Mobile Laptop 900™ Model L3393, L3394 Motorola, Inc. Commercial, Government and Industrial Solutions Sector All rights reserved Owner’s Manual R02 Part No.
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice.
Regulations Information Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner.
FRENCH ATTENTION: II y a danger d’ explosion s’ il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’ un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. Attention (for USA Users) The product that you have purchased contains a rechargeable battery. The battery is recyclable.
Table of Contents Preface ....................................................................................... v Chapter 1 Getting Started..................................................... 1-1 Getting the Computer Running..............................................1-2 Unpacking .......................................................................1-2 Connecting to AC Power .................................................1-3 Opening the Cover.........................................................
Numeric Keypad ..............................................................2-5 Euro Symbol....................................................................2-6 Windows Keys.................................................................2-6 Function Keys..................................................................2-6 Fn Key.............................................................................2-7 Hot Keys ..........................................................................
Chapter 4 Expanding Your Computer ................................. 4-1 Connecting an External Monitor............................................4-2 Connecting a USB Device .....................................................4-3 Connecting a Serial Device....................................................4-4 Connecting an IR Device.......................................................4-5 Connecting a Bluetooth-compliant Device (option) ...............4-7 Connecting an IEEE 1394 Device ..................
Location Guidelines .........................................................7-3 General Guidelines...........................................................7-3 Cleaning Guidelines.........................................................7-4 Battery Pack Guidelines ...................................................7-4 When Traveling ....................................................................7-5 Chapter 8 Troubleshooting ..................................................
Preface This manual contains information that will help you operate the computer. It is divided into 8 chapters and an appendix. l Chapter 1, Getting Started, takes you through the process of setting up the computer and identifying its external components. l Chapter 2, Operating Your Computer, tells you how to use the computer’ s components and features. l Chapter 3, Managing Power, provides information on power.
l Appendix B, Fingerprint Recognition System, provides information on using the system’ s fingerprint recognition system. Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information which, if not followed, may result in loss of data or damage to the computer. Keyboard keys are shown in a bold typeset.
CHAPTER 1 Getting Started Congratulations on purchasing this computer. This high performance notebook computer is especially designed for the practical applications of warehouses, automobiles, vehicles, public security, repairing, assisting the handicapped, and other demanding situations where conventional notebook computers just cannot measure up. This chapter first tells you step by step how to get the computer up and running.
Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should find these standard items: l Notebook computer l Accessories: − AC adapter (100~240 VAC, 50/60 Hz) − AC power cord (US/CE/UK/SA) − Driver CD − This Operation Manual Inspect all the items. If any item is damaged or missing, notify your dealer immediately.
NOTE: Power Supply Cord: (optional) Detachable, minimum 1.5 m long. Listed, rated minimum 125 V, 7 A, having a 2/18 AWG, type SVT flexible cord. One end terminates with a parallel blade, molded-on, attachments plug with a 7 A, 125 V (NEMA 1-15P) configuration; other end terminates with a molded-on appliance coupler. Alternative: (optional) Detachable, maximum 4.5 m (14.76 ft) long. Listed, rated minimum 250 V, 6 A, having a 3/18 AWG, type SVT flexible cord.
CAUTION: z When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer. A reverse procedure may damage the AC adapter or the computer. z When unplugging the connector, always hold the plug head. Never pull on the cord. NOTE: When the AC adapter is connected, it also charges the battery pack. For information on using battery power, see Chapter 3. Opening the Cover CAUTION: Be gentle when opening and closing the cover.
3. Each time the computer is turned on, it performs a Power-On Self Test (POST), and the operating system such as Windows should start. Turning Off To turn off the computer power, use the “Shut Down” command of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer. (See “Stopping the Computer” in Chapter 2 for information.
Taking a Look at the Computer This section identifies the external components of the computer and briefly describes the function of each component. NOTE: Depending on the model you purchased, the appearance of your computer may not exactly be the same as those shown in this manual. Right-Side Components Ref Component Description See Also n IEEE 1394 Port Connects a 1394 device, such as a scanner, printer, digital camera, joystick, and more.
Left-Side Components Ref Component Description See Also n IR Port Connects an IrDA-compliant device for wireless data transfer. P. 4-5 o Bluetooth Port (option) Connects a bluetooth-capable device for wireless data transfer. P. 4-5 p Microphone Connector Connects an external microphone. q Keyboard BIOS Use this to turn off the system when resetting the system using Ctrl+Alt+Del does not work. Reset Switch P.
Rear Components Ref Component Description See Also n DVI-I Port Connects an external monitor with a DVI interface. P. 4-2 o Serial Port Connects a serial device, such as an external modem. P. 4-4 p Docking Port For connecting to a Port Replicator / car mount (both are available as an option). q Rear Cover Latch Locks the rear cover. r USB Ports Each of the two ports connects a USB device, such as a floppy disk drive, printer, digital camera, joystick, and more. P.
Ref ” Component Description Battery Charge Glows green when the battery is fully charged and connected to AC power. Indicator See Also P. 3-3 Glows amber (orange) when the battery is being charged.
Front Components Ref Component Description See Also n Wireless Modem Antenna Serves as the antenna for the optional wireless modem (RDLAP, GPRS and CDMA). P. 2-23 o Stereo Speaker Set Sends out sound and voice from the computer. P. 2-20 p Handle Allows you to carry your computer for an easy grip. Wireless LAN Antenna Serves as the antenna for the WLAN. It is builtin the handle. P. 2-22 GPS Antenna (option) Serves as the antenna for the Global Positioning System (GPS).
Bottom-Side Components Ref Component n X-bay Module Antenna Connector Serves as the interface between the system and external antenna of the optional X-bay module. o CD/DVD Drive Lock/Unlock Switch Allows you to lock the CD/DVD drive in place. P. 2-15 p CD/DVD Drive Eject Latch Allows you to remove the CD/DVD drive (can also contain the Combo drive). P. 2-15 q GPS Antenna Connector Serves as the interface between the system and external GPS antenna. P.
Ref Component Description See Also ‘ Ventilation Openings Do not cover or block the ventilation openings for air circulation thus preventing overheating. ’ Battery Pack Supplies power to your computer when external power is not connected. “ X-Bay Interface Connects additional wireless modem (GPRS/ (top right) GSM). 1-12 Mini PCI Slot (bottom right) Inside is the Mini PCI slot for using an optional Mini PCI card.
Top-open Components Ref Component Description See Also n Fingerprint Scanner Contains the fingerprint sensor. P. B-1 o Keyboard Serves as the data input device of the computer. P. 2-4 p Power Button Turns the computer power ON and OFF. P.
Ref • Component Device Indicators Description See Also Show the current status of the computer’ s devices. Power on / Standby mode indicator P. 1-3 Hard disk drive in-use indicator P. 2-13 Num Lock indicator P. 2-6 Caps Lock indicator P. 2-4 Scroll Lock indicator P. 2-4 • LCD Screen Displays the output of the computer. P. 2-17 ‘ Light Sensor Automatic light sensor for dimming the display’ s backlight.
Ref Component Description AC in and HDD heater on indicator – Glows green when the computer is connected to AC power. Blinks red when the hard disk heater is on. Getting Started See Also P. 1-4 P.
Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose … Do this … To know more about the computer … Go on to the next chapter. To install the operating system if your dealer has not already done so … See the operating system manual. To know more about the operating system … Read the operating system manual. To install the drivers if your dealer has See Chapter 6.
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button. A computer starts up with an operating system (OS) existing on the storage device such as the hard disk; or from a floppy disk or CD if you have the respective modules installed. The computer will automatically load the OS after you turn it on. This process is called booting.
To stop in this mode … Do this … To start up or resume again Hibernation Depending on your settings in Windows, you can place the computer in Hibernation mode by: • Closing the display cover. • Pressing the power button Press the power button. If you choose to stop in Standby or Hibernation mode, you can return to where you left off the next time you start up the computer. (See “Power Management” in Chapter 3 for more information.
Using the Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn key added for specific functions. The standard functions of the keyboard can be further divided into four major categories: l Typewriter keys l Cursor-control keys l Numeric keys l Function keys Typewriter Keys Typewriter keys are similar to the keys on a typewriter. Several keys are added such as the Ctrl, Alt, Esc, and lock keys for special purposes.
Cursor-Control Keys NOTE: The word “cursor” refers to the indicator on the screen that lets you know exactly where on your screen anything you type will appear. It can take the form of a vertical or horizontal line, a block, or one of many other shapes.
Numeric keys facilitate entering of numbers and calculations. When Num Lock is on, the numeric keys are activated; meaning you can use these keys to enter numerals. NOTES: l When the numeric keypad is activated and you need to type the English letter in the keypad area, you can turn Num Lock off or you can press Fn and then the letter without turning Num Lock off. l Some software may not be able to use the numeric keypad on the computer. If so, use the numeric keypad on an external keyboard instead.
Fn Key The Fn key, at the lower left corner of the keyboard, is used with another key to perform the alternative function of a key. The letter “Fn” and the alternative functions are identified by the color of blue on the keytop. To perform a desired function, first press and hold Fn, then press the other key. Hot Keys Hot keys refer to a combination of keys that can be pressed any time to activate special functions of the computer. Most hot keys operate in a cyclic way.
Key Description Switches the display output to one of the following when an external device is connected. Upon booting the system with CRT: LCD CRT LCD & CRT NOTES: l If the display mode is set to 256 colors or lower, or in DOS mode, there will be only two modes for selecting: CRT only and LCD & CRT. l This function only applies to Plug & Play CRT monitors. Serves as the sleep button that you can define with Windows’ Power Management. (See the “Power Management” in Chapter 3.
Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTES: z By default, the touchpad is disabled. Use the Fn+F7 hot keys to enable/disable this function. The touchpad indicator found on the keyboard panel glows red when it is disabled. z For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly. Do not use excessive force.
Term Action Point Move your finger on the pad until the cursor points to the selection on the screen. Click Press and release the left button. –or– Tap gently anywhere on the pad. Doubleclick Press and release the left button twice in quick succession. –or– Tap twice on the pad rapidly. Drag and drop Press and hold the left button, then move your finger until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination.
Configuring the Touchpad You may want to configure the touchpad to suit your needs. For example, if you are a left-handed user, you can swap the two buttons so that you can use the right button as the left button and vise versa. You can also change the size of the on-screen pointer, the speed of the pointer, and so on. To configure the touchpad, you can use the standard Microsoft or IBM PS/2 driver if you are using Windows.
Using the Touchscreen (option) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. The touchscreen is a touch-sensitive device that allows you to communicate with the computer by controlling the location of the pointer on the screen and making selection with the buttons. The touchscreen needs a special device driver support that allows you to easily use the computer without a mouse or touchpad.
Using the Hard Disk Drive Your computer comes with a hard disk drive as drive C. A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored. Your hard disk drive is a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive.
Using the CD/DVD/Combo Drive Depending on the model, your computer comes with a CD, DVD or Combo drive located on the right side of the computer. This drive is usually configured as drive D. The drive uses removable 5.25-inch silver discs, which look like standard music CDs. It is an ideal medium to use for distributing multimedia because of the huge amount of data that a disc can store. Depending on the model, your drive is one of the following: l CD drive can read CDs, audio CDs, CD-R, and CD-RW discs.
NOTE: For DVD/Combo drive only. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
NOTE: For DVD/Combo drive only. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Removing the CD/DVD/Combo Drive To remove the CD/DVD/Combo drive: 1. Remove the two screws (n). 2. Slide the CD drive lock/unlock switch to the unlock position (o) and pull the CD/DVD/Combo drive out of the CD drive bay (p).
Inserting and Removing a CD NOTE: The following procedure applies to inserting or removing a DVD disc as well. Follow this procedure to insert or remove a CD. 1. Turn on the computer. 2. Press the eject button and the CD tray will slide out partially. Gently pull on it until it is fully extended. 3. To insert a CD, place down the CD in the tray with its label facing up. Slightly press the center of the CD until it clicks into place.
Using the Video Features The video subsystem of your computer features: l 12.1/13.3-inch TFT (Thin-Film Transistor) color LCD display with 1024x768 XGA (Extended Video Graphics Array) resolution. l 64 MB integrated video memory. l Simultaneous display on LCD and external monitor, which is useful when you have a presentation as you can control the screen from your computer and face the audience at the same time.
Your computer has been set to a default resolution and number of colors before shipment. You can view and change display settings through your operating system. See your operating system documentation or online help for specific information. For displaying in higher resolutions, you can connect an external CRT monitor that supports higher resolutions. (See “Connecting an External Monitor” in Chapter 4 for more information.) The following table lists the display modes supported by your computer.
Using the Audio Features NOTES: z To take advantage of the enhanced audio capabilities, the audio driver supplied with your computer must be installed (see chapter 6 for details). z If you experience interference while recording, try lowering the microphone recording volume.
Connecting Audio Devices For higher audio quality, you can send or receive sound through external audio devices. l ) can be connected to an external Microphone Connector ( microphone for recording voice or sound. l Audio Output Connector ( ) can be connected to the line-in connector of powered speakers with built-in amplifiers, headphones, or earphone set. This connector is compliant with S/P-DIF (Sony/Philips-Digital InterFace). You can connect audio equipment with S/P-DIF to the computer.
Using the Communication Features Using the LAN NOTE for Windows 2000: To take advantage of the LAN feature, the LAN driver supplied with your computer must be installed. The internal 100Base-T LAN (Local Area Network) module allows you to connect your computer to a network. It supports data transfer rate up to 100 Mbps. To connect the network cable to the LAN module, connect one end of the LAN cable to the RJ-45 connector on the computer and the other end to the network hub.
Using the Wireless LAN Depending on your model, an internal Mini PCI wireless LAN (WLAN) card may have been pre-installed by your computer manufacturer at the factory. This card allows you to access corporate networks or the Internet in a wireless environment. The WLAN features include: l IEEE 802.11b standard compliance l 2.
NOTE: The FAA (Federal Aviation Agency) has deemed it unsafe to operate wireless devices in aircraft as this may interfere with flight safety. Remember to select turn off wireless LAN when using your computer in the airplane. Replacing the Wireless LAN To replace the Wireless LAN, follow these steps: 1. Make sure the computer is not turned on or connected AC power. 2. Remove the 6 screws of the HDD cover and lift the Mini PCI Wireless module to take it off the computer.
Your computer can send and receive data via a mobile network using the GSM protocol. To send or receive data over a GSM network, you must have an account with a service provider that supports GSM data services, and the service provider must enable the data features on your account.
stations. GPS uses these "man-made stars" as reference points to calculate positions accurate to a matter of meters. In fact, with advanced forms of GPS you can make measurements to better than a centimeter! In a sense it is like giving every square meter on the planet a unique address. Here's how GPS works in five logical steps: l The basis of GPS is "triangulation" from satellites. l To "triangulate," a GPS receiver measures distance using the travel time of radio signals.
2-26 Operating Your Computer
CHAPTER 3 Managing Power Your computer operates either on external AC power or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
AC Adapter CAUTION: The AC adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. l The AC power cord supplied with your computer is for use in the country where you purchased your computer. If you plan to go overseas with the computer, consult your dealer for the appropriate power cord. l When you disconnect the AC adapter, disconnect from the electrical outlet first and then from the computer.
Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time. NOTE: Care and maintenance information for the battery is provided in the “Battery Pack Guidelines” section in Chapter 7.
Initializing the Battery Pack You need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging. It can take several hours. 1. Make sure the computer power is turned off. Connect the AC adapter to fully charge the battery pack. 2. After the battery pack is fully charged, turn on the computer. 3.
Replacing the Battery Pack CAUTION: z There is danger of explosion if the battery is incorrectly replaced. Replace the battery only with the computer manufacturer’s optional battery packs. Discard used batteries according to the dealer’s instructions. z Do not attempt to disassemble the battery pack.
5. Replace the battery pack compartment cover and secure the four screws. Battery Low Signals and Actions Battery Low occurs when the battery has approximately 10% (Windows default setting) of its charge remaining. The computer gives warning ) blinks red to beeps or messages and the Battery Low Indicator ( alert you to take actions. NOTE: You can set up your threshold and signals of Battery Low under Windows. Immediately save your data upon Battery Low.
Power Management Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving. With an ACPI-compliant operating system such as Windows 2000 and Windows XP, power supply to different computer components is controlled on an as-needed basis. This allows maximum power conservation and performance at the same time.
Hibernation Hibernation is a very useful feature. People frequently open many applications when they use computers. It takes some time to get all these applications open and running, and normally they all have to be closed before the system can be turned off. When you use the hibernation feature, you do not have to close the applications. The computer stores the state of your computer to a file on the hard disk and then shut down.
Power-Saving Tips In addition to your computer’ s automatic power management, you can do your part to maximize the battery’ s operating time by following these suggestions. l Do not disable Power Management. l Decrease the LCD brightness to the lowest comfortable level. l Disable the parallel and serial ports if no devices are connected to these ports. (See “Components Menu” in Chapter 5.
