MOTREX website : www.motrex.co.kr ▶ Android (1) Connect the mobile phone with the computer. (2) Put downloaded OBDⅡ DB file into the H100 folder on the mobile phone. (3) Disconnect the mobile phone from the computer. (4) Start the car and launch MOTREX HUD APP. ▶ iOS (1) Connect the mobile phone with the computer. (2) Open iTunes.
Click on Car info Settings Select CAR SETTING Select DB file (Select the first file) Enter the car information and click SET Click “Yes” on the Uploading OBD file Vehicle information update is complete OBD car setting completed pop-up to upload 25 ■
9. Firmware Update 1) Launch App Store (iOS) or Google Play Store (Android) on the mobile phone. 2) Enter “MOTREX HUD” in the search box. 3) Update the app on App Store (iOS) or Google Play Store (Android). ※ If there is an update, the update button for MOTREX HUD APP on App Store (iOS) or Google Play Store (Android) becomes active. 4) Update the firmware from the MOTEX HUD APP. ※ A total of two updates can be made to Micro, OBD II, after each update the HUD will be rebooted.
Updating firmware Firmware update is complete Pop-up closes once the firmware update is completed. HUD is disconnected and restarts. ※ If firmware update is enabled after updating the MOTREX HUD APP in the APP store(iOS) or Google Play store(Android), please proceed with firmware update. ※ The update order is in the order of Micom and OBD II. ※ Keep the smartphone near HUD and keep the engine going during the update. ※ HUD connection must be maintained during the firmware update.
10. Product Specifications and Other Information 1) Product specifications Model name MTXH100 Product name Head Up Display Processor ARM Cortex M4 Display 65K color AM TOLED Resolution 360 x 112px Sensor Illumination sensor, touch sensor Wireless connection method BLE Power 12V only (OBDⅡ connection) HUD application MOTREX HUD (iOS 10.0 or higher / Android 5.0 or higher) Interlocked mobile navigation WAZE (iOS 10.0 or higher / Android 5.
2) FCC regulations FCC Warning This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residental installation. This equipment generates, uses and can radiate radio frequency energy and, if nor installed and used in accordance with the instructions, may cause harmful interference to radio cummunications.
(Head Up Display) User Manual