AP650 Access Point INSTALLATION GUIDE
AP650 Access Point Introduction .........................................................................................................................................4 1.1 Document Conventions .......................................................................................................................... 4 1.2 Warnings ................................................................................................................................................ 4 1.3 Site Preparation ......
Installation Guide 4.3.1 Safety Information ..................................................................................................................... 23 4.4 International ......................................................................................................................................... 23 4.5 EU ......................................................................................................................................................... 23 4.6 US and Canada .....
1 AP650 Access Point Introduction The AP650 access point, a component of the Motorola Wireless Controller System, links wireless 802.11a/b/g/n devices to the controller, enabling growth of your wireless network with a cost-effective alternative to standard Access Points. The AP650 access point provides two placement options: wall and ceiling. Wall mount slots fit onto two screws provided. Arrows on the case guide placement of the screws.
Installation Guide • Verify that cable lengths are within the maximum allowable distances for optimal signal transmission. 1.4 AP650 Package Contents The AP650 model Access Point comes in four configurations, two Integrated Antenna models and two External Antenna models. The contents of the package differ between the Integrated Antenna model and the External Antenna model. 1.4.
AP650 Access Point 1.5 Features • • • • • • One RJ-45 connector LED indicators Safety wire tie point Slots for wall mounting Clips for mounting on a suspended ceiling T-bar Lock port for Kensington® style Security Lock The AP650 access point has one RJ-45 connector supporting an 10/100/1000 Ethernet port and requires 802.3af-compliant power from an external source. NOTE When operating in a Gigabit Ethernet environment CAT-5e or CAT-6 cable is required for Gigabit operation.
Installation Guide 2 7 Hardware Installation 2.1 Installation Instructions The AP650 Access Point mounts either on a wall with wide-shoulder screws or on a suspended ceiling T-bar. This unit is not designed for mounting on a desk. To prepare for installation, perform the following steps: 1. Match the model number on the purchase order with the model numbers in the packing list and on the case of the device shipped. 2.
AP650 Access Point 2.3 Access Point Placement For optimal performance, install the Access Point away from transformers, heavy-duty motors, fluorescent lights, microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls or floors block transmission. Install the Access Point in an open area or add Access Points as needed to improve coverage. Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough.
Installation Guide 9 2.4.2 Wall Mount Procedure Integrated Antenna Wall Mount 1. Orient the case on the wall by its width or length. Correct Orientation ! CAUTION Incorrect Orientation To ensure proper operation of the AP650 Access Point ensure that the thin Access Point is mounted in the correct orientation as shown above. 2.
AP650 Access Point 3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall mounting screw and stop when there is 1mm between the screw head and the wall. NOTE 4. 5. 6. 7. 8. When pre-drilling a hole the recommended hole size is 2.8mm (0.11in.) if the screws are going directly into the wall and 6mm (0.23in.) if the provided wall anchors are being used. If required, install and attach a security cable to the unit’s lock port.
Installation Guide 11 2.5 Integrated Antenna Model Suspended Ceiling T-Bar Mount Instructions Ceiling mount requires holding the AP650 Access Point up against a T-bar of a suspended ceiling grid and twisting the case onto the T-bar. 2.5.1 Suspended Ceiling Mount Procedure 1. 2. 3. 4. 5. 6. 7. 8. If required, install and attach a security cable to the unit’s lock port. Plug the Ethernet cable into the unit and to a controller with an 802.3af-compatible power source.
• AP650 Access Point Safety wire (recommended) and security cable (optional) NOTE In the event that the original mounting screws are lost, the following screws can be used instead: (ANSI Standard) #6-18 X 0.875in. Type A or AB Self-Tapping Screw, or (ANSI Standard Metric) M3.5 X 0.6 X 20mm Type D Self-Tapping Screw. 2.6.2 Wall Mount Procedure 1. Orient the case on the wall by its width or length. 2.
Installation Guide 13 4. If required, loop a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter, around the tie post and secure the loop. 5. If required, install and attach a security cable to the unit’s lock port. 6. Place the large corner of each of the case’s mount slots over the screw heads. 7. Slide the case down along the mounting surface to hang the mount slots on the screw heads. 8. Attach appropriate antennas to the connectors. 9.
AP650 Access Point 2.7.2 Ceiling Mount Procedure Light Pipe Ceiling Tile Badge 1. 2. 3. 4. 5. If possible, remove the ceiling tile from its frame and place it, finished side down, on a work surface. If required, install a safety wire, between 1.5mm (.06in.) and 2.5mm (.10in.) in diameter, in the ceiling space. If required, install and attach a security cable to the unit’s lock port. Mark a point on the upper or unfinished side of the tile.
Installation Guide 15 2.8 AP650 External Antenna Model Antenna Options Motorola supports two antenna suites for AP650 External Antenna models. One antenna suite supporting the 2.4 GHz band and another antenna suite supporting the 5 GHz band. Select an antenna model best suited to the intended operational environment of your Access Point. On single radio versions, the R-SMA connectors can support both bands and should be connected to a R-SMA dual-band antenna or an appropriate single band antenna. The 2.
AP650 Access Point 2.9 LED Indicators Both the Integrated Antenna model and the External Antenna model have LED activity indicators on the front of the case for use with wall mount. With the External Antenna model unit mounted above a ceiling, LEDs are at the center of an oval badge on the ceiling; a light pipe enables viewing the back LEDs through the ceiling tile. The LEDs provide a status display indicating error conditions, transmission, and network activity for the 5 GHz 802.
Installation Guide 17 Task 5 GHz Activity LED (Amber) 2.
3 AP650 Access Point Specifications 3.1 AP650 External Antenna Model Electrical Characteristics An AP650 External Antenna model Access Point has the following electrical characteristics: Operating Current & Voltage 180mA- 270mA @ 48VDC 3.2 AP650 External Antenna Model Physical Characteristics An AP650 External Antenna model Access Point has the following physical characteristics: Dimensions 8.50 in. Depth x 5.5 in. Width x 1.5 in. Height 21.59 cm Depth x 13.97 cm Width x 3.
Installation Guide 19 3.3 AP650 Integrated Antenna Model Electrical Characteristics An AP650 Integrated model Access Point has the following electrical characteristics: Operating Current & Voltage 180mA- 270mA @ 48VDC 3.4 AP650 Integrated Antenna Model Physical Characteristics An AP650 Integrated Antenna model Access Point has the following physical characteristics: Dimensions 9.50 in. Depth x 7.5 in. Width x 1.9 in. Height 24.13 cm Depth x 19.05 cm Width x 4.83 cm Height Housing Plastic Weight 2.
AP650 Access Point 3.5 Radio Characteristics An AP650 model Access Point has the following radio characteristics: Operating Channels All channels from 4920 MHz to 5825 MHz except channel 52 -64 Channels 1-13 (2412-2472 MHz) Channel 14 (2484 MHz) Japan only Actual operating frequencies depend on regulatory approval for the country of use. Data Rates Supported 802.11b: 1, 2, 5.5, and 11Mbps 802.11g: 1,2,5.5,11,6,9,12,18,24,36,48, and 54Mbps 802.11a: 6,9,12,18,24,36,48, and 54Mbps 802.
Installation Guide 4 21 Regulatory Information This device is approved under the Symbol Technologies brand: Symbol Technologies, Inc., is the Enterprise Mobility business of Motorola, Inc. (“Motorola”). This guide applies to Model Number AP-650 All Motorola/Symbol devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website: http://supportcentral.motorola.
AP650 Access Point 4.1.2 Frequency of Operation – FCC and IC 5 GHz Only The use on UNII (Unlicensed National Information Infrastructure) Band 1 5150-5250 MHz and Band 3 5470 - 5725 MHz is restricted to indoor use only, any other use will make the operation of this device illegal. Devices using the 5470 – 5725 MHz band shall not be capable of transmitting in the band 5600 - 5650 MHz in the US, this “Notched” band has been disabled in the US version of the Access Point. The available channels for 802.
Installation Guide 23 Other Medical Devices Please consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device. 4.3 RF Exposure Guidelines 4.3.1 Safety Information Reducing RF Exposure—Use Properly Only operate the device in accordance with the instructions supplied. 4.
AP650 Access Point 4.8 Radio Frequency Interference Requirements—FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Installation Guide 4.10 CE Marking and European Economic Area (EEA) The use of 2.4 GHz RLAN’s, for use through the EEA, have the following restrictions: • • • Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz. France, outside usage is restricted to 2.4 – 2.454 GHz. Italy requires a user license for outside usage. 4.
AP650 Access Point 4.12 Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Motorola for recycling. For information on how to return product, please go to: http://www.motorola.com/recycling/weee. Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Motorola pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.motorola.
Installation Guide 27 Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.motorola.com/recycling/weee weboldalra. Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Motorola för återvinning. Information om hur du returnerar produkten finns på http://www.motorola.com/recycling/weee.
AP650 Access Point 4.14 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE この装置は、情報処理装置等電波障害自主規制協議会 （ＶＣＣＩ）の基準に基づくク ラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としています が、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引 き起こすことがあります。取扱説明書に従って正しい取り扱いをして下さい。 This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference.
Installation Guide 29 4.16.3 Chile “Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas.”. "This device complies with the Resolution Not 403 of 2008, of the Undersecretary of telecommunications, relating to electromagnetic radiation.” 4.16.4 Mexico Restrict Frequency Range to: 2.450 – 2.4835 GHz. 4.16.
AP650 Access Point The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices. 臺灣 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自 變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象 時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干 擾。 Wireless device operate in the frequency band of 5.25-5.35 GHz, limited for Indoor use only. 在 5.25-5.35 赫頻帶內操作之無線資訊傳輸設備，限於室內使用。 4.16.
Installation Guide 5 31 Customer Support If you have a problem with your equipment, contact Enterprise Mobility support for your region. Support and issue resolution is provided for products under warranty or that are covered by an Enterprise Mobility Services agreement. Contact information and web self-service is available by visiting http://supportcentral.motorola.com/.
6 AP650 Access Point AP-650 Access Point China ROHS Compliance 有毒有害物质或元素 部件名称 (Parts) 金属部件 (Metal Parts) 电路模块 (Circuit Modules) 电缆及电缆组件 (Cables and Cable Assemblies) 塑料和聚合物部件 (Plastic and Polymeric Parts) 光学和光学组件 (Optics and Optical Components) 电池 (Batteries) 15 六价 铬 (Cr6+) O 多溴二 苯醚 (PBDE) O 铅 (Pb) 汞 (Hg) 镉 (Cd) X O O X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O 多溴 联苯 (PBB) O O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以 下。 X：表示该有毒有害物质至少
Installation Guide 33
AP650 Access Point
Installation Guide 35
Motorola Solutions, Inc. 1301 E. Algonquin Rd. Schaumburg, IL 60196-1078, U.S.A. http://www.motorolasolutions.com MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. © 2012 Motorola Solutions, Inc. All Rights Reserved.
