APPLICANT: MOTOROLA, INC. FCC ID: IHDT6FL1 INSTRUCTION MANUAL • A preliminary draft copy of the User’s Manual follows this cover page. • The User’s Manual will have the following text added to it: "NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DoCoMo W-CDMA and GSM/GPRS Systems Thank You for Purchasing the “FOMA M2501 HIGHSPEED”. Before or while using the FOMA M2501 HIGH-SPEED, be sure to thoroughly read this manual to ensure its correct use. For further information, contact the “DoCoMo Information Center” on the back page of this manual. Treated with care, your FOMA M2501 HIGH-SPEED will be your able partner.
How to Read/Refer to This Manual In this manual, illustrations and symbols are used in the explanations so that you can easily understand how to use the FOMA terminal correctly. • This manual describes operations mainly using a mouse to click on an item. How to Refer to This Manual By the following search methods, you can find pages where functions and services are described: From the Index Search from the index when you know the names of functions or services.
From the Index P95 Search for a function name or a service name as shown below. O Operating Environments Communication Configuration File (Driver) . . . . . . . . . . 24 FirstPass PC Software. . . . 39 FOMA PC Configuration Software . . . . . . . . . . . . 24 Utility. . . . . . . . . . . . . . . . . 52 Using an Earphone Microphone . . . . . . . . . . . . . . . . . . . . . 86 Utility . . . . . . . . . . . . . . . . 51, 52 Card Settings . . . . . . . . . . . 64 Help . . . . . . . . . . . . . . . . . .
A section title b Launching/Exiting Click [追加 (Add)] Launching/Exiting the FOMA M2501 HIGH-SPEED Utility An item name actually shown on the screen. Some functions cannot be performed depending on operations. Launching • Log into a user account with the Administrator or PC supervisor privileges. Operation steps a Double click the “M2501 HIGHSPEED Utility” icon on the c Perform the following steps Name Desktop The Main screen (P54) opens.
ñ⁄éü Contents How to Read/Refer to This Manual ......................................................................................................................... 1 Features of the FOMA M2501 HIGH-SPEED ......................................................................................................... 5 Safety Instructions (ALWAYS FOLLOW THESE DIRECTIONS)............................................................................. 6 Handling and Care ...........................................
Features of the FOMA M2501 HIGH-SPEED FOMA (Freedom Of Mobile multimedia Access) is the name of a service provided by DoCoMo based on the W-CDMA system, which is certified as one of the global standards of 3rd generation mobile communication systems (IMT-2000). You can enjoy high-speed packet communication with a maximum of 3.6 Mbps for receiving and 384 Kbps for sending. ・ The actual communication speed varies depending on the signal strength or surrounding communication conditions.
Safety Instructions (ALWAYS FOLLOW THESE DIRECTIONS) ●Before using your FOMA terminal, read these safety instructions carefully so that you can use it correctly. After reading the safety instructions, keep them in a safe place for later reference. Contents/Safety Instructions ●These precautions are intended to protect you and others around you. Read and follow them carefully to avoid injury, damage to the product or damage to property.
General Precautions for the FOMA Terminal and UIM DANGER malfunction may result. Do not let FOMA terminal and UIM get wet. Avoid water ●Contact with water or other liquids may cause heating, electric shock, fire or malfunction. Take care not to use the terminal and UIM in areas where they could get wet. Do not use or leave the FOMA terminal and UIM in places with a high temperature such as near fire or heater, or places exposed to direct sunlight or in cars under the blazing sun.
CAUTION Keep out of reach of babies and infants. ●Accidental swallowing or injury may result. Contents/Safety Instructions If children use the FOMA terminal or UIM, a guardian should explain the safety instructions and correct operations. The guardian should also make sure that the instructions are followed during use. ●Injury may result. Do not place the FOMA terminal or UIM on unstable locations such as wobbly tables or slanted locations.
WARNING Do not use the terminal while driving a vehicle. ●In accordance with the revision of terminal could hit you and others, causing accidents such as injury and the FOMA terminal could become damaged. CAUTION following: Part Material Silver colored area on the front and back Stainless steel Screw on the back Steel Do not allow liquids such as water, or foreign materials such as metal pieces or flammable materials to get into the UIM tray on the FOMA terminal.
Notes on Using near Electronic Medical Equipment ■The description below meets “Guideline on the Use of Radio-communication Equipment such as Cellular Telephones - Safeguards for Electronic Medical Equipment” by the Electromagnetic Compatibility Conference Japan. Contents/Safety Instructions WARNING Remove the FOMA terminal from PC card slot when in crowded trains or other public places where implanted cardiac pacemaker or defibrillator wearers could be nearby.
Handling and Care General Usage Guidelines ■Clean the FOMA terminal with a soft, dry cloth (Glasses cloth). If the FOMA terminal is wiped with alcohol, paint thinner, benzine or detergent, the printing may disappear or color may fade. ■Do not place the FOMA terminal where excessive force will be applied to it. If FOMA terminal is inserted to a full bag, or placed in a pocket and sat on, its internal PCBs may be damaged or malfunction. Such damage is not covered by warranty.
UIM ■Do not use excessive force to remove the UIM. ■Do not put excessive force on the card when inserting it into the terminal. ■It is normal for the UIM to become warm during use. You can continue to use it even when it is warm. Contents/Safety Instructions Handling and Care 12 ■Note that NTT DoCoMo will not be liable for malfunctions occurring as the result of inserting and using a UIM with unrecommended IC card reader/writer. ■Always keep IC portion of the UIM clean.
Intellectual Property Rights Copyrights and Rights of Portrait Trademarks ・ The “FOMA”, “mova”, “mopera”, “mopera U”, “WORLD CALL”, “WORLD WING”, “Dual Network”, “DoCoMo Video Phone Software”, “FirstPass”, “Public Mode”, “My DoCoMo”, and “FOMA” logo are trademarks or registered trademarks of NTT DoCoMo. “Catch Phone” is a registered trademark of the Nippon Telegraph and Telephone Corp. The “Free Dial Service” name and its logo are trademarks of NTT Communications.
Purchased Product and Accessories ■FOMA M2501 HIGH-SPEED (With Warranty) ■FOMA M2501 HIGH-SPEED CD-ROM • • Contents/Safety Instructions • • • DE E OD M MO T T AN AN • • M2501 HIGH-SPEED通信設定ファイル (M2501 HIGHSPEED Communication Configuration File) FOMA PC設定ソフト (FOMA PC Configuration Software) FirstPass PCソフト (FirstPass PC Software) M2501 HIGH-SPEEDユーティリティ (M2501 HIGHSPEED Utility) ドコモテレビ電話ソフト 2005 (DoCoMo Video Call Software 2005) FOMA パケットバイトカウンタ (FOMA Packet Byte Counter) FOMA M2501 HIGH-SPEED 取扱
Before Using the FOMA Terminal Names of Parts and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UIM (FOMA Card) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Available Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the FOMA Terminal and a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Names of Parts and Functions f Before Using the FOMA Terminal Top View a b d Names of Parts and Functions 16 e INSERT Front c Rear c ・ The antenna of the FOMA terminal is embedded in the main unit.
FOMA Terminal Status Lamp Antenna Lamp The FOMA HIGH-SPEED terminal failed An invalid UIM is inserted a UIM not inserted/not recognized Lights red E D O M A PIN Code/PUK Code must be entered b The PIN code block is on The UIM is an IC card that stores personal information such as your phone number. Without the UIM inserted in the FOMA terminal, you cannot make voice calls, video calls or data communications. For details on the UIM, refer to the instruction manual for the UIM.
Removing a Slide the release lever in the direction of the arrow UIM Versions There are two versions of the UIM. The following table describes the differences: Function Before Using the FOMA Terminal Release Lever b Remove the UIM from the card slot UIM (Green) UIM (Blue) FirstPass Available* Not Available WORLD WING Available* Not Available *: This FOMA terminal cannot acquire the user authentication required for FirstPass directly.
• Communication charges become high when performing communications with large data such as browsing Web sites with many graphics or downloading data. • The “FOMA Packet Byte Counter” can be downloaded from the DoCoMo application download Web site. http://www.nttdocomo.co.jp/support/download/index. html Charges for this communication method are based on the duration of the connection.
Voice Calls/Video Calls Voice Calls Charges for this communication method are based on the connection time. Video Calls Charges for this communication method are based on the connection time. Video calls are available between terminals compatible with DoCoMo’s video calls (comply with “3G-324M*1 standardized by 3GPP*2, international standard”). Before Using the FOMA Terminal *1: 3G-324M is an international standard for 3rd generation mobile video calls.
c Double-click the card icon in the task tray on the Desktop Connecting the FOMA Terminal and a PC ▼ Inserting • Install the UIM to the FOMA terminal before using. →P17 a b Turn on the PC Hold the FOMA terminal with the label side up and slide straight into the PC card slot • If “FOMA M2501 USB Host Controller” appears, the FOMA terminal is correctly installed. • If the above name does not appear after a while, turn off your PC, verify the connection and try again.
Removing Disconnect the line when communicating, and remove the FOMA terminal. a Double-click the card icon in the task tray Before Using the FOMA Terminal b Select “FOMA M2501 USB Host Controller”, and click [停止 (Exit)] Connecting the FOMA Terminal and a PC c Click [OK] d When a message indicating that the PC card can be removed safely, remove the FOMA terminal from PC • Always store the removed FOMA terminal in the FOMA M2501 HIGH-SPEED terminal card case.
Setting Up Before Setting Up Setting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Communication Configuration File (Driver) Communication Configuration File (Driver) . . . . . . . . . . . . . . . . . . . . . . . . . . 24 FOMA PC Configuration Software Configuring Communication Using the FOMA PC Configuration Software ............................................................... FOMA PC Configuration Software . . . . . . . . . . . . . .
*1: Japanese Version Service Pack 4 or later *2: Japanese Version Service Pack 1 or later Setting Up • Required memory or available hard disk space may vary depending on the system environment. Install the following software from the included CDROM for the FOMA M2501 HIGH-SPEED terminal. 1 • Depending on the operating environment, the software may not work.
d Verify the destination folder and click i Select “一覧または特定の場所からインス トールする(詳細) (Install from a list or a [Install] specific location (Advanced))” and click [次へ (Next)] Screen to be replaced • [Browse] : You can change the destination folder. However, you can only specify folders on a local hard disk. Other folders (on a network drive or removable media) cannot be specified. e Click [続行 (Continue)] • This software behaves in the same way as Windows logo certified software. Click [続行 (Continue)].
l Install the other three drivers f Click [OK] Install all three drivers referring to Steps 8-11. For Windows 2000 a Start Windows and insert the FOMA Screen to be replaced M2501 HIGH-SPEED CD-ROM to the PC b Click [スタート (Start)] y “ファイル名を指 定して実行 (Select file name and run)” c Click [参照 (Browse)] to specify the file the FOMA terminal into the PC g Insert card slot (P21) h Click [次へ (Next)] i Select “デバイスに最適なドライバを検索 setup.
[参照 (Browse)] to specify the file, k Click then click [OK] a Open the Windows Control Panel ■ For Windows XP Click [スタート (Start)] y “コントロールパネル (Control Panel)” • Specify the file “:/Drivers” (the CD-ROM drive letter varies depending on the configuration of your PC).
a Start “プログラム(アプリケーション)の 追加と削除 (Add or Remove Programs (Applications))” from Windows ■ For Windows XP Click [スタート (Start)] y “コントロールパネル (Control Panel)” y “プログラムの追加と削除 (Add or Remove Programs)” icon ■ For Windows 2000 Click [スタート (Start)] y “設定 (Settings)” y “コントロールパネル (Control Panel)” y “アプ リケーションの追加と削除 (Add or Remove Applications)” icon b Select “M2501 Datacard USB Driver (Tentative Name)” and click [変更と削除 (Change/Remove)] Select “M2501 Datacard USB Driver” For Windows 2000 * The COM port number vari
Configuring Communication Using the FOMA PC Configuration Software Setting Up Configuring Communication Using the FOMA PC Configuration Software 29
FOMA PC Configuration Software Setting Up FOMA PC Configuration Software 30
Installing the FOMA PC Configuration Software Verifying that the FOMA terminal is Recognized Correctly by the PC Installing Setting Up Installing the FOMA PC Configuration Software 31
Configuring Communication Settings Specifying the Communication Port Selecting “Packet Communication” from Easy Settings Using “mopera U” or “mopera” as an access point Using another provider as an access point Setting Up Configuring Communication Settings 32 Selecting “64K Data Communication” from Easy Settings Using “mopera U” or “mopera” as an access point Using another provider as an access point
Start Communicating Disconnecting Setting Up Start Communicating 33
Uninstalling the FOMA PC Configuration Software Before Uninstalling Uninstalling Setting Up Uninstalling the FOMA PC Configuration Software 34
W-TCP Settings Role of W-TCP Software Setting and Deleting Optimization For Windows XP For Windows 2000 Setting Up W-TCP Settings 35
Configuring Access Points (APN) Adding/Editing/Deleting Access Points Saving to a File Reading from a File Reading Access Point (APN) Information from the FOMA Terminal Writing Access Point (APN) to the FOMA Terminal Setting Up Configuring Access Points (APN) 36 Creating a Dial-up Connection
Dial-up Network Settings Setting Packet Communication Verifying the COM Port Number For Windows XP For Windows 2000 Configuring Access Points (APN) Configuring a Dial-up Network in Windows XP Setting 64K Data Communication Dial-up Network Settings Configuring a Dial-up Network in Windows 2000 Setting Up Setting Display/Hide Caller ID 37
Connecting Using Dial-up Disconnecting Setting Up Connecting Using Dial-up 38
Before Installing Using FirstPass PC Before installing the FirstPass PC Configuration software, read the “FirstPass Manual” (in PDF format) in the “FirstPass PC Soft” folder contained in the included CD-ROM. Adobe Reader (version 6.0 or later is recommended) is required to view the file. The latest version of Adobe Reader can be downloaded from the Adobe System’s Web site (separate communication charges apply). For details, visit the Adobe System’s Web site.
AT Commands AT commands are used to check the FOMA terminal function settings or status using a PC. Usually, the communication software issues AT commands so that you do not need to be concerned about them. Use AT commands if you want to control the FOMA terminal in your own way.
AT Command List The following AT commands can be used on the FOMA M2501 HIGH-SPEED. • [&F] : A command to initialize settings used as AT&F command. • [&W] : A command to save settings used as AT&W command. ATZ command can restore set values. • [?] [=?] : The current settings appear when adding “?” at the end of the command, and the effective range of the current settings appear when adding “=?” at the end of the command. AT Command Overview AT¥S Show the command settings and S register.
AT Command Parameters/Description Command Examples Show the signal strength at the FOMA terminal. =0 : Out of service area =1 : One antenna bar =2 : Two antenna bars =3 : Three antenna bars AT*DGPIR= The setting of this command becomes valid when a call is dialed. 184/186 can also be added to the APN number even for the setting in a dial-up network. n=0 (default) : Use APN as it AT*DGPIR=0 is. OK n=1 : Add “184” to APN (always hide). n=2 : Add “186” to APN (always show).
AT Command AT+CGREG= [&F] [&W] [?] [=?] AT+CGSN Overview Parameters/Description Command Examples Set whether to be notified of the n=0 (default) : Do not notify. AT+CGREG=1 OK network registration status. n=1 : Notify when outside and inside the service area is changed. Execute “AT+CGREG?” then appears as “+CGREG : ,”. n : Setting value. start=0 : Outside the packet service area. start=1 : Inside the packet service area. start=4 : Unknown.
AT Command Parameters/Description Command Examples Setting Up AT Command List Display the own number of the FOMA terminal. Executing “AT+CNUM” displays in the format of “+CNUM : , ” number : phone number type=129 : Excluding the international access code+ type=145 : Including the international access code+ AT+CNUM +CNUM;,+819 012345678”, 145 OK AT+CPAS Display FOMA terminal state. Executing “AT+CPAS?” displays in the format of “+CPAS : ”. n=0 : Available to set AT commands.
AT Command AT+CREG= Overview Set whether to show Out of service area or in the service area. [&F] [&W] [?] [=?] AT+GMI Display the manufacturer of the FOMA terminal. ー AT+GMI +GMI : “Motorola CE, Copyright 2006” OK (checking the specifications) ー AT+GMM +GMM : “GSM900”,“GSM1800”, “GSM1900”, “WCDMA”,“MODEL= M2501 HIGH-SPEED” OK (checking the specifications) ー AT+GMR +GMR : “M2501 HIGH-SPEED_ 12_34.56.78” OK Display the name of the FOMA terminal. Display FOMA terminal’s version.
AT Command Command Examples Start packet communication or 64K data communication. Overview Packet communication : ATD*99***# X to X : +CGDCONT 64K data communication : ATD Packet communication : ATD*99***1# CONNECT 64K data communication : ATD XXXXXXXXXX CONNECT ATE [&F] [&W] Set whether to echo back the text sent from a PC. n=0 : Not to echo back. n=1 (default) : Echo back. ATE1 OK ATH Disconnect packet communication or 64K data communication.
AT Command ATS6= [&F] [?] ATS7= [&F] [&W] [?] ATS8= [&F] [?] ATS10= [&F] [&W] [?] [&F] [?] ATS103= ATS104= [&F] [?] ATV [&F] [&W] ATX [&F] [&W] Command Examples ATS6=5 OK Set the maximum waiting time (in seconds) from the starting of packet communication or 64K data communication until the connection is established. ATS7=60 OK n=1 to 255 (default n=60) : However, the values between 121 to 255 are regarded as 120.